USCG Engineering General Subjects – Question Bank Book 11 (BK11)
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1.Tubing is sized by __________.
- 2.Short cycling of a refrigeration compressor refers to __________.
- 3.The emergency bilge suction valve is typically used __________.
- 4.The by-products of oxidation, as a result of water contamination of hydraulic oil, are generally __________.
- 5.A record of the types and strengths of steels used on a MODU must be included in the __________.
- 6.Which of the fittings listed should be used for the installation of new water pump piping to permit removal of the pump for servicing?
- 7.A continuous watertight bulkhead on a MODU may also be a/an __________.
- 8.Which of the following describes the purpose of a striker or doubler plate?
- 9.A high reading at a salinity cell located in the loop seal between two stages of a flash type evaporator would indicate __________.
- 10.Regarding MODU construction, bulkheads in the quarters are generally __________.
- 11.In machine shop practice, a center gage is used for checking the angle of __________.
- 12.A portion of the cargo of an LNG carrier boils off during each voyage. How is the cargo boil off normally handled?
- 13.Air leaking into a flash type distilling plant could occur through __________.
- 14.The construction portfolio may be included as part of the MODU __________.
- 15.Which of the following statements represents the proper relative direction of flow through a globe valve?
- 16.Vertical partitions providing strength and compartmentation on a MODU are called __________.
- 17.Which of the listed types steam traps operates on the principle that hot water flashes to steam when its vapor pressure is rapidly reduced?
- 18.The heat gained per pound of refrigerant in the evaporator is known as the __________.
- 19.A squealing sound occurring from within an operating reciprocating air compressor is an indication of __________.
- 20.A mooring winch should be equipped with mechanical brakes capable of holding __________.
- 21.The requirements for special welding procedures to be used on a MODU must be contained in the __________.
- 22.Bulkheads forming part of the tanks on a MODU are stiffened to withstand __________.
- 23.The operation of a thermostatic steam trap depends upon the __________.
- 24.The process of removing moisture from air is known as __________.
- 25.Which of the following describes the function of the air receiver in the compressed air system on a MODU?
- 26.A centrifugal bilge pump requires priming __________.
- 27.A suitable location for the installation of an impulse type steam trap would be in the __________.
- 28.Which of the listed conditions can lead to cavitations in a centrifugal pump?
- 29.Coast Guard Regulations (46 CFR) require refrigerated spaces that can be locked from the outside and cannot be opened from the inside to have an audible alarm to sound in __________.
- 30.The hydraulic oil most likely to thin out when hot and thick when cold would have a viscosity index of __________.
- 31.The decks of a MODU are supported by transverse members called __________.
- 32.Why is electrical power preferred over mechanical power for driving heavy machinery on drilling rigs?
- 33.On a MODU, the keel is the primary strength member of the lower hull form and is laid in which direction?
- 34.How is water traveling along the shaft of a centrifugal pump prevented from entering the shaft bearing?
- 35.Which of the following descriptions best identifies the operating principal of a flash-type evaporator?
- 36.If air at 95°F dry bulb temperature and 50% relative humidity is conditioned to 75°F dry bulb temperature and 50% relative humidity, it is an example of __________.
- 37.The volatility of any oil may be indicated by __________.
- 38.A simplified construction plan may be included in the MODU construction portfolio provided it adequately defines the __________.
- 39.What is a function of the wearing rings used in most centrifugal pumps?
- 40.Between the side frames of a MODU, support for the deck beams is provided by __________.
- 41.A pneumercator tank gage utilizes __________.
- 42.A tank of a MODU, with a volume of 2,000 cubic feet, is pressed up with sea water weighing 64 pounds per cubic foot. What is the weight, in kips, of the liquid?
- 43.For MODU's operating under the U.S. flag, the construction portfolio must contain __________.
- 44.When liquid reaches the compressor of a refrigeration system through the suction line, the condition is called __________.
- 45.The term 'pour point' is defined as the lowest temperature at which lubricating oils will flow __________.
- 46.In the MODU construction portfolio, materials which do not conform to ASTM or ABS specifications must also include the __________.
- 47.Deck beams on a MODU are generally spaced at equal intervals and run __________.
- 48.An acetylene pressure regulator should never be adjusted to maintain pressures exceeding 15 psig (103.4 kPa) because __________.
- 49.The pressure range between the system cut-in and cut-out pressures in a refrigeration unit is known as __________.
- 50.Prior to the burning or welding of a fuel tank on a MODU, regulations require that an inspection be made. An entry in the unofficial logbook is required if this inspection is made by __________.
- 51.A welding procedure used for joining dissimilar metals used in the construction of a MODU would be recorded in the __________.
- 52.The record of tests and inspection of fire fighting equipment on board a MODU must include __________.
- 53.The deck plating on a MODU is supported primarily by deck longitudinals and deck __________.
- 54.How long must the records of tests and inspections of fire fighting equipment for a MODU be retained on board?
- 55.A reciprocating air compressor is running roughly and vibrating excessively, indicating that the __________.
- 56.Increasing the moisture content of conditioned air is known as __________.
- 57.The master or person in charge of a MODU is required to log __________.
- 58.In a radial piston pump, reversal and control of fluid flow are accomplished by moving the __________.
- 59.What must be entered in the unofficial logbook by the master or person in charge of a mobile offshore drilling unit after conducting a fire drill?
- 60.After conducting a boat drill, the master or person in charge of MODU shall log __________.
- 61.The deck loads on a MODU are distributed through the deck beams to the __________.
- 62.One cause of leaky valves in a low pressure air compressor may be attributed to __________.
- 63.To maintain design discharge pressure from a centrifugal pump, the design clearance must be maintained between the __________.
- 64.Which of the following statements represents the difference between a four-jaw independent chuck and a three-jaw universal chuck?
- 65.Enlarging one tube end so the end of another tube of the same size will fit inside is termed __________.
- 66.Stern tube and strut bearings lined with hardwood or rubber composition materials are lubricated with __________.
- 67.The purpose of annealing any metal is to make the metal __________.
- 68.When the longitudinal strength members of a MODU are continuous and closely spaced, the vessel is __________.
- 69.Lifeboat winches on a MODU are required to be inspected and an entry made in the logbook. What should this entry include?
- 70.A fluctuating and unsteady vacuum in an evaporator may be caused by __________.
- 71.If a radial piston hydraulic pump fails to deliver rated fluid volume, the cause can be __________.
- 72.Pipe threads are cut with a taper to __________.
- 73.When the tilting box of a variable stroke axial-piston pump is perpendicular to the pump shaft, which of the following conditions will exist?
- 74.Which of the refrigerants listed is considered ideal for most marine applications?
- 75.Closed impellers differ from open impellers in that closed impellers __________.
- 76.A MODU having continuous closely spaced transverse strength members is __________.
- 77.With respect to centrifugal pump design, which of the following descriptions best represents a pump utilizing two impellers?
- 78.Which of the listed pipe sizes is not commonly used?
- 79.When using a sling psychrometer to determine relative humidity, the indicated difference between the dry bulb and the wet bulb reading is the __________.
- 80.The static positive suction head of a pump is the __________.
- 81.A grease lubricated ball bearing or roller bearing will run cooler if the grease __________.
- 82.The ash content of a fuel oil is significant to the operating engineer because it __________.
- 83.What is the diameter of a cylinder whose cross-sectional area is 706.86 square inches?
- 84.On a MODU, the deck stringer is the outboard most deck __________.
- 85.Which pipe listed has the largest outside diameter?
- 86.The sum of the sensible heat and the latent heat of any substance is known as __________.
- 87.Expansion of the tube bundle in a shell-and-tube type cooler may be provided for by the __________.
- 88.The pressure produced within the oil wedge of a rotating journal is __________.
- 89.Which combination of the main shaft segments listed below, that are located furthest from the main engine, are connected by the inboard stern tube shaft coupling?
- 90.Compared to internal structural plating, the exterior hull plating on a MODU is usually __________.
- 91.The gasket and the broken studs have been replaced on a tank manhole cover. Which of the following methods is satisfactory for testing the repair?
- 92.Piping cross-sections over 12 inches in diameter are sized by the __________.
- 93.The static suction lift of a pump is the difference in elevation between the __________.
- 94.The heat identified by only a change in temperature is known as __________.
- 95.The usual number of single-acting pistons used in a variable stroke axial-piston pump is __________.
- 96.Piping cross-sections ranging from 1/8 inch to 12 inches in diameter, are sized by __________.
- 97.An axial piston pump differs from a radial piston pump as the pistons of an axial piston pump are positioned __________.
- 98.In reference to air conditioning, when air attains the maximum amount of moisture it can hold at a specific temperature, it is said to be __________.
- 99.Positive displacement, helical gear pumps are well suited for pumping oil because __________.
- 100.The conical steel or composition cone installed on a propeller, known as a fairwater cone, provides which of the following benefits?