USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 30
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 2901.Some centrifugal pumps have water lines connected to the stuffing box glands to __________.
- 2902.If you have a duplex double acting reciprocating pump making 100 strokes/minute, with a 6" diameter cylinder, a 8" stroke and operating with 90% volumetric efficiency, what is the capacity of this pump?
- 2903.If you have a simplex single acting reciprocating pump making 150 strokes/minute, with a 3" diameter cylinder, a 5" stroke and operating with 92% volumetric efficiency, what is the capacity of this pump?
- 2904.If you have a simplex single acting reciprocating pump making 180 strokes/minute, with a 5" diameter cylinder, a 8" stroke and operating with 87% volumetric efficiency, what is the capacity of this pump?
- 2905.If you have a simplex single acting reciprocating pump making 150 strokes/minute, with a 6" diameter cylinder, a 13" stroke and operating with 95% volumetric efficiency, what is the capacity of this pump?
- 2906.According to 46 CFR Part 56, carbon steel bolts rather than alloy steel bolts may be used to make up a flange if the normal operating __________.
- 2907.The chemical substance initially responsible for heat loss in the combustion process is __________.
- 2908.The surging that occurs in a centrifugal air conditioning compressor is a result of __________.
- 2909.Refrigerants that may experience fractionation are identified as blends of __________.
- 2910.If you have a simplex single acting reciprocating pump making 150 strokes/minute, with a 4" diameter cylinder, a 7" stroke and operating with 91% volumetric efficiency, what is the capacity of this pump?
- 2911.If you have a duplex double acting reciprocating pump making 140 strokes/minute, with a 3" diameter cylinder, a 9" stroke and operating with 94% volumetric efficiency, what is the capacity of this pump?
- 2912.When air is at its dew point and there is no change in either the temperature or pressure, the air __________.
- 2913.If you have a simplex single acting reciprocating pump making 150 strokes/minute, with a 3" diameter cylinder, a 11" stroke and operating with 95% volumetric efficiency, what is the capacity of this pump?
- 2914.If you have a duplex single acting reciprocating pump making 270 strokes/minute, with a 4" diameter cylinder, a 7" stroke and operating with 81% volumetric efficiency, what is the capacity of this pump?
- 2915.Which non-ferrous alloy is most commonly used for heat exchanger tubes and possesses a high resistance to corrosion?
- 2916.The major difference to consider when selecting a P-type or S-type lavatory drain trap would be the __________.
- 2917.If you have a simplex single acting reciprocating pump making 180 strokes/minute, with a 5" diameter cylinder, a 6" stroke and operating with 87% volumetric efficiency, what is the capacity of this pump?
- 2918.In a refrigeration system, the amount of superheat absorbed by the refrigerant is adjusted at the __________.
- 2919.A hacksaw blade will start a cut more accurately if you __________.
- 2920.Rapid fluctuations of absolute pressure in the last effect of a multi-effect submerged tube distilling plant will tend to cause __________.
- 2921.If you have a simplex single acting reciprocating pump making 160 strokes/minute, with a 6" diameter cylinder, a 12" stroke and operating with 97% volumetric efficiency, what is the capacity of this pump?
- 2922.For most multi-box refrigeration systems, the liquid line sight glass would be located __________.
- 2923.If you have a simplex single acting reciprocating pump making 160 strokes/minute, with a 4" diameter cylinder, a 12" stroke and operating with 85% volumetric efficiency, what is the capacity of this pump?
- 2924.If you have a duplex single acting reciprocating pump making 100 strokes/minute, with a 6" diameter cylinder, a 4" stroke and operating with 90% volumetric efficiency, what is the capacity of this pump?
- 2925.The tool used to make up connection fittings for small diameter copper tubing is called a/an __________.
- 2926.The thermal bulb of an expansion valve that is attached to the evaporator tail coil should be __________.
- 2927.If you have a simplex single acting reciprocating pump making 150 strokes/minute, with a 7" diameter cylinder, a 13" stroke and operating with 95% volumetric efficiency, what is the capacity of this pump?
- 2928.If you have a duplex double acting reciprocating pump making 170 strokes/minute, with a 4" diameter cylinder, a 11" stroke and operating with 89% volumetric efficiency, what is the capacity of this pump?
- 2929.Which CFR provides information that pertainins to sea valve inspections during a vessel drydocking?
- 2930.Increasing the speed of a centrifugal pump will result in an increase in the pump capacity. Another means of increasing the total head pressure of a centrifugal pump is to increase the __________.
- 2931.The steam coils in a high pressure contaminated evaporator used in a steam plant should be descaled with __________.
- 2932.Prior to making repairs on an R-12 refrigeration system, if system leaks prevent reaching the required levels of evacuation for recovery of refrigerant, you will need to ________.
- 2933.During the normal operation of a soloshell double-effect distilling unit, what is flowing through the tubes of the first effect vapor feed heater?
- 2934.Which of the listed components would normally be installed with a Control Air System pressure regulator?
- 2935.While inspecting the steering system at sea, you should check for __________.
- 2936.Which of the following statements describes the operation of a three-way solenoid trip/dump valve on a two stage flash-type evaporator?
- 2937.The safety device which normally stops the refrigeration compressor before the relief valve starts to open is the __________.
- 2938.If the flow of water from a centrifugal pump is allowed to be stopped by closing the discharge valve while the pump continues to run for an extended period, which of the following will occur?
- 2939.A characteristic of lubricating oil which causes additional centrifuging requirements for proper purification is __________.
- 2940.The torque rating of a fluid power motor is expressed in __________.
- 2941.When the hydraulic control lever for a deck winch is placed in the neutral or off position, the spring set brake on the fluid motor drive shaft is __________.
- 2942.When using a portable droplight, you should always insure that the __________.
- 2943.Early models of the flash-type evaporators required a pump to drain the steam condensate from the salt water feed heater. This pump would normally discharge to the __________.
- 2944.The probable cause of erratic operation of a pneumatically controlled steam pressure reducing valve is __________.
- 2945.Operation of a hydraulic pump in a cavitating condition can cause __________.
- 2946.What equipment is required when processing bilge slops for overboard discharge?
- 2947.HCFC-22 has been recovered from a refrigeration system during replacement of the condenser. This refrigerant can be __________.
- 2948.A compressor operating with an accumulation of dust and grease on the surfaces of an intercooler would result in __________. I. the motor to run warmer than usual II. the second stage would operate at a higher temperature
- 2949.Some of the hazards associated with air-operated power tools may be avoided if the operator would __________.
- 2950.The definition of superheat refers to the amount of heat a substance contains and applies to __________. I. vapors II. Solids
- 2951.According to 46 CFR, the tailshafts of a twin screw ocean going vessel must be examined and inspected in the presence of a marine inspector __________.
- 2952.Hot water system heat exchangers are selected for the heating load required plus about 50% excess capacity to allow for __________.
- 2953.If increasing the cooling water flow to a refrigeration condenser fails to lower the condenser pressure, the probable cause may be due to __________.
- 2954.One disadvantage of using a mechanical shaft seal instead of mechanical packing is that _________.
- 2955.When installing a mechanical shaft seal on a pump, it is important to __________.
- 2956.The most likely reason for premature failure of a pumps mechanical shaft seal is __________.
- 2957.It requires 151 HP to operate a centrifugal pump having a 14.75 inch impeller at 1800 RPM, at a capacity of 2250 GPM with a 218 foot head. If during an overhaul of the pump, the impeller diameter is reduced to 14 inches, the capacity of the pump operating at the same RPM would be __________.
- 2958.It requires 151 HP to operate a centrifugal pump having a 14.75 inch impeller at 1800 RPM, at a capacity of 2250 GPM with a 218 foot head. If during an overhaul of the pump, the impeller diameter is reduced to 14 inches, the discharge head of the pump operating at the same RPM would be __________.
- 2959.It requires 151 HP to operate a centrifugal pump having a 14.75 inch impeller at 1800 RPM, at a capacity of 2250 GPM with a 218 foot head. If during an overhaul of the pump, the impeller diameter is reduced to 14 inches, the horsepower requirement to operate at the same RPM would be __________.
- 2960.All portable electric tools should have a ground connection to prevent __________.
- 2961.When a rotating engine shaft frequency and the natural harmonic vibration frequency become synchronized at a particular speed, that speed is known as the __________.
- 2962.According to 46 CFR Part 91, a temporary Certificate of Inspection, Form CG-854, may be issued to a self propelled cargo vessel __________.
- 2963.Liquid line gas in a refrigeration system may cause erosion of the expansion valve's internal components and could cause the valve to __________.
- 2964.According to 46 CFR Part 58, when installing a new independent fuel tank for the emergency lighting generator, which of the following statements must be strictly adhered to in accordance with Coast Guard Regulations?
- 2965.According to 46 CFR Part 91, which of the following statements concerning a vessel's Coast Guard Certificate of Inspection and associated inspections is correct?
- 2966.According to 46 CFR Part 61, what is the maximum allowable permitted wear on a stern tube bushing for a vessel that has its propelling machinery located amidships, with a water lubricated stern tube bearing carrying a 12 inch diameter shaft?
- 2967.If it becomes necessary to start an axial piston hydraulic motor under conditions where the hydraulic fluid is colder than the lowest temperature recommended for proper operation, you should operate the system at __________.
- 2968.According to regulations (46 CFR Part 58), a boiler combustion control system may be tested at __________.
- 2969.In a typical hydraulic steering gear system, as the designated rudder angle is approaching the helm command angle, what will be the reaction of the steering gear follow-up mechanism?
- 2970.A vessel has a mean draft of 28 feet 08 inches before taking bunkers. What will be the final aft draft after taking on nine hundred tons of fuel oil, if the TPI immersion is 50 and the final forward draft is 30 feet 00 inches?
- 2971.Which of the following best describes the adiabatic pressure/volume relationship with regards to a fixed amount of a saturated gas?
- 2972.Which of the following statements is true concerning centrifugal pumps?
- 2973.Coast Guard Regulations (46 CFR Part 56) require all power-operated valves, other than those opened against spring force, to have an energy storage system. That energy storage system shall be capable of __________.
- 2974.Ship's bulkheads are reinforced against bending and bulging with the addition of __________.
- 2975.A one ton air conditioning system has which of the listed operating characteristics?
- 2976.A squealing sound generated by a reciprocating air compressor upon starting may indicate __________.
- 2977.In an air conditioning system, low discharge head pressure associated with a reciprocating compressor can be the result of __________.
- 2978.The open end wrench size for a 3/4 inch American National Standard hex head machine bolt is __________.
- 2979.When cutting with a handheld hacksaw, you should apply downward pressure on the hacksaw frame __________.
- 2980.One function provided by a hydraulic accumulator is to __________.
- 2981.Which chemical, when released into the atmosphere, has been found to eventually reach the stratosphere and react unfavorably with the earths ozone layer?
- 2982.If the drive belts on an air compressor were squealing during startup, you should __________.
- 2983.Machinery vibration sensing devices are commonly identified as __________.
- 2984.A machinery vibration monitoring program can be used to identify bearing defects by __________.
- 2985.In terms of metric pressure conversion, an absolute pressure of 1 "bar" would be approximately equal to what value "psia"?
- 2986.When converting metric pressure values, an absolute pressure of 7 "bars" would be approximately equal to what value of "psia"?
- 2987.In terms of metric pressure conversion, approximately what value of "psi" equals one "bar"?
- 2988.The action of water circulating within a natural circulation boiler, is the direct result of __________.
- 2989.Which of the conditions listed represents the greatest effect of excess frost accumulation on evaporator coils in a refrigeration system?
- 2990.Which of the following forms of energy concerns the forces which bind atoms together in a molecule?
- 2991.A stop-check valve is a type of check valve that __________.
- 2992."Prussian Blue" is commonly used __________.
- 2993.A Reed and Prince screwdriver should be used only on a Reed and Prince screw, and a Phillips screwdriver should only be used on a Phillips screw in order to avoid damaging the __________. I. tool II. screwhead
- 2994.A "barrel" is defined as a unit of liquid, measured at 60°F, and is equivalent to __________.
- 2995.After installing a new hydraulic pump in a system, what special attention should be given to the hydraulic system?
- 2996.Which units of measurement are commonly used to express pump suction head values when calculating pump capacities and hydraulic horsepower?
- 2997.Which of the following is not part of the high side of a refrigeration system?
- 2998.Cylinder inlet valve failure in a low pressure air compressor can be caused by __________.
- 2999.An emergency bilge suction is required for __________.
- 3000.Which type of pump would normally be used to tranfer fairly large quantities of fluids at relativley low pressures?