USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 5
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 401.A sight glass is installed in the liquid line to indicate the condition of the refrigerant charge and may also indicate the __________.
- 402.To accurately cut the proper size gasket for installation in a pipeline, you should use __________.
- 403.If one of the bilge system manifold valves does not properly seat, the __________.
- 404.The portion of a mechanism that utilizes manual positioning, or automatic indexing, is known as a detent. An example of a detent used aboard ship can be found in a/an __________.
- 405.In certain circumstances, weldments are preheated before each pass to __________.
- 406.Which of the filter/strainer units listed permits you to clean the element while leaving the system on the line?
- 407.A liquid sight flow indicator in a refrigeration system is examined and gas bubbles are noted in motion with the fluid flow. This means __________.
- 408.A manual process used to remove small irregularities by grinding the contact surfaces together of a valve, is called __________.
- 409.The thickest deposit of scale in a flash evaporator is most likely to occur in the tubes of the __________.
- 410.When a linear actuator (cylinder) is being retracted without an applied load, the pressure on the oil leaving the 'cap end' will be __________.
- 411.A recirculating line is provided in the potable hot water system to __________.
- 412.For cutting thin tubing or sheet metal, the proper hacksaw blade should have __________.
- 413.The action necessary to use the steering gear room trick wheel when transferring the steering control from the wheelhouse to local control, is to __________.
- 414.In an operating refrigeration system low on refrigerant, a liquid line sight glass will __________.
- 415.Why should the use of metallic or semi-metallic packing hooks or pullers be avoided on bronze or brass shafts, rods, plungers, or sleeves?
- 416.Less scale formation occurs in a flash evaporator than in a submerged tube evaporator because __________.
- 417.As a rule of thumb, when pressure is applied to hydraulic oil, the oil will __________.
- 418.The inner bottom of a ship is the __________.
- 419.When listed by pitch, which of the hacksaw blades listed would be the most suitable for cutting thin tubing?
- 420.Vessel propellers are classified as being right hand or left hand. A right hand propeller turns clockwise when viewed from __________.
- 421.Which of the listed reasons could cause frost to form on the suction line of a refrigeration compressor?
- 422.To properly remove packing from a valve stuffing box, you should use a __________.
- 423.The primary reason low pressure evaporators produce distillate more efficiently, and with less scale formation, than high pressure evaporators is __________.
- 424.The outer strake of the inner bottom on each side of the ship is called the __________.
- 425.The rubber bladder or separator bag installed in a hydraulic accumulator should only be filled with __________.
- 426.When drilling holes larger than 1/2 inch, a smaller pilot hole should be drilled first to __________.
- 427.If the refrigeration compressor crankcase is sweating, the cause may be due to __________.
- 428.Copper coil tubing is best cut with a __________.
- 429.When normal operating pressure is applied to the hydraulic oil used in a high-pressure system, the oil __________.
- 430.In a longitudinally framed ship, the longitudinal frames are held in place and supported by athwart ship members called __________.
- 431.Which of the listed components of a hydraulic system would enable the pump to be temporarily shutdown, and yet still provide an instantaneous source of hydraulic force?
- 432.To cut angle iron and heavy pipe with a hand hacksaw, you should use a blade with what number of teeth per inch?
- 433.If the suction line between the evaporator and compressor is frosting up, the cause may be due to the thermal expansion valve __________.
- 434.Most solenoid valves are actuated by __________.
- 435.Increased internal leakage, in addition to poor hydraulic system response, and inadequate lubrication, is the result of __________.
- 436.The structural members of the hull extending in a fore and aft direction are called __________.
- 437.The minimum number of crew members permitted by law to operate your vessel can be determined by checking the __________.
- 438.When there is no movement of the rams on an electro-hydraulic steering gear, the tilting box of the running pump is __________.
- 439.If a refrigeration compressor crankcase is sweating, the trouble could be caused by __________.
- 440.Which characteristic or condition will have the greatest effect on increasing a hydraulic oil's viscosity?
- 441.In merchant ship construction, the term 'scantlings' refers to the __________.
- 442.Before boring a blind tapered hole, a good shop practice to follow is to __________.
- 443.When coming to the end of a cut using a hand hacksaw, you should __________.
- 444.Rotation of the steering wheel on the navigation bridge initiates oil pressure being applied to the steering gear rams by __________.
- 445.Frosting or sweating of the suction line of a reciprocating refrigeration compressor indicates a condition which could result in severe damage due to __________.
- 446.A knocking sound from one cylinder of an operating air compressor indicates __________.
- 447.Sluggish response or action of the hydraulic actuators may be a result of __________.
- 448.The purpose of an accumulator in a hydraulic system is to __________.
- 449.A swing check valve is used in a pipeline to __________.
- 450.When the desired rudder angle is attained by a typical double ram electro-hydraulic steering gear, the __________.
- 451.A refrigeration system compressor crankcase is sweating or unusually cold. This is an indication of __________.
- 452.A hacksaw blade will start a cut more easily if you __________.
- 453.Operating a rotary pump at speeds in excess of design requirements could cause __________.
- 454.A solenoid, direct-acting, three-position, spring-centered, directional control valve is used in a hydraulic system to control a linear actuator. Midway through extension, the push button is released, but the actuator continues to extend slowly. Which of the following conditions represents the possible cause?
- 455.In ship construction, structural hull members installed athwart ship are __________.
- 456.In accordance with the Coast Guard Regulations (46 CFR), which of the following situations requires an official logbook entry and is considered the responsibility of the chief engineer?
- 457.When the helm demands a 20° right rudder movement from an electro-hydraulic steering gear, which of the listed actions will be the FIRST action to happen when this rudder position is attained?
- 458.Refrigeration system compressor crankcase sweating is an indication of __________.
- 459.A solenoid direct-acting three-position spring-centered directional control valve is used in a hydraulic system to control a linear actuator. When the remote push button is depressed to extend the actuator it fails to move, even though the pump is in operation. Which of the following statements represents the cause?
- 460.A vertical shaft having a rudder attached to its lower end and having a yoke, quadrant, or tiller fitted to its upper portion by which it may be turned, is the __________.
- 461.Which bearing will carry the load on two small points diametrically opposite to each other?
- 462.The notation '10-24 tap' appears on a drawing. The number "24" indicates the __________.
- 463.To charge a bladder type hydraulic accumulator __________.
- 464.Sweating of the refrigeration system compressor crankcase is caused by __________.
- 465.An increase in rotor clearances in a rotary pump will __________.
- 466.Air entrained in the hydraulic fluid, or trapped in an actuator will cause the actuators to move with a jerky motion. This action is a result of __________.
- 467.The mutual action between parts of a material to preserve their relative positions when external loads are applied to the material, which tends to resist deformation when subjected to external forces, is known as __________.
- 468.In an electro-hydraulic steering system, rudder movement is maintained in close synchronization with the steering wheel position by means of the __________.
- 469.Crankcase sweating in a refrigeration system is caused by __________.
- 470.The letters 'NC' in '1/4-20 NC' indicates the bolt is __________.
- 471.Air trapped in one end of a hydraulic actuator may be indicated by __________.
- 472.Which of the following statements is true concerning the instrumentation or alarms provided at the main control station for an automated main propulsion plant?
- 473.A chief engineer's responsibilities include making logbook entries whenever fuel oil is received. In accordance with Coast Guard Regulations (46 CFR), this log entry must include the __________.
- 474.If a refrigeration system compressor crankcase is sweating, you should __________.
- 475.A P-type trap and drain is used __________.
- 476.When new piping sections have been fabricated for installation in a hydraulic system, prior to installation the piping should be __________.
- 477.A cofferdam is a/an __________.
- 478.If the drill point lips are ground at different angles, the drill will __________.
- 479.Proper hacksaw cutting is accomplished when pressure is applied only on the __________.
- 480.Before performing any maintenance on a hydraulic system storing energy in an accumulator, you should __________.
- 481.The term '5/16-24' describes __________.
- 482.A multistage centrifugal pump can be BEST described as having __________.
- 483.The major difference between the discharge and suction valves installed in most low pressure, reciprocating air compressors is that __________.
- 484.If you attempt to tighten a leaking hydraulic fitting with pressure on the system, you will __________.
- 485.The annual re-inspection of a tank vessel, holding a two year Certificate of Inspection endorsed, 'Inspected and Approved for the Carriage of Flammable or Combustible Liquids of Grade A', must __________.
- 486.Propeller pitch speed minus ship speed divided by the propeller pitch speed is termed __________.
- 487.As sometimes utilized with centrifugal pumps operating with a high suction lift, foot valves are primarily designed to __________.
- 488.Which of the devices listed, when used on an electro-hydraulic steering gear, keeps the movement of the rudder closely in step with the steering wheel?
- 489.The sensible heat of air is dependent upon the __________.
- 490.What should be done if localized scoring is discovered on a pump shaft sleeve during routine maintenance inspection?
- 491.The designation '1/4-20' describes __________.
- 492.Which of the following statements represents the path of air flow passing through a typical two stage, low pressure, reciprocating, air compressor?
- 493.In accordance with Coast Guard Regulations (46 CFR), the hailing port marked on the stern of a vessel indicates __________.
- 494.Differential pistons used in some reciprocating air compressors, serve to provide __________.
- 495.Before doing any work on a hydraulic system equipped with accumulators, you should __________.
- 496.Which of the problems listed could cause erosion of the expansion valve disks and seats?
- 497.A pump shaft that is bent or distorted should normally be __________.
- 498.The quantity and density of brine discharged from the last effect of a flash type evaporator should be kept at a constant value so as to __________.
- 499.If an air compressor is used to supply compressed air to outlets throughout the engine room and on deck of a vessel, the system is known as the __________.
- 500.An international and coastwise load line assignment and certificate has been issued to a vessel by the American Bureau of Shipping, under the authority of Coast Guard Regulations (46 CFR), for a period of __________.