USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 11
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1001.Which of the conditions listed will cause a refrigeration compressor to run constantly without simultaneously decreasing the temperature in the refrigerated space?
- 1002.What precautions should be followed when using a chisel having a mushroomed head?
- 1003.A gate valve installed in a piping system should be used __________.
- 1004.Which of the listed methods of heat transfer takes place when two substances of different temperatures are in physical contact with each other?
- 1005.The unloading system on an air compressor will __________.
- 1006.A warmer than normal compressor suction line might be caused by __________.
- 1007.Solder used for joining metal surfaces should have a __________.
- 1008.The proper use of a flat chisel is for cutting __________.
- 1009.The amount of change of a controlled variable that is necessary to cause a specific change in the position of the final control element depends upon the __________.
- 1010.Which problems can occur if the brake band lining of a wildcat brake becomes excessively worn?
- 1011.Which of the following conditions must exist for heat to flow from one object to another?
- 1012.The function of an unloader on a two-cylinder, two-stage medium pressure, air compressor is to __________.
- 1013.How can the chance of contaminating hydraulic fluid be decreased when working on hydraulic systems?
- 1014.In the refrigeration system, a shortage of refrigerant is indicated by __________.
- 1015.The response line installed in a pneumatic proportional action controller functions to __________.
- 1016.A non-rising stem gate valve should __________.
- 1017.An electric power failure occurring in a electro-hydraulic steering gear would cause the rudder to __________.
- 1018.In a reciprocating pump, the position of the pilot valve is controlled by the position of the __________.
- 1019.Condensate must be drained from the intercooler and aftercoolers of an air compressor because __________.
- 1020.If a refrigeration system were short of refrigerant, the condition would result in __________.
- 1021.Tinning a soldering iron will __________.
- 1022.When a controller with proportional position action is used to control a process, a load change will cause the controlled variable to stabilize at some value other than the set point value. The new point at which the controlled variable stabilizes is called __________.
- 1023.The handle of a butterfly valve must be __________.
- 1024.The purpose in constructing a pipe tunnel aboard a vessel is to __________.
- 1025.When air becomes trapped in the hydraulic fluid of a steering system, the __________.
- 1026.Before starting a reciprocating, steam-driven pump that has been idle for a period of time, you should __________.
- 1027.The air charge leaving an intercooler, or aftercooler of an air compressor can be expected to be __________.
- 1028.Noise in a refrigeration compressor can be caused by __________.
- 1029.Thermal energy is commonly referred to as __________.
- 1030.Soldering flux aids the soldering process by __________.
- 1031.The cylinder unloading mechanism used on low pressure air compressors is an example of which mode of control?
- 1032.Valves used in the machinery space piping systems, and constructed with threaded valve stems, must be __________.
- 1033.Air trapped in the hydraulic fluid of a steering system would be indicated by __________.
- 1034.Which of the chisels listed should be used for cutting oil grooves?
- 1035.To determine the diameter of a small hole, which of the listed tools must be used with inside calipers to get an accurate reading?
- 1036.Flooding back' is a condition where the liquid refrigerant __________.
- 1037.The energy associated with molecules is known as __________.
- 1038.Flux is used when soldering, in order to __________.
- 1039.Which of the following proportional band values most closely approaches 'ON-OFF' control?
- 1040.Steam traps should be installed at the lowest outlet point of the heat exchanger in a horizontal run of pipe. Which of the following installation considerations should also be maintained?
- 1041.Over greasing of ball bearings installed on pumps will result in __________.
- 1042.Air trapped in the hydraulic fluid of a steering system should be indicated by __________.
- 1043.On small passenger vessels of less than 100 gross tons, watertight doors and watertight hatches are __________.
- 1044.While troubleshooting a refrigeration system for low head pressure, liquid refrigerant flooding back from the evaporator is determined to be the cause. It may be necessary to __________.
- 1045.A machine capable of producing 1650 foot-pounds of work per second is considered to produce how much horsepower?
- 1046.Soft solders have relatively low melting points and consist mainly of __________.
- 1047.Increasing the 'reset rate' of a proportional-plus-reset controller __________.
- 1048.Ball bearings may become overheated if they are __________.
- 1049.If a severe leak develops in the electro-hydraulic steering gear, which of the listed conditions could result?
- 1050.The best type of chisel to use for cutting a keyway is the __________.
- 1051.On small, low pressure, air compressors, the cylinders are usually lubricated by the __________.
- 1052.To correct the condition of slugging and flooding back in a refrigeration system, it may be necessary to __________.
- 1053.In a double-effect distilling plant, liquid moisture remaining entrained in the first-effect vapor, is removed by __________.
- 1054.Power is defined as the __________.
- 1055.When 'reset' action is added to proportional action, the proportional action __________.
- 1056.If a ball bearing for a centrifugal pump is completely packed with grease, __________.
- 1057.Which of the listed devices would be installed at a control system air pressure reducing station?
- 1058.Solder is an alloy of __________.
- 1059.Air line lubricators are used in compressed air systems to lubricate __________.
- 1060.In a double-effect distilling plant, the brine particles remaining entrained with the vapor produced in the evaporator first effect, are separated by __________.
- 1061.How much work would be accomplished if a 15 pound box were raised to the top of a 25 foot platform?
- 1062.When 'reset' action is added to proportional action __________.
- 1063.The basic function of a steam trap is to __________.
- 1064.In most pumps and pump motors, over packing the ball bearings full of grease will result in __________.
- 1065.When a vessel is in dry-dock, the vessel's engineers should __________.
- 1066.If you change from a low pour point lubricant to a high pour point lubricant in a refrigeration system, __________.
- 1067.Which of the following statements is correct when comparing the cylinder diameters of a two-stage reciprocating air compressor?
- 1068.The demisters installed in a flash-type evaporator serve to __________.
- 1069.Mechanical energy in transition is referred to as __________.
- 1070.The effect of 'reset', when added to a proportional controller is to __________.
- 1071.The basic function of a steam trap includes which of the following processes?
- 1072.A ball bearing will overheat if __________.
- 1073.The two most common gases used in pneumatic systems are __________.
- 1074.Intake valves installed on most reciprocating low pressure air compressors are actuated by the pressure differential between the air in the cylinder and the pressure __________.
- 1075.Badly leaking refrigeration compressor discharge valves will cause __________.
- 1076.In a two-stage flash-type distilling plant, the mesh-type vapor separators function to __________.
- 1077.What is the gain in potential energy of an object weighing 10 pounds when it is raised to a height of 10 feet?
- 1078.If a ball bearing installed on a pump is completely packed full of grease, this can result in __________.
- 1079.Separators are installed ahead of air line lubricators for the primary purpose of removing __________.
- 1080.In an oxy-acetylene welding outfit, each cylinder has a regulator and two pressure gages. One pressure gage indicates cylinder pressure and the other gage is used to indicate __________.
- 1081.In a refrigeration system equipped with a reciprocating compressor and a water cooled condensing unit, leaking compressor discharge valves will result in __________.
- 1082.The mesh type steam separators located in a two-stage flash distilling plant, function to __________.
- 1083.Which unit of measurement is used to measure mechanical potential energy?
- 1084.The control mode that is generally not used by itself is __________.
- 1085.A flash type evaporator is designed to operate in 75°F sea water, if operated in 50°F sea water, __________.
- 1086.The delivery rate of an axial-piston hydraulic pump is controlled by varying the position of the __________.
- 1087.When welding with an oxyacetylene outfit, __________.
- 1088.A reciprocating refrigeration compressor may be tested for leaking discharge valves by stopping the compressor, turning the discharge service valve all the way in, and then turning the compressor over by hand. If the discharge valves are leaking, the compound gage will show pressures __________.
- 1089.Small droplets of water entrained in the flashed vapor produced in a flash-type evaporator, are removed by the __________.
- 1090.Which of the following terms could be applied to the simple definition 'the energy of motion'?
- 1091.Reset control is also referred to as __________.
- 1092.In order to assure an output near the end of its compression stroke, the pressure developed in the high pressure cylinder of a reciprocating air compressor is __________.
- 1093.If the discharge valves on a refrigeration compressor are leaking badly, the compressor should __________.
- 1094.Referring to Coast Guard Regulations (46 CFR), the emergency bilge system __________.
- 1095.In order to prevent salt water contamination of the distillate in a flash-type evaporator, it is important to provide a positive seal around the __________.
- 1096.Reset control is also referred to as __________.
- 1097.Increasing the speed of a centrifugal pump will result in an increase in its capacity. Another means of increasing the capacity of a centrifugal pump is to increase the __________.
- 1098.The purging of air from an electro-hydraulic steering gear unit is necessary when __________.
- 1099.The piston displacement rate of a reciprocating air compressor can be modified by changing the __________.
- 1100.If a refrigeration system, equipped with a reciprocating compressor, has a solenoid valve that is leaking during the 'off' cycle, this could cause __________.