USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 15
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1401.Coast Guard regulations concerning marine sanitation devices may be found in __________.
- 1402.In MODU construction, beam brackets are triangular plates joining the deck beam to a __________.
- 1403.The cylinders and intercoolers of most low pressure air compressors are cooled by __________.
- 1404.A tap marked '1/4-20' will cut a thread __________.
- 1405.Which of the following problems will occur if a disk-type centrifugal lube oil purifier contains insufficient sealing water prior to admitting oil flow to the bowl?
- 1406.Feed water supplied to a flash type distilling plant will flash to vapor in the first-stage due to __________.
- 1407.Stanchions prevent the entire deck load on a MODU from being carried by the __________.
- 1408.The Phillips screwdriver has a blunt end and flukes with an angle of __________.
- 1409.An important consideration in selecting a lubricating oil for use in a refrigeration compressor is for the oil to __________.
- 1410.If the intercooler relief valve lifts while an air compressor is operating under load, you should check for __________.
- 1411.Which of the following statements represents the main difference between a stuffing box gland and a mechanical seal for sealing the shaft of a centrifugal pump?
- 1412.In a shell-and-tube type hydraulic fluid cooler, the amount of heat transferred from the hydraulic fluid to the cooling water depends upon __________.
- 1413.Support of MODU side plating is provided primarily by transverse __________.
- 1414.With regards to the American National Screw Thread nomenclature, 'pitch' is the __________.
- 1415.The presence of scale and dirt on the saltwater side of a lube oil cooler is usually indicated by __________.
- 1416.One refrigeration ton is equal to __________.
- 1417.A leaking suction valve in the second stage of a two stage, high pressure, air compressor can cause excessively high __________.
- 1418.The tool used to remove a ball bearing from the shaft of a motor is called a __________.
- 1419.Fabric type packing, such as flax or hemp, is best suited for __________.
- 1420.Which of the listed problems is occurring if a coil type high pressure evaporator constantly requires an increase in the coil steam pressure in order to maintain capacity?
- 1421.Lighter longitudinal stiffening frames on the MODU side plating are called __________.
- 1422.The follow-up gear on an electro-hydraulic steering gear __________.
- 1423.Which of the following statements is true concerning a radiator type heat exchanger?
- 1424.How much heat can a 5 ton refrigeration unit remove from a refrigerated space?
- 1425.Leaking valves in an air compressor can be a result of __________.
- 1426.When renewing spiral packing in a centrifugal pump stuffing box, after the packing is firmly seated, the packing gland nuts should be __________.
- 1427.Aftercoolers are used with air compressors to __________.
- 1428.The heavier outboard strake of deck plating on a MODU is called the deck __________.
- 1429.In which of the following types of evaporators is the control of brine density least important?
- 1430.Heat exchanger tubes can be protected against erosion and abrasion by the use of __________.
- 1431.What is the equivalent tonnage of a refrigeration system rated at 48,000 BTU per hour?
- 1432.Leaking valves in a low pressure, reciprocating, air compressor can result from __________.
- 1433.Rudder motion is prevented from exceeding the movement of the steering wheel by the __________.
- 1434.An air compressor is equipped with an intercooler and an after cooler to __________.
- 1435.Return lines in a non-pressurized hydraulic system reservoir should enter the tank well below the fluid surface level to __________.
- 1436.Evaporator priming can be caused by high water level, fluctuating steam pressure, or __________.
- 1437.Where is thicker plating usually found in the construction of integral tanks on a MODU?
- 1438.When renewing the shaft packing on a centrifugal pump equipped with an external liquid sealing supply, you should __________.
- 1439.If an air conditioning system were rated at 24,000 BTU, the equivalent tonnage of the unit would be __________.
- 1440.If a ship service air compressor operating in intermittent service were failing to unload, the __________.
- 1441.On an electro-hydraulic steering gear, which of the listed devices will keep the rudder from over traveling the bridge signal?
- 1442.A multistage flash evaporator will be unable to produce consistently pure distillate if the __________.
- 1443.The Reed and Prince screwdriver has a sharp pointed end with flukes that have an angle of __________.
- 1444.When securing a centrifugal type distillate pump, which of the listed steps should be carried out first?
- 1445.On tankers with manually operated tank valves, the type of valve most commonly used is the __________.
- 1446.If a refrigeration box develops a heat load of 60,000 BTU/hour, what size refrigeration unit would be required?
- 1447.In heat exchangers, seawater pressure should be maintained lower than freshwater pressure to __________.
- 1448.Which of the following is the probable cause for a motor driven, low pressure, reciprocating air compressor to repeatedly trip the circuit breaker upon starting?
- 1449.Most hydraulic steering gears are fitted with relief valves which __________.
- 1450.Steam supply piping to deck machinery is insulated in order to __________.
- 1451.A piece of tapered round stock 36 inches long, 4 inches in diameter at the large end and 2 1/2 inches in diameter at the small end. What tailstock set over was used to machine the taper?
- 1452.What is the maximum steam pressure allowed by Coast Guard Regulations (46 CFR) to be provided in the steam heating system of the living spaces?
- 1453.When a heat exchanger is used as a cooler, excessive cooling water flow should be avoided to prevent __________.
- 1454.After the installation of new impeller wearing rings by pressing them onto the pump impeller hub, it is advisable to __________.
- 1455.If a refrigeration system extracted 48,000 BTU per hour, the equivalent tonnage of the unit would be __________.
- 1456.If a ship service air compressor failed to unload the __________.
- 1457.In an electro-hydraulic steering system, rudder shock is limited by __________.
- 1458.Which of the following statements is true regarding a positive displacement rotary pump?
- 1459.Rapid fluctuation of the last effect shell vacuum in a submerged tube evaporator can cause __________.
- 1460.In a heat exchanger, excessive fluid velocity should be avoided to prevent __________.
- 1461.Compensated flow control, or constant flow valves are used in hydraulic systems to __________.
- 1462.An air conditioning system, required to remove from 33,000 to 35,000 BTU per hour, should have a minimum capacity of __________.
- 1463.Carryover in a flash type distilling plant can be a result of __________.
- 1464.If a ship service air compressor failed to unload, the __________.
- 1465.If a centrifugal pump develops insufficient discharge pressure as a result of worn wearing rings, which of the following corrective actions is required?
- 1466.Accidental flooding of the engine room bilges through the bilge system is prevented by __________.
- 1467.When the compressed air reservoir is placed in line with an air compressor and is used as an after cooler, the reservoir must be __________.
- 1468.In an electro-hydraulic steering system, damage due to rudder shock is prevented by __________.
- 1469.A device incorporating a variable orifice placed in series with a check valve in a hydraulic system, is used to __________.
- 1470.The receiver used in a refrigeration system __________.
- 1471.Zinc anodes are installed in a marine sea water heat exchanger cooling system to __________.
- 1472.Major repairs or alterations affecting the safety of small passenger vessels of less than 100 gross tons shall __________.
- 1473.If there is a sudden drop in the capacity of a reciprocating air compressor, you should check for __________.
- 1474.When a reciprocating pump is operating at maximum speed, the cushioning valves should be __________.
- 1475.Rudder position is shown on the bridge by the __________.
- 1476.The purpose of a restrictor valve, as it is used in a hydraulic hatch cover system, is to __________.
- 1477.During the inspection for certification of small passenger vessel of less than 100 gross tons, a hydrostatic test of 1-1/4 times the maximum allowable working pressure shall be made to __________.
- 1478.If the capacity of a reciprocating air compressor gradually drops off, the cause could be __________.
- 1479.The static suction head of a horizontal centrifugal pump, is the difference in elevation between the __________.
- 1480.A drilled hole is accurately finished to size with a __________.
- 1481.In a refrigeration plant, one purpose of the receiver is to __________.
- 1482.Emergency lighting on small passenger vessels of less than 100 gross tons for lounge areas below the main deck shall be __________.
- 1483.When air compressors are arranged for automatic operation, the cylinders can be unloaded during starting by __________.
- 1484.If a higher than normal water level is observed through the inspection port of a flash evaporator, you should suspect __________.
- 1485.Reciprocating air compressor bearing failure may result from __________.
- 1486.In a fixed displacement axial piston hydraulic motor, the speed is varied by __________.
- 1487.When checking zinc plates, or pencils in the refrigerating system condenser, you should __________.
- 1488.For drilling or machining cast iron, which of the cutting lubricants is it necessary to use?
- 1489.One of the main differences between a propeller pump and a centrifugal pump is the absence of a __________.
- 1490.In a flash evaporator, scale as a result of higher than normal temperatures is most likely to occur in the __________.
- 1491.Which of the listed types of seals is used effectively for pumps handling toxic or highly flammable liquids that cannot be permitted to escape into the atmosphere?
- 1492.No two drills from differing drill sets are of the exact same size, with the exception of the drills measured as 0.25 inch. These two drills are the 1/4 inch and the __________.
- 1493.In MODU construction, a large number of watertight bulkheads results in __________.
- 1494.Which of the following statements describes the advantage of the mechanical shaft sealing system over the stuffing box and packing method of shaft sealing for propulsion shafting?
- 1495.Zinc rods are installed in the refrigeration system __________.
- 1496.A single-acting simplex pump makes 100 single strokes per minute. The diameter of the water cylinder is 6 inches and the stroke is 10 inches. If the efficiency of the pump is 90%, what is the capacity of the pump?
- 1497.Deck rails on passenger decks of vessels engaged in a ferry or excursion type operation shall be at least __________.
- 1498.Each vessel designed to carry more than 49 passengers must have __________.
- 1499.When shifting suction from one fresh water tank to another, if the fresh water pump loses suction you should___________.
- 1500.High salinity distillate being discharged from a flash-type distilling plant may be the result of __________.