USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 17
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1601.According to Coast Guard regulations (46 CFR Part 92), a standard fire test is one __________.
- 1602.If the superheat value of the thermostatic expansion valve is adjusted too high the __________.
- 1603.Sawing faster than a rate of 40 to 50 strokes per minute while using a hand held hacksaw will generally __________.
- 1604.In an air conditioning system, moisture is removed from the air by __________.
- 1605.What maintenance may be carried out on a thermostatic expansion valve?
- 1606.Which statement about calibrating a newly installed thermostatic expansion valve is correct?
- 1607.Which of the files listed can be used for sharpening a tool?
- 1608.When using a hand held hacksaw the correct maximum rate of speed for cutting should be __________.
- 1609.Routine maintenance on a Central Control Room hermetically sealed air conditioning unit should include __________.
- 1610.When a thermostatic expansion valve is installed in a container refrigeration system, the sensing bulb may not require insulation if the bulb is installed __________.
- 1611.The type of tooth set on a hacksaw blade where every third tooth remains straight, while the other two are alternately set is known as __________.
- 1612.Which of the following alarms and instrumentation is not required for a vessel incorporating a controllable pitch propeller in its main propulsion system?
- 1613.Each pressure vessel containing refrigerants, which may be isolated, shall be __________. (46 CFR)
- 1614.The type of tooth set on a hacksaw blade where two adjoining teeth are staggered to the right, then two to the left, and continue to alternate in this manner is known as __________.
- 1615.Expansion valve maintenance should include which of the following procedures?
- 1616.Which of the installation steps listed is necessary for the proper operation of the thermostatic expansion valve?
- 1617.Which of the following statements is correct concerning requirements for propellers?
- 1618.Which of the following statements is correct concerning the regulations (46 CFR) regarding internal combustion engine exhausts, boiler and galley uptakes, and similar sources of ignition?
- 1619.The latent heat of water vapor in air is dependent upon the __________.
- 1620.When replacing a thermostatic expansion valve sensing bulb, it is necessary to __________.
- 1621.A hacksaw blade will break if __________.
- 1622.Hydraulic hose assemblies are permitted by 46 CFR to be installed between two points of relative motion __________.
- 1623.The vessel has received a refrigerated container loaded with 9 long tons of ice cream. The current box temperature is 31°F but has a normal set point of minus 10°F. Under ideal conditions how long will it take to pull the box temperature down to set set point, if the equipment is operating properly? (Specific heat of the cargo equals 0.39 BTU/LB/°F, with a container heat gain of 6,000 BTU/hr, and a refrigeration system capacity of 3.5 tons)
- 1624.Rather than design an infinite variety of valve sizes for use as thermostatic expansion valves, some manufacturers use __________.
- 1625.Constant superheat is maintained at the evaporator outlet of a refrigeration coil by a __________.
- 1626.Edges on objects not visible in the view shown are represented in blueprints by __________.
- 1627.During the operation of a large multi-box refrigeration system, using a fixed capacity compressor, only two of the five boxes are in the process of actively being cooled. If two additional boxes were to be brought into the cooling process simultaneously, the __________.
- 1628.If a refrigeration system is overcharged with refrigerant, one result will be __________.
- 1629.During the operation of a five box refrigeration system, using a fixed capacity compressor, two additional boxes came on line with the two boxes already in the active cooling process. At the beginning of the cooling period for the two additional boxes, the operating conditions of the system would require the quantity (flow rate) of refrigerant to the compressor suction to__________.
- 1630.A liquid is being transferred by a centrifugal pump. As the liquid passes through the volute, its velocity decreases and __________.
- 1631.The watch engineer finds the cargo refrigeration compressor has blown the shaft seal. In this situation, he should __________.
- 1632.It is necessary to replace a branch suction section of bilge system piping within the machinery space. The machinery space is 100' in length and 85' in breadth. The molded depth of the bulkhead deck is 25'. Which of the listed pipe sizes should be used?
- 1633.Protective equipment to be used while carrying out oxy-acetylene welding should always include __________.
- 1634.When the refrigeration system compressor suction pressure corresponds to an elevation in coil temperature, a low pressure cutout switch is set to automatically start the compressor. The normal stopping point of the compressor is set by adjusting the __________.
- 1635.In an emergency, the electro-hydraulic steering units can be directly controlled by the __________.
- 1636.Which nondestructive testing method is suitable for use in detecting and identifying a diameter subsurface void in a six inch diameter stainless steel shaft?
- 1637.One function of the thermal expansion valve is to __________.
- 1638.The safety heads of most large reciprocating compressors used in refrigeration systems are held in place by __________.
- 1639.Dry bulk material transfer to an offshore drilling rig has just begun when you discover air leaks at the P-tank manhole cover. You must __________.
- 1640.While cleaning out a P-tank __________.
- 1641.At ambient temperature and atmospheric pressure, R-12 is a/an __________.
- 1642.Which chemical symbol represents ammonia?
- 1643.If a vessel is not provided with duplicate service systems, which of the systems listed will satisfy the regulations if serviced by two pumps? (46 CFR)
- 1644.A centrifugal pump gradually develops insufficient discharge pressure. What corrective action is required?
- 1645.The low pressure cutout switch will cause the compressor in a refrigeration system to short cycle if the __________.
- 1646.Which piping material is recommended to be used in extra heavy duty sizes in ammonia refrigeration system construction?
- 1647.When cleaning out a P-tank __________.
- 1648.If your skin comes in contact with liquid ammonia refrigerant, you should immediately __________.
- 1649.It is necessary to test the hydraulic system of a controllable pitch propeller. According to 46 CFR what should be done?
- 1650.Which materials should be used for ammonia refrigeration system evaporator cooling coil construction?
- 1651.When checking the oil level in a refrigeration compressor, the most accurate reading is obtained __________.
- 1652.If an evaporator or condenser coil of a container refrigeration system becomes dirty and requires cleaning, one of the suggested methods is to use the __________.
- 1653.Ammonia is lighter than air and if a leak should occur its concentration will be __________.
- 1654.When cleaning a P-tank __________.
- 1655.The pressure in a high pressure refrigeration system about to be opened for repair should be __________.
- 1656.The temperature in a refrigerated space is controlled by adjusting the thermostat connected to the __________.
- 1657.Standard driers used in many container type refrigeration systems may contain __________.
- 1658.If the temperature of the ammonia gas in the discharge piping and the condenser of a refrigeration system remains above 266°F, the __________.
- 1659.The flame of a sulphur candle in the presence of an ammonia leak will turn __________.
- 1660.When manually cleaning a P-tank __________.
- 1661.According to Coast Guard Regulations (46 CFR) an accumulator is a/an __________.
- 1662.Which of the following devices is the safest to use when locating ammonia leaks?
- 1663.The water regulating valve installed in a refrigeration system is operated by the __________.
- 1664.Which of the following refrigerants will normally require water cooled compressor components?
- 1665.The receiver used in a refrigeration system __________.
- 1666.Average condensing pressures of an ammonia refrigeration system range between __________.
- 1667.An ammonia leak will turn moistened pink litmus paper __________.
- 1668.The thermal expansion valve reacts directly to the __________.
- 1669.Under normal conditions ammonia refrigerants should be added at the __________.
- 1670.To service a 60 ton air conditioning package, the easiest way to determine the type of refrigerant used is to __________.
- 1671.Pure anhydrous ammonia is considered non-corrosive to __________.
- 1672.If auxiliary machinery vital to the main propulsion system is not provided with independent duplicate systems, which of the systems listed would satisfy regulations if serviced by two pumps? (46 CFR)
- 1673.When used as a refrigerant, ammonia containing moisture will act as a corrosive mixture to __________.
- 1674.When hot gas defrosting a refrigeration system, one way to overcome the possibility of a large slug of liquid refrigerant entering the compressor suction is to use the installed __________.
- 1675.If the combination moisture indicator and sight glass indicates an accumulation of moisture within the system, which of the listed procedures would be the most practical to follow?
- 1676.Which of the listed valves should be closed when adding ammonia to a refrigeration system?
- 1677.Which refrigeration system will require the use of an oil trap?
- 1678.The distillate pump for a 10000 GPD evaporator, should be rated at a minimum of __________.
- 1679.A flapper valve, also known as a beam valve, is frequently used in refrigeration compressor discharge valves, and is designed to __________.
- 1680.Refrigerant recovery equipment that is considered as being system dependent __________.
- 1681.A P-tank system, as used on oilfield supply boats __________.
- 1682.The suction pressure switch controlling the refrigeration compressor operation is actuated by __________.
- 1683.Refrigerant entering the compressor of a refrigeration system should be in which of the following conditions?
- 1684.Inhalation of high concentrations of CFCs may have which of the following effects?
- 1685.The chemical formula for ozone is represented as __________.
- 1686.R-12 has been a suitable refrigerant for use in high temperature applications with __________.
- 1687.When taking readings at the suction service valve of an operating refrigeration compressor __________.
- 1688.Refrigerant leaving the metering device in a refrigeraton system is a __________.
- 1689.Operating pressure on a P-tank system should be __________.
- 1690.If you know that a refrigeration system is leaking refrigerant, you would first___________.
- 1691.Which of the devices listed will indicate the proper operation of a refrigeration system dryer?
- 1692.Which of the following base oils cannot be refined without developing a change in chemical composition?
- 1693.Large quantities of halogenated floro-carbons when released from refrigeration systems, will contribute to ozone depletion in the __________.
- 1694.Which can be considered as a drop-in replacement refrigerant?
- 1695.In a multi-evaporator refrigeration system, a solenoid valve is installed in the liquid line before __________.
- 1696.Industrial process and commercial CFC type refrigeration equipment with annual leak rates of 35% or more, require leak repair of the system if it contains a refrigerant charge of more than __________.
- 1697.A light dust trail from the storage tank vent, plus a fluctuating P-tank pressure and constant movement of the material discharge hoses indicates __________.
- 1698.A boiler forced draft pressure gage indicates nine (9) inches of water. This corresponds to a pressure of __________.
- 1699.The liquid line, thermostatically controlled, solenoid valve is operated in response to the __________.
- 1700.Most freon refrigerants are originated primarily from which of the following base molecules?