USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 10
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 901.Which of the following types of hydraulic pumps would be used in a steering system?
- 902.The amount of the cushioning effect developed within a hydraulic cylinder is determined by the __________.
- 903.According to U.S. Coast Guard Regulations (46 CFR Part 32), when reach rods to tank valves pass through the deck, the stuffing box at this joint must be __________.
- 904.A 12" X 8" X 8" simplex double-acting pump makes 100 strokes per minute. If the slip is 6%, the discharge rate is __________.
- 905.An unsteady vacuum in a submerged tube evaporator may be caused by __________.
- 906.An increase in the heat load to a refrigeration system will cause __________.
- 907.Generally, centrifugal pumps operating without a positive suction head must be primed before they will move liquid on their own. The priming is usually accomplished with a __________.
- 908.A hydraulic system directional control valve fitted with 'detent' will __________.
- 909.Which of the following is true concerning the issuance and use of Coast Guard form 948 'Permit to Proceed to Another Port for Repairs'?
- 910.According to Coast Guard Regulations, flexible hoses used as supply and return lines to hydraulic system components, must have __________.
- 911.Which of the listed values represents the temperature of saturated vapor for water at a pressure of 14.7 psia?
- 912.The discharge head of a centrifugal pump will vary directly with the __________.
- 913.The boiling point of water in an open container at sea level is 212°F. If the pressure on the open container is decreased, the boiling point will __________.
- 914.A vacuum differential is maintained in the distillate circuit between any two stages of a multiple stage distilling plant by the use of a/an __________.
- 915.A fixed orifice plate is generally installed in the live steam supply to a flash evaporator. One of the functions of this orifice is to control the quantity of the supplied steam. A second function is to __________.
- 916.The hydraulic system of a deck winch has been drained, flushed, and refilled with hydraulic fluid. An erratic knocking noise from the hydraulic motor when the winch is started would indicate __________.
- 917.Which of the following terms would best describe the temperature at which a liquid boils at a given pressure?
- 918.When drilling a hole in a piece of work chucked in a lathe, you should mount the drill chuck in the __________.
- 919.A refrigerant with oil in solution has a __________.
- 920.Where a two-stage air ejector set is used in a two-stage flash evaporator, the first-stage air ejector takes suction from the second stage of the evaporator, and the second stage air ejector __________.
- 921.A centrifugal ballast pump has a capacity of 200 gpm. If suction is taken on a ballast tank containing 200 long tons of seawater, how much water will be remain in the tank after discharging for one hour?
- 922.A vapor under pressure stays in contact with, and at the same temperature as the liquid from which it was generated. The vapor and liquid in this situation are, therefore, said to be in a/an __________.
- 923.In a flash type distilling plant, a screen is fitted over the suction connection to the brine overboard pump in order to prevent __________.
- 924.In order to convert taper per inch to taper per foot, you should __________.
- 925.Packing extremely soft grease into a roller bearing will cause __________.
- 926.Centrifugal pumps, used to handle hot liquids, must have a minimum flow through them under all operating conditions. This flow serves to __________.
- 927.Hydraulic system reservoirs are often fitted with a combined filler/breather cap. If the breather element becomes fouled, the __________.
- 928.Coast Guard Regulations (46 CFR) concerning shutoff valves located inside fuel oil tanks, state that the valves __________.
- 929.A pneumercator is useful in measuring __________.
- 930.Machinery operating features are designed to help conserve energy. Which of the following results will not contribute to energy conservation?
- 931.On which of the following heated surfaces of a flash type evaporator would you be more likely to find soft scale formation?
- 932.The total static head of a system resisting the operation of a centrifugal pump is the difference in elevation between the __________.
- 933.The Certificate of Inspection for your vessel was issued in January. In March of the same year you need to replace a cooling water pump for the refrigeration system. What action would be appropriate?
- 934.If 1 Horsepower equals 42.45 BTU's per minute, then the energy required to lift a 1 pound (.454 kg) weight, 778 feet (.24 km), against the force of gravity, would be the same as the number of BTU's required to raise the temperature of __________.
- 935.Which of the following statements concerning the operation of a single-acting hydraulic ram is correct?
- 936.Coast Guard Regulations (46 CFR) require a single tail shaft with water lubricated tail shaft bearings, stress-relieved keyway, and fabricated from materials resistant to corrosion by sea water, to be drawn and examined once in every __________.
- 937.Excessive oil foaming in the crankcase of a refrigeration compressor is most likely to occur when the compressor __________.
- 938.Which of the following statements is correct with regards to the operation of a centrifugal cargo pump?
- 939.Some fluid filters used in hydraulic systems are designed to cope with increasing pressure differentials by __________.
- 940.A ballast pump, with a capacity of 200 gpm, takes suction on a tank containing 300 long tons of sea water ballast. How much ballast will remain in the tank after pumping for one hour?
- 941.Your vessel is departing at 1800 hours on a voyage of more than 48 hours duration. Coast Guard Regulations (46 CFR) require that the steering gear be examined and tested no earlier than __________.
- 942.The equation 'energy in = energy out' is a simple way of stating the principle of the __________.
- 943.With oil bath lubrication of ball bearings in a cargo pump, the oil level should __________.
- 944.The vessel has its propulsion machinery located amidships, using a water lubricated stern tube bearing, to carry a tail shaft of a 15 inch (38.1 cm) diameter. During the inspection the wear between the stern tube and the bearing surface was measured as 1/4 inch (.635 cm). Which of the following actions should be carried out as a result of this measurement?
- 945.In a compression refrigeration cycle, the temperature of the liquid refrigerant experiences its greatest decrease in the __________.
- 946.Which of the instruments listed is used to measure the gauge of a piece of sheet metal?
- 947.A recirculating, or bleed off line is installed on a centrifugal pump in order to __________.
- 948.An improperly maintained filter used in a hydraulic system can __________.
- 949.Which of the following would require the Officer in Charge, Marine Inspection be notified?
- 950.A pneumercator is used to indicate fuel oil __________.
- 951.Which of the following statements concerning energy is correct?
- 952.By which of the following means is force efficiently provided to vary the pitch of the blades on a modern controllable pitch propeller?
- 953.Which of the listed statements is correct concerning refrigeration systems?
- 954.When the vessel's steering wheel on the navigation bridge is turned, the difference existing between the position of the wheel and that of the rudder is known as __________.
- 955.A ballast pump with a capacity of 200 gpm (757 lpm) is used to fill a ballast tank with seawater. If the pump discharges seawater into the tank for one hour, how many tons of saltwater ballast have been taken onboard?
- 956.Double seated, pneumatically controlled, regulating valves exhibit good balancing characteristics essential for low-sensitivity applications because __________.
- 957.The quantity of heat required to raise the temperature of a unit mass of a substance 1° is known as __________.
- 958.After cutting a piece of tubing to be flared, you should __________.
- 959.To measure the circumference of a piece of pipe, you should use a __________.
- 960.When a centrifugal pump is operating with a positive suction head, the inner end of the stuffing box is __________.
- 961.Which of the following control actions, when combined with proportional-position action, will eliminate manual repositioning of the set point for each load change to produce an automatic reset action?
- 962.A reservoir, as used in hydraulic systems aboard ship, is used to store hydraulic oil. Another function is to __________.
- 963.According to U.S. Coast Guard Regulations (46 CFR Part 92), how many means of escape must be provided in spaces where the crew may be quartered or employed?
- 964.Which of the following terms is used to indicate that the addition of heat will result in a temperature change?
- 965.One turn of the micrometer barrel will linearly move the spindle __________.
- 966.What is the maximum tail shaft to stern tube bearing clearance (at the after end of the stern tube) for a vessel in ocean service, with an aft machinery space, a 14" diameter tail shaft, and a water lubricated stern tube bearing constructed of material other than rubber?
- 967.Frost appearing on one set of evaporator coils of a multi-box, direct expansion type refrigeration system __________.
- 968.To set the dividers to the proper radius, you should use a __________.
- 969.Theoretically, a double suction impeller is in hydraulic axial balance. In actuality this balance is rarely achieved due to __________.
- 970.Which of the following statements expresses the function of proportional-plus-reset action?
- 971.One function provided by a hydraulic accumulator is to __________.
- 972.In accordance with Coast Guard Regulations (46 CFR), it is the duty of the Chief Engineer to acquire and seal a sample of fuel oil received whenever fuel oil bunkers are taken. This sample must be preserved until __________.
- 973.If a micrometer were opened to a distance of 0.0001 inch, you would say the reading is __________.
- 974.The best method of determining the number of threads per inch of a bolt or screw would be through the use of a __________.
- 975.Shim stock thickness is measured by a/an __________.
- 976.A controller with floating action has a controlled variable where the range of values produces no motion of the final control element. This range of values is called the __________.
- 977.To check the thickness of a piece of thin shim stock before using it to make a bearing shim, you should use a __________.
- 978.When the tail shaft is drawn from a vessel in dry-dock, which of the following inspections is required to be carried out?
- 979.If the evaporator coil of a single box, air cooled refrigerator accumulates frost, the compressor will most likely __________.
- 980.The best tool to use to measure the number of threads per inch on a bolt is a __________.
- 981.Compared to globe and angle valves, gate valves __________.
- 982.One disadvantage of proportional-position action is that __________.
- 983.Which of the following conditions require the Coast Guard Officer in Charge of Marine Inspection be notified?
- 984.In the design of hydraulic piping and equipment consideration is given to minimize turbulence in the hydraulic fluid, as this will cause __________.
- 985.The quantity of heating steam supplied to the feed water heater of a two-stage flash type distilling plant is held relatively constant by a/an __________.
- 986.To measure the diameter of a piece of round stock, you should use a __________.
- 987.When using the circular magnetic particle method to nondestructively test a weldment, the best results are obtained when the __________.
- 988.If a refrigeration compressor is running continuously without lowering the temperature in the refrigerated space, the trouble may be __________.
- 989.The temper is likely to be drawn out from a chisel edge when you __________.
- 990.Which of the valves listed should be used either in the fully opened or the fully closed position?
- 991.A two-position single-point action controller has been adjusted to minimize cycling and would only be suitable for __________.
- 992.If a lifeboat winch allows a lifeboat to descend to the water at an excessive speed, you should __________.
- 993.Which of the following modes of heat transfer does NOT require any physical contact between a warmer and a cooler substance?
- 994.To get an accurate inside measurement of the diameter of a 1/2 inch hole, you should use a/an __________.
- 995.During tests to discover why a refrigeration compressor is running excessively, it is determined that the refrigerated space temperature is nearly normal, the suction pressure is slightly above normal, and the head pressure is low. In this situation, you should check for__________.
- 996.A chisel with a mushroom head should not be used because __________.
- 997.A gate valve installed in a pipeline should be __________.
- 998.When a controller is provided with reset rate adjustment, a change in this adjustment results in a change of the __________.
- 999.Energy losses occurring in a hydraulic system are ultimately absorbed by the __________.
- 1000.Air compressor cylinder unloaders enable the compressor to __________.