USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 9
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 801.In the event of a power failure to the salinity panel on a flash-type evaporator, the three-way solenoid valve will __________.
- 802.Positive displacement, helical gear pumps are well suited for pumping oil because __________.
- 803.Scale formation in a flash-type evaporator is usually found in the __________.
- 804.Coast Guard Regulations (46 CFR) require hydraulic steering gear systems to be equipped with a means of steadying the rudder in an emergency. This may be accomplished with __________.
- 805.After disassembly, the safest way to remove carbon deposits from air compressor inlet and discharge valves is to use __________.
- 806.In a water cooled stern tube, a slight leakage of water across the packing gland is provided to __________.
- 807.The component of a refrigerating system in which the refrigerant vaporizes and absorbs heat is known as the __________.
- 808.In which of the areas listed would you expect to find the highest salt concentration in a flash evaporator?
- 809.The flash chamber of a soloshell evaporator is typically an external chamber used for the combining of the distillate produced at two different absolute pressures. On a multistage flash-type evaporator, the flash chamber is __________.
- 810.Coast Guard regulations (46 CFR) require the upper ends of sounding tubes, terminating at the weather deck, to be closed by a __________.
- 811.The main bearings of a reciprocating air compressor are tapered roller bearings. When mounted, these bearings are given a 'cold' end clearance to __________.
- 812.Generally speaking, when using a twist drill to bore a hole in metal, the harder the metal, the greater should be the drill's __________.
- 813.To operate a centrifugal fire pump at reduced capacity, you should __________.
- 814.Steam supply for the operation of the low pressure evaporators may be obtained directly from the __________.
- 815.The brine level in the second-stage of a flash-type evaporator is determined in part by the feed rate, the rate of evaporation in both stages, and the __________.
- 816.Coast Guard Regulations (46 CFR) require that tank sounding pipes terminating below the freeboard deck of a cargo vessel must be fitted with a __________.
- 817.Any restriction in the instrument air piping of a pneumatic control system will __________.
- 818.If one drive belt on an air compressor is found to be worn you should __________.
- 819.The discharge rate or capacity of a centrifugal pump will vary directly as the __________.
- 820.If you are machining work held between lathe centers, and the lathe centers begin to squeal, you should first __________.
- 821.The term 'oil foaming' in refrigeration practice, is used to describe the __________.
- 822.Where auxiliary steam supply is not used in the process of maintaining vacuum in a distilling unit, the vacuum is usually attained by __________.
- 823.When operating with a negative suction head, which of the following types of pumps will require priming?
- 824.Which of the listed pressure-control valves is used in a hydraulic system to prevent the stray movements of a vertical load until required?
- 825.A saltwater leak shorts out your switchboard causing a fire which does $(USA)27,500 damage to the electrical equipment. This must be reported to the __________.
- 826.A Bourdon tube pressure gage is protected from the effects of the steam entering the pressure element by a/an __________.
- 827.If the drive belts on an air compressor were squealing, you should fix them by __________.
- 828.The refrigerant leaves the evaporator of a refrigeration system as a low pressure __________.
- 829.The purpose of a three-way, solenoid, dump valve on an evaporator is to __________.
- 830.Reduced capacity, accompanied by vibration and noise at the suction of a centrifugal pump is a result of __________.
- 831.The size of the loop seal orifice for a flash-type evaporator is important for maintaining the control of __________.
- 832.A measurement of .625 inches is equal to __________.
- 833.In order to accurately measure very low positive pressures, which of the instruments listed should be used?
- 834.A work piece has been mounted between centers and a test cut machined at each end to check alignment of the lathe centers. If the test cut on the tailstock end is deeper than the test cut on the headstock end, the tailstock must be moved __________.
- 835.A solenoid-operated distillate three-way valve is installed in the discharge line between the distilling plant and the potable water tanks. This valve will trip and dump the distillate discharge if the __________.
- 836.If a centrifugal bilge pump were continually operated with the discharge valve closed the __________.
- 837.Which of the listed pressure control valves would be used to establish the maximum operating pressure of a hydraulic system?
- 838.Coast Guard Regulations (46 CFR) define several acceptable means of closure for ballast and fuel oil tank vents. One of the acceptable means is by the use of a/an __________.
- 839.Before disconnecting a joint in a pipeline, you should __________.
- 840.The neutralization number of lube oil used in the machinery has exceeded its permissible range, therefore, it will be necessary to __________.
- 841.For proper support when turning a long thin piece of work between lathe centers, you should use a __________.
- 842.A centrifugal pump operating against a closed discharge valve has a/an __________.
- 843.While in operation, the function of the orifice in the flash evaporator loop seal is to __________.
- 844.A water line ruptures under pressure and floods the engine room causing $(USA)30,000 damage to the machinery. By law, this must be reported to the __________.
- 845.Joints in pipelines must be properly aligned before they are connected because __________.
- 846.The lathe steady rest is normally used for supporting one end of a __________.
- 847.In a typical refrigeration system, the temperature of the refrigerant gas is the highest __________.
- 848.Condensate formed within the tubes of the first-effect submerged tube nest of a double-effect, low pressure evaporator, is removed by a __________.
- 849.A centrifugal pump attempting to develop flow against a closed discharge valve has a/an __________.
- 850.The function of the loop seal, as typically provided on a flash type evaporator, is to __________.
- 851.A fuel oil settler is 35 feet 4 inches long, 25 feet 10 inches wide, and 19 feet deep. The noon sounding showed a level of 15 feet 2 inches. The oil meter reads 6517 at that time and 8911 at 1600. How many barrels of fuel oil remained in the settler a
- 852.A compound gage is used to measure __________.
- 853.Before making up a flanged joint, you should __________.
- 854.Coast Guard Regulations (46 CFR Part 56) require that screw joints shall not be used in piping systems where severe erosion, crevice corrosion, shock, or vibration is expected to occur, nor at temperatures over __________.
- 855.If you are taking a roughing cut on a steel work piece in a lathe and see blue chips coming off that work piece, you should __________.
- 856.Which of the listed components is considered to separate the high pressure side of a refrigeration cycle from the low pressure side of the cycle?
- 857.Fluctuations in the pressure and temperature of the steam supplied to the first-effect of a low pressure distilling plant will cause __________.
- 858.If a centrifugal pump operating with a positive suction head becomes air bound, your FIRST response should be to __________.
- 859.If 'wet' steam is supplied to the air ejectors of a low pressure evaporator, the passage of the mixture through the nozzles will __________.
- 860.When assembling a run of liquid service piping, which of the following factors should be considered?
- 861.When knurling a piece of work on a lathe, it is important to __________.
- 862.Which of the listed refrigeration system components keeps the refrigerant circulating through the system?
- 863.If a horizontal centrifugal pump becomes air bound, the pump should be vented at the __________.
- 864.Which of the valves listed is NOT considered to be a hydraulic system directional control valve?
- 865.A fuel oil settler is 35 feet 4 inches (10.7696 m) long, 25 feet 10 inches ( 7.8740 m) wide, and 19 feet (5.7912 m) deep. The noon sounding indicated a level of 15 feet 2 inches (4.6228 m). The fuel oil meter read 6517 (24669) at that time and 8911 (33732) at 1600. How many barrels / cubic meters of fuel oil remained in the settler at 1600?
- 866.A compound Bourdon tube gage is capable of measuring pressure and __________.
- 867.One function of the vapor feed heater in a double-effect submerged tube distilling unit is to __________.
- 868.Antifriction bearings should not be excessively lubricated because __________.
- 869.Excessive oil foaming in the crankcase of a refrigeration compressor at start up can cause __________.
- 870.For optimum non-condensable gas removal from a low pressure evaporator, the air ejector suction is usually taken directly from __________.
- 871.Which of the valves listed is NOT considered to be a hydraulic system directional control valve?
- 872.An air tank rusts out, explodes, and causes in excess of $(USA)24,000 damage to the engine room. By law, this accident must be reported to the __________.
- 873.A compound gage is typically installed on the __________.
- 874.From where does the air ejector take its suction on a Soloshell double effect distilling unit?
- 875.Work that cannot readily be mounted between lathe centers is usually held in a __________.
- 876.In a double-effect distilling unit, the brine in the second-effect is additionally heated by __________.
- 877.When securing a distillate pump on a low pressure fresh water evaporator, which of the listed steps should be carried out FIRST?
- 878.A vacuum is initially established in the first and second stages of a low pressure evaporator by the use of __________.
- 879.The disc of a relief valve has an area of 0.85 square inches when seated, lifts at a set point pressure of 250 psi. When the valve lifts, the area of the disc exposed to pressure increases by 20%. At what pressure does the valve reseat?
- 880.The gage most commonly used aboard ship to measure high pressures is the __________.
- 881.The delivery rate of an axial piston hydraulic pump is controlled by varying the position of the __________.
- 882.For boring holes in mild steel and general work, the correct included angle of a drill point is __________.
- 883.The vapor separators installed in some distilling plants consist of several rows of vertical hooked vanes which remove entrained moisture from the vapor by __________.
- 884.Steam passing through the control orifice installed in the live steam supply to a low pressure evaporator will develop significant superheat as a result of __________.
- 885.Coast Guard Regulations (46 CFR) specifically prohibit seats or disks in pressure vessel relief valves to be made of __________.
- 886.The type of gage most commonly used to measure pressure is the __________.
- 887.A depth of cut of 0.26 inch reduces the diameter on a work piece in a lathe by __________.
- 888.If condensation collects and drips off an evaporator coil, the temperature of the coil is __________.
- 889.In which of the listed types of evaporators is brine density control most important?
- 890.A dial indicator is used to measure __________.
- 891.Why is a self-sealing pump generally not satisfactory for service as a brine overboard pump?
- 892.Two separate work pieces are to have a taper cut with the same taper per inch, using the offset tailstock method. After the first piece is completed, the tailstock offset must be changed if there is a change in the __________.
- 893.Refrigerant is circulated through a refrigeration system by the __________.
- 894.For efficient and proper operation, the brine density in a submerged tube evaporator should be maintained at __________.
- 895.Regarding the low pressure evaporator steam control orifice in the live steam supply line, the steam at the outlet of the orifice if not properly conditioned will be developed as __________.
- 896.A pyrometer is generally used to measure __________.
- 897.The distillate pump for a 12000 GPD evaporator, should be rated at a minimum of __________.
- 898.A stopper is inserted into the spout of a closed container in which water has been heated to a temperature of 212°F. If additional thermal energy is imparted, what changes will occur to the pressure and temperature inside the container?
- 899.A tailstock 'dead center' has been given that name because it __________.
- 900.The temperature of the refrigerant in the evaporator coil depends mostly upon the __________.