USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 2
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 101.The exposed portion of the outboard propeller shaft is protected against seawater corrosion by __________.
- 102.Why are removable sleeves installed on centrifugal pump shafts?
- 103.A good quality oil used in main propulsion engine lubrication systems should be __________.
- 104.When air at a given temperature, contains the maximum amount of moisture for that temperature, the air is said to be __________.
- 105.Which of the listed types of pumps is NOT likely to be installed in a main drainage or evacuation system?
- 106.In a compression type automatic grease cup, the lubricant is forced into the bearing by __________.
- 107.The term referring to the number of teeth per inch on a hacksaw blade is known as the __________.
- 108.Which of the following statements represents the advantage of rotary pumps as compared to reciprocating pumps?
- 109.Which of the following terms represents the form of heat removed from the refrigerant in the condenser of a refrigeration system?
- 110.Which of the devices listed should be used to reshape a grinding wheel?
- 111.Water leaking through the stern tube stuffing box is used to accomplish which of the following actions?
- 112.Water hammer in a steam heating system can be caused by __________.
- 113.Main propulsion engine lube oil sumps should be constructed __________.
- 114.A major controlling factor in the location of the condensate return piping from a heating system is/are __________.
- 115.If the existing vapor pressure is subtracted from the indicated pressure at the pump suction, the remainder is the __________.
- 116.A first stage unloader installed in a low pressure air compressor is unable to completely retract. This will result in __________.
- 117.The heat removed from the refrigerant in the condenser of a refrigeration plant is the __________.
- 118.When conducting a hydrostatic test on the distillate cooler shell of a flash type evaporator, liquid appears well inside one of the tubes. In order to correct this, you should __________.
- 119.Excessive leakage and premature failure of valve packing is a result of __________.
- 120.Which of the following problems may be encountered by using an oil having a viscosity higher than that specified for an operating hydraulic system?
- 121.Water leaking from a pump packing gland is kept away from the bearing housing by the use of __________.
- 122.An inadequate reciprocating bilge pump discharge is most often caused by __________.
- 123.Which of the listed problems could produce a high absolute pressure within a flash type evaporator?
- 124.Which of the following conditions should be used to support the need to change the lube oil when there has been an increase in the neutralization number?
- 125.The dew point of air is reached when the wet bulb temperature is __________.
- 126.The purpose of bilge keels is to __________.
- 127.A casing drain is provided for axial piston and bent axis variable stroke pumps to __________.
- 128.Before the longitudinal carriage feed of a lathe is engaged, you must be certain the __________.
- 129.Increasing the speed of a rotary pump above its rated speed will result in which of the following conditions to occur?
- 130.The function of lubricating oil is to __________.
- 131.The tendency for lubricating oil to thin out at high temperatures and thicken at low temperatures will be characterized by a __________.
- 132.After packing is added to the stern tube stuffing box, which of the following procedures should be observed to insure even tightening of the gland?
- 133.The temperature at which water vapor in the atmosphere begins to condense is called the __________.
- 134.One function of the air receiver in a compressed air system is to __________.
- 135.If a drill press is used to completely bore through a metal plate, feed pressure on the drill bit should be eased as the bit breaks through the bottom of the hole to prevent __________.
- 136.Which of the following statements describes the purpose of the split inflatable seal installed aft of the primary seal assembly for the propeller shaft?
- 137.Why should a person who is performing maintenance on an air compressor, wire and tag the system valves closed?
- 138.With regard to the opening and closing of watertight appliances not fitted with a remote operating control or alarm system, which of the following is the master or person in charge of a MODU required to enter in the logbook?
- 139.One of the main differences between the various types of screw pumps is in the __________.
- 140.The FIRST thing to do to ensure that a refrigeration unit will not start while undergoing repairs, is to __________.
- 141.At which of the following locations would a duplex pressure gage most likely be located?
- 142.Why is the discharge pressure of a herringbone gear pump steadier than the discharge pressure of a simple spur gear pump?
- 143.Which of the following actions, pertaining to saltwater lubricated stern tube stuffing boxes, is usually observed when the ship is expected to be in port for an extended period?
- 144.A bourdon tube-type steam pressure gage is fitted with a siphon loop to prevent damage from __________.
- 145.In a refrigeration system, the refrigerant absorbs the latent heat of vaporization in the __________.
- 146.Oil emulsification in engine lubricating oils will tend to __________.
- 147.The conical steel or composition cone installed on a propeller, known as a fairwater cone, provides which of the following benefits?
- 148.The taper produced by a lathe taper attachment is determined by setting the __________.
- 149.The only means of removing the latent heat of condensation from a refrigerant in the normal refrigeration cycle is by __________.
- 150.Which of the listed devices is used to control the admission of steam to the steam cylinder of a reciprocating pump?
- 151.Which of the devices listed prevents water from entering a ship's hull via the propulsion shaft?
- 152.With reference to a vessel's structural integrity, the most significant characteristic of a cryogenic liquid is its __________.
- 153.A boiler forced draft pressure gage indicates 6 inches of water. This corresponds to a pressure of __________.
- 154.To obtain a 1/2 inch per foot taper on an 18 inch work piece, the tailstock of the lathe must be set over __________.
- 155.The heat required to change a substance from a solid to a liquid while at its freezing temperature, is known as the latent heat of __________.
- 156.A wrench that completely surrounds a nut, or bolt head is a/an __________.
- 157.The degree to which the viscosity of an oil will change with a change in temperature is indicated by the __________.
- 158.Which of the listed reciprocating pump parts control the position of the pilot slide valve?
- 159.Which of the following guidelines is considered to reflect good design practices of shipboard steam heating systems?
- 160.The heat required to change a substance from a liquid to a gas without experiencing a temperature change, is defined as the latent heat of __________.
- 161.The average density of brine discharged from the last stage of a fresh water evaporator should not exceed __________.
- 162.A distinguishing feature of an eductor, when compared to other pumps, is the __________.
- 163.When securing a flash-type evaporator for an extended period of time, you should __________.
- 164.The portion of a hydraulic hose that determines its overall strength, is the __________.
- 165.Which features of a centrifugal pump reduce the need for renewing worn impellers and pump casings?
- 166.A centrifugal pump may fail to deliver water when first started if the __________.
- 167.A weight of 1,000 kips is equivalent to __________.
- 168.Which of the devices listed is common to all types of pumps?
- 169.Heat which brings about a change in the physical state of a substance without a change in temperature, is called __________.
- 170.The hulls of most modern towing vessels constructed today are fabricated from __________.
- 171.Which of the listed parts is used in a lobe-type rotary pump to allow for wear on the lobe edges?
- 172.A boiler forced draft pressure gage indicates 8 inches of water. This corresponds to a pressure of __________.
- 173.If a centrifugal pump vibrates and is noisy when operating, the cause could be __________.
- 174.Which of the wrenches listed is least likely to slip off a bolthead or nut?
- 175.Expansion tanks when used in a ships hot water heating system, may be of the open or closed type. In a closed type system, what would be the normal temperature range of the water?
- 176.Latent heat can be defined as the heat which must be added to a substance in order to change it from a __________.
- 177.The designation 'schedule 80 extra strong ' refers to __________.
- 178.Tapping threads into a blind hole should be finished by using a __________.
- 179.The factors that determine the service life of packing in a pump will include which of the following conditions?
- 180.If the capacity of a centrifugal pump decreases gradually over a long period of time, you should replace the __________.
- 181.To absorb the wear resulting from impeller rotation and abrasives in the liquid, a centrifugal pump is usually fitted with __________.
- 182.Personnel working with refrigeration systems, and subject to the exposure of refrigerants should wear __________.
- 183.The ability of a metal to be hammered, or rolled out is called its __________.
- 184.A pressure reading of 00.0 psig is theoretically equal to __________.
- 185.If the foundation bolts of a reciprocating air compressor are loose, which of the conditions below will occur?
- 186.Gate valves should not be used for throttling as __________.
- 187.To finish tapping a blind hole, it is best to use a __________.
- 188.The purpose of an air compressor unloading device is to __________.
- 189.The amount of moisture in a given sample of air, when compared with the amount of moisture the air could hold if totally saturated at the existing temperature of the sample, is called __________.
- 190.Which of the copper alloys listed is commonly used in heat exchangers and possesses a high resistance to corrosion?
- 191.Anti-friction bearings can be removed undamaged from a shaft by using an arbor press, or wheel puller with a __________.
- 192.Which of the following statements is correct relative to distillation plant operation?
- 193.A leaking steam trap located in the return lines from a heating system is indicated by excessive __________.
- 194.If a centrifugal pump is driven by a constant speed electric motor and produces a discharge pressure less than designed, the cause is probably __________.
- 195.The ratio of the weight of moisture contained in a given volume of air, to the weight of moisture that the same sample would hold if saturated, is called the __________.
- 196.Which of the listed chemicals can be routinely used to maintain the hygienic quality of potable water?
- 197.Which of the following statements concerning anti-friction bearings installed on pumps is true?
- 198.The steam coils in a high pressure evaporator used for saltwater service should be descaled with __________.
- 199.The packing installed in the pump stuffing box is normally lubricated by __________.
- 200.A lathe dog, fitted with a headless set screw, is known as a __________.