USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 8
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 701.The tang of a file is the part that __________.
- 702.When a lathe is used for thread cutting, the number of threads per inch produced is determined by the speed relationship between the __________.
- 703.Subcooling is a method of reducing the temperature of the liquid refrigerant below its __________.
- 704.The valve which is most suited for regulating the flow through a pipeline is a __________.
- 705.A centrifugal pump must have a stuffing box liquid sealing line and seal cages installed if the pump __________.
- 706.A standard grade of 3 inch steel pipe has an outside diameter of 3.5 inches and an inside diameter of 3.068 inches. What is the nominal size of steel pipe having an outside diameter of 4.0 inches and an inside diameter of 3.548 inches?
- 707.Which of the screwdrivers listed is produced with a tip to fit screws with a four-way or cross slot?
- 708.In order to prevent overheating of the packing in the stern tube stuffing box, __________.
- 709.Many micrometers are equipped with a ratchet stop at the end of the thimble to __________.
- 710.A follower rest should be used with a lathe to machine __________.
- 711.Which of the drill sets listed would commonly be referred to as a 'Jobbers Set'?
- 712.If the chemical analysis of a lube oil sample taken from the main propulsion machinery indicates an increased neutralization number the __________.
- 713.The proper design of a centrifugal pump must include a seal cage and sealing line when the pump __________.
- 714.Some vessels are equipped with a water lubricated stern tube. When at sea, operating under normal conditions, the water service valve from the ship's saltwater system to the bearing should be __________.
- 715.The correct torque value for a micrometer torque wrench is reached when __________.
- 716.To commence cutting threads with a metal lathe, you should engage the __________.
- 717.When using a micrometer to measure a drill for size, you should measure across the drill __________.
- 718.A good quality lubricating oil used in any machinery, should be __________.
- 719.Centrifugal pumps are designed with sealing lines __________.
- 720.An 8" diameter wheel is driving a 20" diameter wheel via a pair of belts. The power input is supplied by a 5 HP motor rotating the driving wheel at 300 RPM. If the efficiency of the transmission is 80%, what RPM and torque is delivered to the driven wheel?
- 721.A rotameter, when used to indicate the rate of fluid flow in distilling plants, is essentially an area meter consisting of a __________.
- 722.Which of the following methods applies to how a vacuum is created by a jet pump or an eductor?
- 723.For greater accuracy, some micrometers have a vernier scale making it possible to read in increments of __________.
- 724.The 60° taper angle machined on work supported by lathe centers is most easily machined by the __________.
- 725.Under normal conditions, the refrigerant enters the compressor in an operating refrigeration system as a __________.
- 726.The most accurate method of measuring the setting of an inside caliper is to use a/an __________.
- 727.Sealing lines provide sealing liquid flow to the stuffing box of a centrifugal pump __________.
- 728.As routine maintenance, the bilge manifold valves are periodically removed and examined. Prior to re-securing the valve bonnets, the valve __________.
- 729.A hydrometer measures specific gravity by comparing the __________.
- 730.An excessive amount of water is prevented from entering a vessel using a water lubricated stern tube bearing by the use of the __________.
- 731.A micrometer screw has a pitch of __________.
- 732.A taper may be turned on a lathe by __________.
- 733.Refrigerant enters the condenser as a __________.
- 734.If the thimble of a micrometer were turned through one complete revolution, the micrometer would open or close by a linear distance of __________.
- 735.A micrometer would be used to measure __________.
- 736.Early models of the flash-type evaporators used a separate shell-and-tube heat exchanger as the air ejector condenser. More recent models use a combined air ejector condenser with the __________.
- 737.If the pump for a hydraulic anchor windlass is overheating, the cause may be __________.
- 738.Coast Guard Regulations (46 CFR), require that an indicating light, located at the propulsion control station, be illuminated if there is an overload that would cause overheating of the __________.
- 739.When a vessel is underway, a small amount of water is allowed to leak through the water lubricated stern tube stuffing box in order to __________.
- 740.The rotating part of a micrometer is the known as the __________.
- 741.To safely change spindle speeds on a lathe, you must first __________.
- 742.A small hole gauge is used in conjunction with a/an __________.
- 743.The function of seal cages, or lantern rings installed in the centrifugal pump stuffing boxes, is to __________.
- 744.The capacity of a particular ballast pump is 200 gallons per minute. Approximately how long will it take to ballast a tank with 68.5 long tons of seawater?
- 745.Coast Guard Regulations (46 CFR) require an audible and visible alarm to be actuated in the pilothouse when the actual position of the rudder differs from the position ordered by the follow-up control system by 5 degrees° or more for more than __________.
- 746.An oil fog lubrication system is recommended for __________.
- 747.The collision bulkhead is located __________.
- 748.According to Title 46 CFR, of the equipment listed below, which equipment must be tested NOT more than 12 hours prior to getting underway from a U.S. port when the voyage is to be of 48 hours or greater duration?
- 749.In a flash distilling unit, evaporator feed (seawater) first absorbs heat in the __________.
- 750.Which of the listed numeric values represents the smallest size drill?
- 751.Which of the lathe operations listed is best done with the carriage locked in position?
- 752.If you turn the adjusting screw clockwise of a spring-loaded, internal pilot, pressure reducing valve, you will __________.
- 753.The function of lubricating oil is to __________.
- 754.While at sea, the flash type evaporator is discharging the output to the distill tanks. If it becomes necessary to reduce the feed water temperature below 165°F, you should __________.
- 755.If hot oil comes in contact with a diesel engine turbocharger, catches fire, and causes in excess of $(USA)25,000 damage to your ship, by law this must be reported to the __________.
- 756.Coast Guard Regulations (46 CFR), make certain requirements regarding over current protection. Steering gear feeder circuits shall be protected only by __________.
- 757.Carbon deposits forming on the discharge valves of an air compressor are caused by oil deterioration under high pressure. The first step in reducing these deposits would be to __________.
- 758.When a flash evaporator is being operated in extremely cold water, you may need to throttle the seawater supply to __________.
- 759.The dead center of a lathe can be properly used only after the end of the work piece has been __________.
- 760.Flash gas formed in the liquid line of a refrigeration system may cause __________.
- 761.Which of the drill sizes listed represents the largest size drill?
- 762.Overheating of the hydraulic fluid in an electro-hydraulic anchor windlass can result from a/an __________.
- 763.According to Coast Guard Regulations (46 CFR), which of the following statements is correct regarding the steering apparatus requirements for a vessel over 250 feet in length?
- 764.A dirty intercooler on the ship service air compressor will result in __________.
- 765.Which of the listed conditions will cause the feed water, that has not flashed to vapor in the first-stage of a flash evaporator, to flow into the second-stage?
- 766.In a refrigeration system, the heat normally producing the flash gas at the thermostatic expansion valve, is obtained from __________.
- 767.Sealing lines provide sealing liquid flow to the stuffing box of a centrifugal pump __________.
- 768.A twist drill gage can be used to measure the drill's __________.
- 769.Under normal operating conditions, the highest temperature and pressure conditions existing for flash-type evaporators will occur in the __________.
- 770.Electric and electro-hydraulic steering gear motors are required by Coast Guard Regulations (46 CFR) to be __________.
- 771.A dirty intercooler on an air compressor will cause __________.
- 772.Which of the following actions should be taken if during a routine maintenance inspection of a centrifugal pump, localized scoring on a pump shaft sleeve is detected?
- 773.Which of the metals listed below can be cut with the highest operating lathe speed?
- 774.High vapor superheat in a refrigeration system, may be caused by a/an __________.
- 775.In a two-stage flash-type evaporator, excess brine in the first stage automatically passes __________.
- 776.The size of a drill is usually marked on the __________.
- 777.Coast Guard Regulations (46 CFR) require that electric and electro-hydraulic steering gear motors shall be __________.
- 778.Excessive lube oil consumption by a reciprocating air compressor can be caused by __________.
- 779.The total length of stroke in a reciprocating steam pump can be adjusted by __________.
- 780.Which of the following statements best defines 'depth of cut' in lathe work?
- 781.In which of the listed refrigeration system components does superheating of the refrigerant take place?
- 782.The vacuum maintained in the salt water feed heater shell of a flash-type evaporator is generally accomplished by __________.
- 783.Sounding tubes and access openings for fuel oil tanks on cargo vessels are permitted by Coast Guard Regulations (46 CFR) to be located in which of the listed spaces?
- 784.An electric driven steering gear power unit is required by Coast Guard Regulations (46 CFR) to be capable of putting the rudder over from 15° on one side to 15° on the other side in not more than 60 seconds under emergency power with the vessel running ahead. For a 20 knot vessel, this test must be carried out at __________.
- 785.Excessive lube oil consumption in a reciprocating air compressor is an indication of __________.
- 786.Which of the lubricants listed is the best to use on a reciprocating pump rod?
- 787.When stock is being turned down on a lathe, the outside diameter is reduced by an amount equal to __________.
- 788.In a refrigeration system, the amount of refrigerant admitted to the evaporator is directly related to __________.
- 789.If the drill point lips are of unequal length, the drill will wobble and __________.
- 790.If you are cutting off a piece of stock in a lathe and the work piece tends to climb over the top of the cutoff tool, you should __________.
- 791.The refrigerant gas returning to the compressor should be __________.
- 792.The distillate produced by a flash evaporator has a salinity of 0.21 grains per gallon, with a feed water temperature entering the first-stage of the evaporator at 170°F. Under these conditions the three-way solenoid valve will __________.
- 793.On a multistage flash-type evaporator, the flash chamber is __________.
- 794.The heated feed water entering any flash chamber of a flash-type evaporator will __________.
- 795.Coast Guard Regulations (46 CFR) require tank sounding tubes terminating above the weather deck of a cargo vessel to be fitted with a __________.
- 796.According to Coast Guard Regulations (46 CFR Part 58), a power driven auxiliary steering gear for a vessel capable of a 12 knot service speed, must be able to meet the rudder movement requirements at which of the minimum vessel speeds listed below?
- 797.If the electric motor driving an air compressor fails to start, the cause may be a __________.
- 798.If you determine that a steam reciprocating pump is operating with too long of a stroke, causing the piston nut to strike the cylinder head, you should __________.
- 799.When steel, cast iron, or other metals with surface scale are being turned, the first roughing cut should be taken __________.
- 800.The low pressure side of a refrigeration system is considered to exist from the __________.