USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 14
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1301.An internal bypass is provided on some hydraulic system suction strainers to help reduce the possibility of __________.
- 1302.The range of values through which the input can be varied without initiating an output response is known as __________.
- 1303.Coast Guard Regulations (46 CFR) require fresh water tank vents which are open to the machinery space to terminate above the deep load waterline, unless the __________.
- 1304.If an anchor windlass has been idle for some time, you should __________.
- 1305.Water allowed to accumulate in the hydraulic system oil will cause an oxidation process producing by-products which are normally __________.
- 1306.It is possible to mount a double suction centrifugal pump impeller with the vanes facing in the wrong direction. This would cause the pump __________.
- 1307.The purpose of chill shocking an evaporator is to __________.
- 1308.If the speed of a drill is too great, the drill will __________.
- 1309.A thermostatic expansion valve is properly controlling evaporator superheat. Adjusting this valve to lower the superheat will result in a/an __________.
- 1310.Insulation on deck steam piping must be installed securely because __________.
- 1311.The value of the controlled variable, which under any fixed set of conditions the automatic controller operates to maintain, is known as __________.
- 1312.Air compressor receivers should be 'blown down' at least __________.
- 1313.Hydraulic machinery failures are commonly caused by misalignment of the system components and by __________.
- 1314.Which of the problems listed could happen if you attempted to force open a valve 'frozen' in position by using a wrench on the hand wheel?
- 1315.A double suction centrifugal pump impeller has been installed in the reverse direction, and will __________.
- 1316.If a centrifugal pump were continually operated with the discharge valve closed, the __________.
- 1317.When you adjust a thermostatic expansion valve __________.
- 1318.If water were a semisolid, the linear distance a propeller would advance in one revolution is the __________.
- 1319.To ensure adequate lubrication and to prevent a high operating temperature, the recommended amount of grease injected into a ball or roller bearing is approximately __________.
- 1320.When the pressure applied to a Bourdon tube-type pressure gage is reduced to atmospheric pressure, the tube will begin to 'bend' towards the center of arc. Small variations develop preventing the tube from returning to its exact original shape due to the process known as __________.
- 1321.The shaft sleeves have recently been replaced on a centrifugal salt water service pump. The packing gland is now drawn tightly up against the casing. Despite the use of standard procedures to tighten the packing gland, water continues to pour out along the shaft. The probable cause for this situation is that __________.
- 1322.Your Coast Guard engineer's license __________.
- 1323.Hydraulic machinery failures are commonly caused by contamination of the hydraulic fluid and __________.
- 1324.A weld with triangular cross sections is used to join two surfaces at right angles to each other, and is called a __________.
- 1325.Before drilling a hole in a piece of metal, the location of the hole center should be __________.
- 1326.The refrigeration system low pressure cutout switch is actuated by __________.
- 1327.The movement of steam piping, as a result of changes in temperature, is compensated for by the use of __________.
- 1328.Traps at plumbing drain connections prevent __________.
- 1329.Devices, such as a pressure gage, that are subject to continuous expansion and contraction are affected by hysteresis. This is a natural process that __________.
- 1330.In an automated control system, which of the following statements would apply to any type of closed loop system?
- 1331.A knocking sound emitted from an unloaded air compressor is probably caused by __________.
- 1332.Which of the following statements is true concerning low pressure distilling units?
- 1333.A piece missing from one blade of a four-bladed propeller could result in __________.
- 1334.The sensing line for the low pressure cutout switch to a refrigeration system is located __________.
- 1335.A taper tap is correctly used for __________.
- 1336.Which type of screwdriver listed would have a 'Keystone' type vertical cross-sectional tip?
- 1337.In the production of freshwater from seawater through a process of heating and cooling, the cooling phase of production is usually called __________.
- 1338.Which of the listed metals can usually be drilled without lubrication?
- 1339.All straight shanked twist drills must be mounted or held in a __________.
- 1340.The low pressure cutout switch used on a refrigeration system compressor is set to cut in at approximately 5 psig and cutout at __________.
- 1341.Excessive propeller vibration may occur as a result of __________.
- 1342.Small passenger vessel of less than 100 gross tons shall be dry-docked or hauled out at intervals not to exceed 36 months if it is operated in saltwater a total of___________.
- 1343.Information from a data-logger can be helpful in determining the long term probability of machinery failure if you __________.
- 1344.A Coast Guard engineer's license can be suspended or revoked for __________.
- 1345.The process of boiling seawater in order to separate it into freshwater vapor and brine is usually defined as __________.
- 1346.If the cutting edges of a drill are ground at different angles, the __________.
- 1347.The purpose of the low pressure cutout switch is to __________.
- 1348.Partially clogged or scored nozzles in a two stage air ejector unit of a flash distilling plant could result in a __________.
- 1349.In modern ship construction, high tensile steel (HTS) may be permitted in __________.
- 1350.A check run on a hydraulic anchor windlass during long periods of inactivity should be carried out to __________.
- 1351.If two centrifugal pumps, driven by two independent electric motors, operating at unequal speeds are discharging an inflammable liquid through a common discharge line, the higher speed pump may cause the slower pump to __________.
- 1352.The dimension of the thinnest hydrodynamic film developed within a full journal bearing, when all other factors remain constant, depends upon the __________.
- 1353.The purpose of the refrigeration system low pressure cutout switch is to __________.
- 1354.Mechanical shaft seals used on water service pumps require lubrication of the seal faces to minimize deposits of foreign matter on those surfaces. Which of the following pressures and lubricants are required?
- 1355.Which of the following conditions can develop if a valve with a badly scored valve stem is repacked?
- 1356.Which of the following statements best describes a 'Keystone' shaped tip on a standard screwdriver?
- 1357.Overheating of a hydraulic system may be a result of __________.
- 1358.Condensate must be drained periodically from the air compressor receivers to prevent __________.
- 1359.When a flash-type evaporator is to be secured for an extended period of time, the entire unit should be drained, cleaned, and __________.
- 1360.Rapid wear on the extreme outer corners to the cutting edges of a drill bit is the result of the drill having __________.
- 1361.The oil separator (trap) used in a large shipboard refrigeration system would be located between the __________.
- 1362.Which of the following types of nuts would be best suited to use when it is important that a nut not work itself loose due to vibration?
- 1363.In pressure measurement, absolute pressure is defined as the difference in pressure between __________.
- 1364.According to Coast Guard Regulations (46 CFR), a fresh water evaporator is classified as a/an __________.
- 1365.The nameplate of a reciprocating pump lists the following dimensions: "7 X 6 X 4". The diameter of the liquid cylinder is __________.
- 1366.Which of the following nondestructive testing methods can be used to detect a suspected subsurface defect in a tail shaft liner?
- 1367.The neutralization number obtained from a test sample of lubricating oil will tell you precisely __________.
- 1368.An oil separator is a device used to remove oil from the __________.
- 1369.A decision has been made to change out 1,000 gallons of lube oil in a vessel's main propulsion unit. Which of the following statements is true regarding this decision?
- 1370.In an automation system, the effect of a control action sensed by a controller is known as __________.
- 1371.Purging air from a hydraulic system is necessary when __________.
- 1372.Which of the following statements concerning deep well cargo pumps is correct?
- 1373.Joiner bulkheads on a MODU provide __________.
- 1374.Oil separators installed in refrigeration systems serve to __________.
- 1375.The brine density in a submerged tube evaporator should be maintained at __________.
- 1376.A screwdriver should never be used as a __________.
- 1377.Which of the following conditions will prevent a shipboard pump from achieving its maximum suction lift?
- 1378.Structural bulkheads on a MODU are usually __________.
- 1379.Plug valves installed in hydraulic systems are most suitable for use as __________.
- 1380.In a disk-type lubricating oil purifier, __________.
- 1381.Properties of a good refrigeration oil include __________.
- 1382.Pushing the file endways (or with the axis), under pressure, against the work, is called __________.
- 1383.The lignum vitae in a stern tube bearing is normally lubricated with __________.
- 1384.Which of the following guidelines is considered to reflect good design practices for shipboard steam heating systems?
- 1385.To anneal a copper gasket, you should heat the gasket __________.
- 1386.Reinforcing frames attached to a bulkhead on a MODU are called __________.
- 1387.Hydraulically, servo-operated, automatic, change over valves, utilized in a two ram hydraulic steering gear, serve to __________.
- 1388.Ball peen hammers are sized according to their __________.
- 1389.If a stateroom has a 6" by 12" opening through which air travels at 100 feet per minute, what is the volume of air being supplied to the stateroom?
- 1390.Liquid is kept from leaking out at the shaft ends of a helical gear pump by __________.
- 1391.The stern tube flushing connection can be used to __________.
- 1392.A Bourdon tube-type steam pressure gage is fitted with a siphon loop to prevent damage from the direct effects of __________.
- 1393.The size of the discharge ring used for the efficient operation of a disk type purifier is dependent upon the __________.
- 1394.A vessel is in compliance with federal regulations regarding the discharge of sewage by __________.
- 1395.In MODU construction, beams are transverse girders which provide support to __________.
- 1396.If a stateroom has a 5 inch by 12 inch opening through which the air travels at 100 feet per minute, what is the volume of air being supplied to the stateroom?
- 1397.Which of the following statements is true regarding mechanical seals?
- 1398.The number "8" in the notation of an '8-32' tap, indicates the __________.
- 1399.File lengths are determined by the __________.
- 1400.Which of the following is the most common type of valving element used in hydraulic system directional control valves?