USCG Engineering General Subjects – Question Bank Book 11 (BK11) — page 6
3080 questions with correct answers from the official USCG question bank (2008 edition), book 11 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 501.When it is necessary to repair a refrigeration system using R-134A and the system will be open for more than a few minutes, the open ends of the system should be __________.
- 502.The 'pitch' of a screw is the __________.
- 503.The use of a needle valve in a piping system is recommended when requiring __________.
- 504.A constant hissing sound at the thermal expansion valve will always indicates __________.
- 505.In a two stage flash type evaporator, the brine overboard pump is vented directly to the __________.
- 506.If an air compressor is used to supply air primarily to the combustion control system and other pneumatic controllers, the entire system is known as the __________.
- 507.A shot of anchor chain has a length of __________.
- 508.Air entrained in the hydraulic fluid, or trapped in an actuator will cause the actuators to move with a jerky motion. This action is a result of __________.
- 509.When replacing packing rings in the stuffing boxes of reciprocating pump piston rods, the ends of the rings should be cut __________.
- 510.Hydraulic system tubing should be anchored every three or four feet to prevent __________.
- 511.A cracked diaphragm in a thermostatic expansion valve will cause the valve to __________.
- 512.In order to distribute the side pressures over a wide area of the cylinder walls and liners, which of the listed types of pistons are used in modern low pressure air compressors?
- 513.Which of the listed operating conditions would have the greatest effect on the volumetric efficiency of an operating reciprocating air compressor?
- 514.Which of the listed systems related to an engineer's signal alarm panel is required to be indicated by a continuously illuminated light while in operation?
- 515.Which of the following is the minimum internal diameter of the main bilge suction piping permitted by Coast Guard Regulations (46 CFR Part 56) on a vessel over 150 gross tons?
- 516.Broken valve strips in an operating low pressure air compressor will cause __________.
- 517.During the inspection of a low pressure pump, the wearing ring is determined to have a clearance of 0.011" - 0.013", you should __________.
- 518.Which of the problems listed represents the major difficulty encountered with thermal expansion valve operation?
- 519.What basic dimensions are used in describing machine bolts?
- 520.A viscous film of oil collected between the valve face and seat of a low pressure reciprocating air compressor will __________.
- 521.Short cycling of the potable water system's pump is prevented by using __________.
- 522.If the pump for a hydraulic anchor windlass is over heating, the cause may be __________.
- 523.Compared to poppet and other mechanically operated valves, which of the following advantages is gained by using a thin plate (feather) low lift type valve in an low pressure air compressor?
- 524.According to Coast Guard Regulations (46 CFR), where cargo pump shafts on tankers pierce bulkheads __________.
- 525.If a refrigeration compressor were short cycling on the low pressure cutout switch, the probable cause for this might be the __________.
- 526.Machine bolts are identified by their __________.
- 527.A metal file has become clogged with filings and should be cleaned with a file __________.
- 528.The function of the springs used with channel or plate-type valves for reciprocating air compressors is to __________.
- 529.Where should you expect to find striking plates on liquid storage tanks?
- 530.The part of the anchor windlass that engages the anchor chain for lifting is called the __________.
- 531.Air blowing from the intake air filter of an operating air compressor indicates __________.
- 532.Which of the listed valve types is typically used for suction and discharge valves on modern low pressure air compressors?
- 533.When any low pressure distilling plant is operated with less than the designed vacuum, the __________.
- 534.If a refrigeration crankcase compressor were short cycling on the low pressure cutout switch, the cause might be that the __________.
- 535.Heavy pressure on the ends of a file will cause the work surface to become __________.
- 536.Which of the valves listed will be cycled from fully open to fully closed when the handle is turned 90°?
- 537.Which of the following problems would be the probable cause for the faulty operation of a reciprocating air compressor suction valve?
- 538.In which of the listed hydraulic systems will the installation of an oil cooler be necessary?
- 539.In accordance with Coast Guard Regulations (46 CFR), a steam propelled cargo vessel over 25 gross tons may have a Certificate of Inspection issued for __________.
- 540.Which of the following problems could cause air to blow out through the inlet air filter of a running compressor?
- 541.A refrigeration unit will tend to short cycle when operating __________.
- 542.A vacuum is initially created in a flash type distilling plant by __________.
- 543.Most pump manufacturers recommend that the discharge piping for centrifugal pumps be one size larger than the pump discharge nozzle to __________.
- 544.The principal purpose of an anchor windlass chain stopper is to __________.
- 545.Which of the following problems can result in below normal pressure in the intercooler of an operating low pressure air compressor?
- 546.If a refrigeration compressor is short cycling on high head pressure, you should __________.
- 547.Which of the listed tools should be used to remove a tapered roller bearing from a shaft?
- 548.Most pump manufacturers recommended that the discharge piping for centrifugal pumps be __________.
- 549.If all of the air charge has been lost from a ship service air receiver, the compressor mechanical unloading system will __________.
- 550.If the fixed orifice in the evaporator steam supply line were to be removed, the steam pressure reducing valve located upstream would __________.
- 551.Every automated machinery plant must have an 'engineer's assistance' alarm. Power for this alarm should be taken from the __________.
- 552.Excessively low air pressure occurring in the intercooler of a reciprocating air compressor is caused by __________.
- 553.If you install a hydraulic hose on a unit and fail to leave sufficient room for expansion, which of the following problems will develop?
- 554.The refrigeration compressor in a water cooled refrigeration system is short cycling on the high pressure cutout switch. One reason for this could be the __________.
- 555.In the operation of a flash type evaporator equipped with air ejectors, the air and non-condensable gases are evacuated directly from the __________.
- 556.Most pump manufacturers recommend that the suction piping dimension for centrifugal pumps be __________.
- 557.The usual method of unloading a low pressure air compressor at start-up is accomplished by __________.
- 558.Hydraulic systems typically operated for intermittent service do not require the use of oil coolers and would include all of the following except _________?
- 559.Slipping drive belts on a ship service air compressor is a probable symptom of __________.
- 560.If you install a new hydraulic hose in a hydraulic system, the hose must be long enough to allow for contraction to prevent __________.
- 561.The refrigeration system compressor is short cycling on high head pressure when the sea water cooling temperature is 72°F. In this situation, you should __________.
- 562.The proper file for a finishing cut on soft metal, such as brass, is the __________.
- 563.Unloading of a low pressure, reciprocating, air compressor at start-up can be accomplished by __________.
- 564.If one of the bilge manifold valves is prevented from seating, the __________.
- 565.The location of a vessel's frame stations may be obtained from which of the listed drawings?
- 566.Which of the following precautions should always be carried out in dry-dock?
- 567.If an electric motor driven air compressor fails to start, it may be due to a __________.
- 568.Machinery driving fuel oil transfer and fuel oil service pumps must be fitted with a remote means of stopping the machinery from __________.
- 569.The compressor in an air-cooled condensing refrigeration system is short cycling on the high pressure cutout switch. A probable reason for this is the __________.
- 570.The efficiency of a flash type evaporator can be increased by __________.
- 571.Open end wrenches are __________.
- 572.An air compressor can be unloaded at start-up by__________.
- 573.Which of the following actions should be taken FIRST if a bilge well of a multiple suction bilge system is unable to be pumped out?
- 574.Why do roller bearings have higher loading capacities than ball bearings?
- 575.With regards to fluid flow control, an advantage of pneumatic control systems over electrical control systems is __________.
- 576.The seat of a butterfly valve will most likely be constructed of __________.
- 577.Flexible hose under pressure in a hydraulic system will __________.
- 578.The compressor in the ship service refrigeration system is short cycling on the high pressure cutout switch. The probable reason for this is the __________.
- 579.Which of the following statements describes the relationship between flash point and ignition temperature?
- 580.On tank vessels using an automatic tape wells, free movement of the tape is normally checked by __________.
- 581.Coast Guard Regulations (46 CFR) require remote controls for stopping fuel oil service pumps. These controls shall be __________.
- 582.If a refrigeration compressor will not start, the reason may be __________.
- 583.The lowest temperature required to cause self-sustained combustion of a substance independent of any outside source of ignition is called __________.
- 584.The aft starboard bilge well is clogged, and back flushing has not been successful. The next practical solution would be to __________.
- 585.On tank vessels using an automatic tape well for gaging tanks, the hand clutch is used to __________.
- 586.Automatic pressure control valves for steam service require periodic maintenance inspections because they __________.
- 587.Double cut files are most effective when used for__________.
- 588.When a refrigeration compressor motor fails to start, the FIRST thing that should be checked for is a __________.
- 589.Air compressors are equipped with unloading systems for the purpose of ____________________.
- 590.The simplest method to use for determining if a centrifugal pump is operating as designed, is to __________.
- 591.The pressure of an operating hydraulic system, as indicated by a pressure gauge, is a result of the fluid flow overcoming __________.
- 592.Which of the following statements concerning butterfly valves is correct?
- 593.The names plug, bottom, and taper refer to __________.
- 594.One of three available centrifugal salt water service pumps is in operation with a sea water temperature of 50°F. The cooling temperature of all systems supplied by this pump appear to be high. Therefore, you should __________.
- 595.Pressure in an operating hydraulic system is developed __________.
- 596.On small passenger vessels, separation of machinery and fuel tank spaces shall be __________.
- 597.Which of the listed types of files is the best for producing a fine finish on metal?
- 598.Which of the following systems, according to Coast Guard Regulations (46 CFR) must have an emergency stop, protected with a glass enclosure, and located outside of the machinery space?
- 599.The accumulation of air and other non-condensable gases in a refrigeration system will __________.
- 600.Which pump installation would require an external source of sealing water?