USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 12
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1101.Coast Guard Regulations (46 CFR) require the emergency bilge system to __________.
- 1102.Excessive air leakage into the suction side of a centrifugal pump would be indicated by which of the following operational problems?
- 1103.A mode of control, whereby the position of the final control element is linearly proportional to the rate of change of the controlled variable, is called __________.
- 1104.A dented race in an antifriction bearing could be caused by __________.
- 1105.While inspecting the steering system at sea, you should check for __________.
- 1106.How does the viscosity of a fluid being pumped affect the operation of a spur gear pump?
- 1107.If one box in a multiple box, direct expansion type refrigeration system was experiencing an excessively low temperature, this could be a result of __________.
- 1108.When securing an oxyacetylene cutting outfit for an extended period, you should close the __________.
- 1109.Pump efficiency may be lost as a result of __________.
- 1110.A mode of control, whereby the speed of motion of the final control element is linearly proportional to the deviation of the controlled variable from set point, is called __________.
- 1111.A solenoid, direct-acting, three-position, spring-centered, directional control valve is used in a hydraulic system to control a linear actuator. With the actuator under load there is no movement. However, when the load is removed, the actuator can be cycled in both directions, although slower than normal. Which of the statements listed is the probable cause?
- 1112.The capacity of a centrifugal pump can be increased by the installation of a larger diameter impeller. Another means of increasing the pump capacity is to __________.
- 1113.While inspecting the steering gear at sea, you should check for __________.
- 1114.A spur gear pump should be operated with the discharge valves __________.
- 1115.Leaking suction valves in a refrigeration compressor are indicated by __________.
- 1116.In an oxygen acetylene welding outfit, the torch tip orifice size __________.
- 1117.Which of the following conditions would be hazardous if you were using two centrifugal pumps to discharge a flammable liquid?
- 1118.Greases are generally produced by __________.
- 1119.The oil in a cargo winch gear box should be sampled periodically to __________.
- 1120.When the steering gear is in operation, you should __________.
- 1121.What class of screw thread is indicated with a machine screw described as 1/2-13 NC-2?
- 1122.The capacity of a rotary pump, delivering a constant viscosity fluid, will decrease when the discharge pressure is increased, due to __________.
- 1123.Which of the following forms of energy is usually associated with the motion of large bodies or objects?
- 1124.A refrigeration system is equipped with a reciprocating compressor and a water cooled condensing unit. If the system is overcharged, the resulting high head pressure will be caused by __________.
- 1125.If it were necessary for you to frequently replace the packing on the main condensate pump, the trouble could be the result of __________.
- 1126.Which indicator is used to determine the hardness of a grease?
- 1127.Winch gears must be maintained in proper alignment to prevent __________.
- 1128.If a hydraulic pump is producing a noisy whine when in operation, the cause may be __________.
- 1129.When using a deflecting beam torque wrench, the torque is __________.
- 1130.The capacity of a gear type rotary pump, when operated at a constant speed, will decrease with an increase in the pump __________.
- 1131.An excessive charge of refrigerant in an air-cooled refrigeration system can cause __________.
- 1132.With reference to the oxyacetylene welding of high carbon steels, hard-facing, and the welding of nonferrous alloys, such as monel, the best flame to use is termed a/an __________.
- 1133.Excessive wear on a centrifugal pump shaft sleeve will __________.
- 1134.Who is responsible for completing the Muster List ("Station Bill") or muster list and posting it in a visible area aboard the vessel?
- 1135.Inspection of a low pressure gear pump for cavitation will usually be indicated by a wear pattern __________.
- 1136.When renewing sections of pipe in a hydraulic system, the nominal pipe size of the piping always indicates the __________.
- 1137.The output volume of a positive fixed displacement pump can be changed only by __________.
- 1138.Which of the conditions listed may be an indication of an excessive amount of refrigerant circulating through the system?
- 1139.Excessive wear on a centrifugal pump shaft sleeve will __________.
- 1140.The mode of control employed by a typical bilge alarm circuit is a __________.
- 1141.If you are given the job of adding hydraulic fluid to a mooring winch, and are not certain as to the type of fluid to use, you should __________.
- 1142.A gradual decrease in the discharge pressure of an operating hydraulic pump can be caused by __________.
- 1143.The rate of heat transfer from a hot region to a cold region is affected most by the __________.
- 1144.Which of the conditions listed is one indication of an excessive amount of refrigerant in the system?
- 1145.When replacing a steam pressure reducing valve, what information is required for the selection?
- 1146.According to Coast Guard Regulations (46 CFR), a welded repair to be made to a ships service air receiver, other than an emergency repair at sea, must be __________.
- 1147.The meat box temperature control circuit, as used in the ship service refrigeration system, is an example of __________.
- 1148.Who is responsible for ensuring that someone is assigned to close the watertight doors in an emergency?
- 1149.If the pump in a hydraulic system produces a low rumbling noise while in operation, this is a probable indication of __________.
- 1150.A three-way solenoid operated dump valve installed on a flash-type evaporator unit, will divert impure distillate to the bilge __________.
- 1151.Which of the following statements is correct concerning heat transfer?
- 1152.On tank vessels equipped with power operated cargo tank valves, the type of power actuator most commonly used is __________.
- 1153.Excessive wear on the packing rings nearest the pump packing gland, while the rings nearest the impeller remain in good condition, is caused by __________.
- 1154.Which of the following elements is common to all indicating instruments?
- 1155.Leakage of hydraulic fluid from around the shaft of a hydraulic motor may be caused by __________.
- 1156.In a flash-type evaporator, an electrical salinity cell would be installed in the __________.
- 1157.If the viscosity of the liquid being transferred remains constant as the discharge pressure increases, the rotary pump __________.
- 1158.When metal is tempered, it becomes __________.
- 1159.If the suction pressure at the refrigeration compressor is below normal, the cause can be __________.
- 1160.Coast Guard Regulations (46 CFR) prohibit air compressors from being located in __________.
- 1161.'Offset' is an inherent characteristic of which of the following types of control modes?
- 1162.If dirt is allowed to contaminate the sump of a hydraulic deck crane, which of the following problems will occur?
- 1163.Where would a salinity cell be installed in a double-effect distilling plant?
- 1164.Which of the listed conditions will occur if the discharge pressure of a rotary pump is increased from the designed 50 psi to 300 psi, while maintaining the same RPM?
- 1165.Reheating a hardened component to a temperature lower than the hardening temperature and then cooling it is known as __________.
- 1166.If the suction pressure for an operating refrigeration compressor is below normal, the cause may be __________.
- 1167.One of the many problems occurring with centrifugal pump shaft packing is the excessive wear on the rings nearest the packing gland. If the rings nearest the impeller remain in good condition during the same operating period, the wear is most likely caused by __________.
- 1168.Which of the following definitions can be used to define the term 'offset' as a characteristic of controller action?
- 1169.When a new section of shell plating is being installed, the proper weld sequence must be followed to __________.
- 1170.A salinity indicator is used to determine the __________.
- 1171.In order to tighten the bolts of a crankpin bearing to the exact tension specified by the engine manufacturer, you should use a/an __________.
- 1172.Which of the conditions listed could cause excessively low refrigerant pressure at the compressor suction?
- 1173.Oil sprays on to a hot piece of machinery, catches fire and causes $35,000 damage to your vessel. By law this must be reported to the __________.
- 1174.Coast Guard Regulations (46 CFR) require safety and relief valves for air service to be provided with a substantial lifting device, capable of lifting the disk from its seat when the pressure in the vessel is __________.
- 1175.Which of the following definitions best describes sensitivity as a characteristic of controller action?
- 1176.Sounding tubes and access openings for fuel oil tanks on MODUs are permitted by Coast Guard Regulations (46 CFR) to be located in which of the listed spaces?
- 1177.If the relief valve on the discharge side of a hydraulic pump lifts, the cause could be __________.
- 1178.A welding electrode is marked E-6010, this designation means that __________.
- 1179.Before power to a lathe is turned on, it is a good shop practice to first hand feed the carriage to ensure __________.
- 1180.In an operating, water-cooled, multi-box refrigeration system, both low discharge and high suction pressures are being simultaneously experienced. The probable cause for this condition is a/an __________.
- 1181.Charring or glazing of the inner circumference of the packing rings in a centrifugal pump, is caused by __________.
- 1182.A mandatory characteristic of a pure amplifier is that __________.
- 1183.A grease drop point is __________.
- 1184.A drill that wobbles while the drill press is in operation may __________.
- 1185.Setting the relief valve opening pressure in a hydraulic system lower than the required operating pressure will result in __________.
- 1186.The high strength structural steel, such as Grade DH 32, when used as part of the main deck plating, is noted on the vessel's Certificate of Inspection. The information is important because __________.
- 1187.Large size pipe can be easily rotated with a __________.
- 1188.If a refrigeration compressor had developed a high suction pressure, the problem could be a result of __________.
- 1189.If you have to completely grind a new point on a high speed drill, which of the following could happen if it is cooled in cold water immediately after grinding?
- 1190.According to Coast Guard Regulations, if a pressure vessel, such as a ships service air tank, has defects which may impair its safety, the tank shall be __________.
- 1191.A pure transducer utilizes __________.
- 1192.Steam tables can be used to obtain the __________.
- 1193.The rate of heat transfer between the hot and cold fluids passing through a shell-and-tube type heat exchanger will __________.
- 1194.A tool used for measuring, or laying out angles is called a __________.
- 1195.A coolant is usually used when cutting metal in a power hacksaw to prevent the __________.
- 1196.If a refrigeration compressor had a higher than normal suction pressure, the problem could be a result of __________.
- 1197.A pneumatic pressure tank is installed in a sanitary system to __________.
- 1198.One of the many troubles occurring with centrifugal pump shaft packing is the excessive wear on the rings nearest the packing gland, while the rings nearest the impeller remain in good condition. This wear may be caused by __________.
- 1199.While calibrating a bourdon tube pressure gage, all readings are found to be 10 pounds higher throughout its entire range. An adjustment should be made by __________.
- 1200.Return lines to hydraulic systems reservoirs should________.