USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 31
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 3001.Small irregularities on the seat and disk of a globe valve may be manually repaired with the valve in place by the process known as __________.
- 3002.Flanged joints in high pressure hydraulic system piping are commonly made leak proof by __________.
- 3003.Prussian blue is used to __________.
- 3004.The open-end wrench size for a standard 3/4 inch American National hex head bolt is __________.
- 3005.Which of the following statements is true concerning V-belt drives for reciprocating air compressors?
- 3006.Which of the listed statements is true concerning the start-up of a main propulsion boiler centrifugal feed pump?
- 3007.What would probably occur if excessive misalignment existed between a centrifugal pump and its power source?
- 3008.Piping is sized by its nominal __________.
- 3009.In a refrigeration system, the pressure in the control tubing of a thermostatic expansion valve depends upon the __________.
- 3010.A typical shipboard domestic multi-box refrigeration system operates with one compressor and condenser. What is the purpose of the sensing line connected to the thermal bulb at the evaporator coil outlet?
- 3011.If you have a duplex, single acting, reciprocating pump making 140 strokes/minute with a 3" diameter cylinder, and a 12" stroke with a 94% volumetric efficiency, what is the capacity of this pump?
- 3012.If a centrifugal pump sealing line becomes restricted while operating under a negative suction head (suction lift), which of the following may occur?
- 3013.The operation of a bellows type thermostatic steam trap depends upon the __________.
- 3014.The metal scribe of a combination square should only be used to __________.
- 3015.What percent of a roller bearing should normally be filled with grease?
- 3016.Which recovery procedure should be used to minimize the loss of oil from the system during the recovery of refrigerant from small appliances such as a water cooler?
- 3017.The size of flexible hose used in a hydraulic system is indicated by __________.
- 3018.What common practice is used to reduce the response time for a bearing thermometer using a protective well?
- 3019.Small leaks in flange gaskets should be stopped immediately after installation because __________.
- 3020.Which drill size would you use to machine and tap a 3/4 -10 National Coarse internal thread?
- 3021.An aligning punch is commonly used to __________.
- 3022.In a centrifugal pump, the purpose of the sealing line is to provide liquid from the discharge side of the pump directly to the __________.
- 3023.When welding or burning with an oxygen-acetylene torch, the acetylene hose working pressure must not exceed __________.
- 3024.A constant pressure range is maintained in the potable water system of many vessels by using __________.
- 3025.To ensure an accurate tank level pneumercator reading, you should __________.
- 3026.Which of the following statements regarding refrigeration systems is/are true?
- 3027.One important objective of a practical skill demonstration for mariner certification is to __________.
- 3028.If a hole were to form in the division plate between stages of a flash type evaporator __________.
- 3029.The efficiency of a flash type evaporator can be increased by __________.
- 3030.Which of the following modes of heat transfer does NOT require any physical contact between a warmer and a cooler substance?
- 3031.The result of mounting an impeller of a double suction centrifugal pump impeller with the vanes facing the wrong direction, would cause the pumps __________.
- 3032.Protective equipment to be used while carrying out oxy-acetylene welding should always include __________.
- 3033.According to 46 CFR Part 61, which of the following machinery remote control shutdowns is/are required to be tested during each regular inspection for certification?
- 3034.Which of the following methods is normally used to control the circulated air temperature of an air conditioning system using chilled water circulation?
- 3035.An unloader is installed on an air compressor to __________.
- 3036.When a refrigeration compressor is in the 'off' cycle, the thermal expansion valve __________.
- 3037.One cubic foot of salt water would equal approximately how many pounds?
- 3038.Distilled water from an evaporator is normally discharged into a potable water tank __________.
- 3039.An axial piston, variable stroke pump is used in a vessel's hydraulic steering gear. Under pressure, the oil leakoff from between the valve plate and cylinder barrel will __________.
- 3040.Which of the following statements regarding low pressure, reciprocating, air compressor valves is correct?
- 3041.Fluctuating pressures and temperatures in a low pressure fresh water evaporator will __________.
- 3042.According to Coast Guard Regulations (46 CFR), a power driven auxiliary steering gear for a vessel capable of a 20 knot service speed, must be capable of producing a specific range of rudder movement at which of the minimum speeds listed below?
- 3043.Which of the listed pressure control valves would be used to permit the completion of one action of a hydraulic system before a second action would be permitted?
- 3044.To thoroughly pump out the bilges using a horizontally mounted centrifugal pump, the __________.
- 3045.Which of the following statements concerning braze welding is/are correct?
- 3046.In accordance with Coast Guard Regulations (46 CFR Part 56), a nonmetallic flexible hose, used in a nonvital freshwater system, operating at 125 psi must be constructed __________.
- 3047.A refrigeration system is found to be too warm, and the compressor is not operating. A service check determines the compressor suction pressure to be above the normal cut-in point, with a normal head pressure, and high evaporator superheat. Which of the following could be the cause of the problem?
- 3048.Which of the listed values represents the temperature at which water will change to saturated vapor at a pressure of 14.7 psia?
- 3049.A lower thermostatic temperature setting will generally tend to cause an air conditioned space to have a __________.
- 3050.Which of the listed metals offers the best resistance to sea water corrosion?
- 3051.Which of the listed pressure vessels is normally exempt from hydrostatic testing at the regular Coast Guard inspection for certification occurring four years after the initial inspection?
- 3052.The transfer of heat within a solid, caused by the application of thermal energy, is called __________.
- 3053.With respect to machine shop "taps and dies", a plug tap is correctly used for __________.
- 3054.When adding packing to a pump shaft seal, you must be careful to prevent __________.
- 3055.In order to minimize distortion in a weldment due to shrinkage, you should __________.
- 3056.In a small refrigeration appliance using HFC-134a you would expect to see the greatest temperature drop across the __________.
- 3057.The primary function of a back pressure regulator installed in a multi-box refrigeration system is to __________.
- 3058.Which of the following problems occurring in a hydraulic system can be caused by using an oil having a viscosity lower than specified?
- 3059.The efficiency and output capacity of a low pressure distilling plant will be greatly reduced if __________.
- 3060.A simplex pump making 60 pumping strokes per minute has a 10 inch stroke and a 6 inch diameter water cylinder, which is 75% full for each stroke. How many gallons of water are discharged per hour?
- 3061.Operating a water service centrifugal pump with an excessive amount of wearing ring clearance would result in _______.
- 3062.Which of the listed materials have been used to manufacture piping available in standard weight, extra strong, and double extra strong wall thickness?
- 3063.Which of the following statements represents an advantage of a triple-effect submerged tube evaporator compared to a single-effect submerged tube evaporator?
- 3064.If a flash-type evaporator is operating in extremely cold seawater temperatures, the engineer may expect that __________.
- 3065.If the evaporator feed temperature from a flash type evaporator falls below 160°F __________.
- 3066.Which refrigerant listed is considered to have the highest ozone depletion potential?
- 3067.In the normal operation of a refrigeration system, when the refrigeration compressor cycles "off", the thermal expansion valve will _________.
- 3068.Which of the following statements represents an operating characteristic of neoprene or rubber stern tube bearings?
- 3069.Where would you find the greatest amount of refrigerant superheat in an operating refrigeration system?
- 3070.The capacity of a fuel oil transfer pump is 100 gpm. If a fuel oil setting tank measures 6 feet by 6 feet by 12 feet high, how long must the pump run to fill the tank to 11 feet, if the tank presently holds 2 feet of fuel?
- 3071.What would be the final mean draft in sea water of a 10 foot by 10 foot by 50 foot long barge weighing 10 long tons, if it was evenly loaded with an additional 50 long tons of cargo?
- 3072.Which of the following factors should be considered when calculating the air conditioning requirements for a vessels accomodation spaces?
- 3073.What is the main reason that live auxiliary steam is normally attemporated before entering the feed heater of a flash evaporator?
- 3074.On all vessels equipped with ammonia refrigeration units of over 20 cubic foot capacity, __________.
- 3075.The proper operation of a P-tank as found on oil industry supply vessels, depends primarily upon __________.
- 3076.Which of the following is true concerning the proper use of a machine shop hand hack saw?
- 3077.Which of the listed statements is correct concerning refrigeration systems?
- 3078.Which of the listed statements is correct concerning refrigeration capacity is true?
- 3079.Which of the precautions listed should to be observed when working with oxy-acetylene welding equipment?
- 3080.Protective equipment while carrying out oxyacetylene welding should include the use of __________.