USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 16
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1501.Allowances may be made for the expansion and contraction in piping by the use of expansion joints or __________.
- 1502.For any given volume of compressed air produced by a multistage air compressor, interstage cooling will __________.
- 1503.Solid contaminants are prevented from entering the main lube oil system by way of the main engine sump, through the use of __________.
- 1504.When the steering wheel is turned, oil is directed to the steering gear rams by __________.
- 1505.Penetrations and openings in watertight bulkheads in a vessel of less than 100 gross tons must __________.
- 1506.Operating a reciprocating air compressor without an air filter will cause __________.
- 1507.Which of the flange types listed identifies the construction of a pipe joint where a flange is slipped over a length of pipe, the pipe end is heated, then setup (flanged) in a special machine, and then the end of the pipe is machined to form the actual face of the joint?
- 1508.Which of the following statements is correct concerning antifriction bearings installed on pumps?
- 1509.A water regulating valve controls the refrigeration condenser cooling water flow in response to condenser __________.
- 1510.Which of the screwdrivers listed has a tip surrounded by parallel fluted ridges resembling the ridges of a splined socket wrench?
- 1511.Proper internal lubrication of a hydraulic anchor windlass left idle for extended periods can be accomplished by __________.
- 1512.If the flow rate to a linear actuator is reduced by half of the original amount, the __________.
- 1513.Irregular feeding or surging of the feedwater supply to a flash evaporator may be attributed to __________.
- 1514.Operating a reciprocating air compressor without an air intake filter can result in a/an __________.
- 1515.The nameplate of a reciprocating pump lists the following numerals as indicated 7" X 6" X 4". The diameter of the steam cylinder is __________.
- 1516.An arrow stamped on the valve body of a water regulating valve indicates the __________.
- 1517.Which of the following frequent maintenance procedures is required of compressed air receivers?
- 1518.The main difference between a common lathe dog and a safety lathe dog is that the latter __________.
- 1519.The penetration of watertight bulkheads and watertight decks by rigid nonmetallic piping is prohibited except when __________.
- 1520.The brake horsepower of a centrifugal pump will vary directly as the __________.
- 1521.Which type of Marine Sanitation Device (MSD) is used solely for the storage of sewage and flushwater at ambient air pressure and temperature?
- 1522.Any unusual, or new vibration in the hull or propeller shafting can be an indication of __________.
- 1523.A reheater in an air conditioning system functions to __________.
- 1524.Oiling a file as a rust preventative may cause __________.
- 1525.For cutting cast iron or soft steel, the proper hacksaw blade should have __________.
- 1526.An air tank rusts out, explodes and causes $(USA) 24,000 damage to the engine room. By law, this accident is required to be reported to __________.
- 1527.'Respiratory heat' is a term applied primarily to which of the following cargoes?
- 1528.To prevent the unnecessary loading of an air conditioning system while maintaining the designed dry bulb temperature and relative humidity in an air conditioning system, you should __________.
- 1529.Which of the files listed will have coarsely spaced teeth?
- 1530.Screwdrivers designed for electrical use should have __________.
- 1531.Which of the files listed is produced with two safe edges?
- 1532.Which of the listed statements describes specific heat?
- 1533.To add refrigerant to the low side of an air conditioning system, the refrigerant should be introduced through the __________.
- 1534.Which of the following devices is not considered to be a pressure vessel? (46 CFR)
- 1535.Which of the files listed is commonly referred to as a 'rattail' file?
- 1536.Which of the screwdrivers listed is fastest and most convienent when tightening many screws?
- 1537.Which of the screwdrivers listed is designed for the precision assembly of small parts?
- 1538.You discover an air leak at the manhole cover shortly after pressurizing a P-tank. You must __________.
- 1539.Unusual hull, or propeller shaft vibrations can be caused by __________.
- 1540.If a refrigeration compressor in a multi-box system runs continuously, the cause might be a __________.
- 1541.The terms rough, coarse, bastard, second cut, smooth, and dead smooth refer to the __________.
- 1542.By which of the listed methods may heat be transferred from one body to another?
- 1543.Which of the screwdrivers listed is designed with the shaft made from double coil wire or tightly coiled steel?
- 1544.A file coated with oil and stowed away will __________.
- 1545.The length of a file is always measured exclusive of the __________.
- 1546.Which of the following statements describes the accepted method for testing a thermostatic expansion valve?
- 1547.Which of the files listed is tapered on three sides and is used to file acute internal angles?
- 1548.Which of the screwdrivers listed is produced with a tip to fit screws with a fourway or cross slot?
- 1549.To cut drill rod, light angle iron, or tool steel with a hand hacksaw, it is best to use a blade with __________.
- 1550.What is the lowest permissible flashpoint of the oil used in a hydraulic valve actuating system that operates at 145 psi (1000kPa)? (46 CFR Part 58)
- 1551.Which of the saw blades listed, when mounted in a hand held hacksaw frame, will cut on both the forward and reverse strokes?
- 1552.Any air mixture whose dew point remains constant will also have an unchanging __________.
- 1553.A fluid power system shall be so designed __________.
- 1554.A hacksaw blade with 14 teeth per inch should be used to cut __________.
- 1555.Which of the files listed will have medium spaced teeth and is used for general work?
- 1556.Which of the files listed is tapered on all sides and used to enlarge rectangular-shaped holes and slots?
- 1557.A refrigerated container filled with 10,000 lbs. of strawberries has been loaded on your ship. The set point of the box is 35°F and the interior box temperature is 90°F, and after 7 hrs. 37 minutes the box is lowered to 60°F. Based on the following informaion, which of the listed steps should be taken? (Specific heat of cargo is 0.94 BTU/LB/°F, heat gain by container equals 4000 BTU/hr., and refrigeration capacity equals 3.42 tons).
- 1558.The dew point is reached when the wet bulb temperature is __________.
- 1559.If the superheat value of a thermostatic expansion valve is set too low, the __________.
- 1560.Using a file without a handle may result in __________.
- 1561.A new file should be broken in carefully by filing a piece of __________.
- 1562.The edge of a file not having any teeth is known as a __________.
- 1563.A saw blade produced of bonded tungsten-carbide particles and mounted in a hacksaw frame is known as a __________.
- 1564.If a thermostatic expansion valve is adjusted for too high a superheat value __________.
- 1565.Pinning is often caused by __________.
- 1566.It is not necessary to 'chalk' a file when the metal being filed is __________.
- 1567.Which of the saws listed would be more suitable for cutting metal in tight quarters or flush to a surface where a hand held hacksaw frame could not be used?
- 1568.The function of a heat interchanger used in a refrigeration system is to __________.
- 1569.According to regulations (46 CFR), who may grant an extension of the tailshaft examination interval?
- 1570.It is necessary to 'chalk' a file when the metal you are filing is __________.
- 1571.What is the theoretical time necessary to reduce the temperature of 40,000 pounds of onions (placed in a refrigerated container) from 75°F to a set point temperature of 46°F? (The specific heat of onions is 0.90 BTU/LB/°F. The trailer heat gain is 6,500 BTU/hr, with a properly operating refrigeration cooling capacity of 45,500 BTU/hr).
- 1572.When cutting sheet metal too thin to be held in your hand while using a hand held hacksaw, the sheet metal should be placed between two __________.
- 1573.When opening or closing compressor service and line valves on a typical refrigeration system, you __________.
- 1574.While filing, you can prevent pinning by keeping the file clean and rubbing the teeth of the file with __________.
- 1575.An obstructed expansion valve may be indicated by an incompletely cooled evaporator and __________.
- 1576.Mill files are always __________.
- 1577.Which term applies to a hacksaw blade having short sections of teeth bent in opposite directions?
- 1578.If a liquid drying agent is used in a refrigeration system already equipped with a solid drying agent, the liquid drying agent will __________.
- 1579.One of the determining factors regulating the time interval for drawing a vessel's tailshaft depends upon the design to reduce stress concentrations. Which of the following factors, in part, would be considered to meet this design criteria?
- 1580.According to Coast Guard regulations (46 CFR) lamp, paint and oil lockers, and similar compartments shall __________.
- 1581.Double cut files are used for __________.
- 1582.Which of the files listed will have closely spaced teeth for finishing to a smooth surface?
- 1583.Your vessel has received a refrigeration container of 16 long tons of cabbage, loaded at 1700 hours on Friday, with a beginning temperature of 80°F. At what time on Saturday will the box theoretically reach its set point temperature of 50°F, assuming the system is operating correctly? (The specific heat of cabbage is 0.94 BTU/LB./°F. The container has a heat gain of 6,000 BTU/hr, and the refrigeration system's capacity is 40,000 BTU/hr).
- 1584.If an expansion valve is adjusted for too low a superheat value __________.
- 1585.Reduced capacity, accompanied by vibration and noise at the suction of a centrifugal pump, results from cavitation in the fluid being pumped. Cavitation describes the formation of __________.
- 1586.Overcharging an air-cooled refrigeration system will cause the __________.
- 1587.Which of the problems listed could happen if you attempted to force open a valve 'frozen' in position by using a wrench on the handwheel?
- 1588.Archimedes' principle states that the resultant pressure acting on a body immersed in a fluid __________.
- 1589.When mounted in a hand held hacksaw frame, which of the blades listed could cut smoothly through a metal file?
- 1590.Which of the statements listed accurately applies to controllable pitch propeller systems?
- 1591.According to Coast Guard regulation (46 CFR), an "A" class division, bulkhead or deck shall be constructed __________.
- 1592.A fine wire bristled brush used for cleaning files is called a __________.
- 1593.The type of tooth set on a hacksaw blade where the teeth are continuously staggered with one to the left and one to the right is known as __________.
- 1594.Relative humidity can be determined by using a psychrometric chart and a/an __________.
- 1595.A small obstruction at the thermostatic expansion valve inlet will result in which of the following conditions?
- 1596.According to Coast Guard regulations (46 CFR), a "B" class bulkhead shall be constructed __________.
- 1597.The term referring to the amount or degree the teeth of a hacksaw blade are pushed out or canted from the blade center is known as __________.
- 1598.A lower thermostatic temperature setting will provide a desired degree of comfort in a room where __________.
- 1599.According to Coast Guard regulation (46 CFR), a "C" class division, bulkhead or deck shall be constructed __________.
- 1600.The teeth of a file may 'clog up' with metal filings and scratch your work. This condition is known as __________.