USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14)
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1.Precision engine bearing inserts are manufactured with a small portion of the bearing ends extending beyond the bearing housing or caps. The installation process of these bearings requires sufficient __________.
- 2.Where is a fusible plug installed on a Scotch or auxiliary boiler?
- 3.Bearing wear on a split sleeve type bearing is normally measured with a __________.
- 4.The amount of wear on a split precision main bearing can be accurately determined by comparing the data from a previous reading to the present readings taken with a __________.
- 5.The amount of wear on a split, fixed sleeve-type, main diesel bearing can be accurately determined with a __________.
- 6.Crank web deflection readings will give a positive indication of __________.
- 7.When a diesel engine is equipped with a hydraulic starting system designed to operate at pressures of 150 psi or more, Coast Guard Regulations (46 CFR) require that the hydraulic fluid shall __________.
- 8.What preventative maintenance should be done frequently to diesel engine starting air receivers?
- 9.Coast Guard Regulations (46 CFR) permit drain valves in the machinery space for removing water and impurities from diesel engine fuel systems. Those valves must be __________.
- 10.Where diesel engine speed and clutch controls are combined into one operation by a single control lever, movement of the lever from the 'stop' position to the 'ahead' position will FIRST __________.
- 11.In comparison to exhaust valves, intake valves of diesel engines may be fabricated from low-alloy steels because __________.
- 12.Fusible plugs are installed in fire-tube boilers to __________.
- 13.Friction developing between the moving parts of a governor, governor linkage and control valve will cause the governor to __________.
- 14.Which of the bearings listed are most widely used for the main and connecting rod bearings of a diesel engine?
- 15.Coast Guard Regulations (46 CFR) permit the use of drain valves for removing water or impurities from diesel engine fuel systems. These valves must be __________.
- 16.Which of the following methods is normally used to lubricate bearings in a small high-speed diesel engine?
- 17.A large change in ambient temperature, or using an oil of a viscosity different than the one recommended by the manufacturer in a mechanical hydraulic governor, will result in the need to adjust the __________.
- 18.To check the setting of the overspend trip on a diesel powered generator, you would use a __________.
- 19.Which of the following is an example of a solid bearing?
- 20.Coast Guard Regulations (46 CFR) require steel tubing connections and fittings used with diesel fuel oil systems, to be either flared or __________.
- 21.In an auxiliary diesel engine bypass type lubricating oil system, the main lube oil pump forces __________.
- 22.In a bypass type filtering system for a medium or high speed diesel engine, the lube oil bypassing the filter __________.
- 23.Two important considerations for the proper lubrication of a diesel engine include, the delivery of the oil in sufficient amount, and the __________.
- 24.In a diesel engine, the main bearings are used between the __________.
- 25.The replacement piping for diesel engine high pressure fuel systems must be the same length and diameter as the original piping to __________.
- 26.Heat exchangers are most commonly found in a small auxiliary diesel engine __________.
- 27.Diesel engine jacket water is used in the fresh water distillation process as the __________.
- 28.Multiple concentric valve springs are often used with diesel engine valves to __________.
- 29.A controllable pitch propeller on a diesel driven vessel eliminates the need for __________.
- 30.When the prime movers of two paralleled generators are equipped with mechanical-hydraulic governors, and are operating within their designed range, the unit with the least amount of speed droop will __________.
- 31.Which of the listed bearing installations is subjected to swinging motion?
- 32.To prevent vibration damage to the fuel supply line of a diesel engine, you may use __________.
- 33.One advantage of a vacuum feed sight glass indicator used on cylinder lubricators over the discharge side liquid filled type sight glass is __________.
- 34.If the combustion control system of an automatically fired auxiliary boiler fails to sustain burner ignition after a normal shutdown, you should check for a/an __________.
- 35.The term 'PLAN/33,000' is equal to the __________.
- 36.Bearing 'crush' as applied to diesel engine main bearings, will result in __________.
- 37.Which of the listed types of gasket material should be used on high pressure fuel oil lines on a diesel engine?
- 38.Motor vessels usually have independent lube oil systems for main engine and main reduction gears because __________.
- 39.Clearance volume scavenging in a turbocharged, four-stroke/cycle diesel engine is accomplished __________.
- 40.Mist detectors used on large low-speed and medium speed main propulsion diesel engines monitor and check for the presence of __________.
- 41.A main propulsion diesel engine crankshaft bearing lacking sufficient 'crush', will __________.
- 42.Which of the bearings listed is most widely used for main and connecting rod bearings of modern diesel engines?
- 43.Directional intake ports in diesel engines are used to __________.
- 44.Before any work is to be carried out on a burner in an automatically fired auxiliary boiler, you should always __________.
- 45.Generating tubes in waste heat boilers are finned to __________.
- 46.If an operating auxiliary boiler has a water pH reading of 7, you should __________.
- 47.Which of the following conditions is responsible for the fuel oil to atomize when using a steam atomizer in an auxiliary boiler?
- 48.Diesel engine main and connecting rod precision bearings are made in halves. Each half exceeds one-half the bearing circumference by a small amount. The small amount is termed __________.
- 49.Fuel is admitted to a diesel engine cylinder through the __________.
- 50.The piston rod scraper box incorporated in a two-stroke/cycle, crosshead diesel engine serves to __________.
- 51.A failure to any component of a flame safeguard control for an automatically fired auxiliary boiler, will result in __________.
- 52.When an auxiliary boiler is on the line, the output of the flame scanner can be checked by placing a micro ammeter in series with the photoelectric cell circuit. The readings on high fire should be __________.
- 53.A feed pump for an auxiliary boiler might lose suction if the __________.
- 54.The proper location for journal bearing oil grooves is __________.
- 55.How are hydraulic valve lash adjusters on diesel engine rocker arm assemblies lubricated?
- 56.Trunk-type diesel engine pistons are most effectively cooled by heat __________.
- 57.The amount of oil consumed by a return flow-type fuel atomization system, fitted with both supply and return meters, can be determined by the __________.
- 58.Main propulsion diesel engines having a bore exceeding 300 mm are to have at least __________.
- 59.The water in a steaming auxiliary boiler should be tested daily for __________.
- 60.The programmed control system of an automatic auxiliary boiler will terminate the light off process during the pre-purge period if air flow is not sensed and __________.
- 61.Integral water jacket liners use O-rings near the bottom of the liner. These O-rings serve to __________.
- 62.Reduction gear lube oil temperatures for keel cooler installations are generally __________.
- 63.Microbiological growths in marine fuel are a common occurrence that can be __________.
- 64.The flame safeguard control system of a large automatic auxiliary boiler will provide fuel shut off in the case of high __________.
- 65.A characteristic of a bearing material which permits small dirt particles to become embedded in the bearing surface is __________.
- 66.The start of fuel oil injection into the cylinder of a four-stroke/cycle diesel engine occurs during the __________.
- 67.Lube oil pumps taking suction from the sump of most small marine engines are usually __________.
- 68.A large, low-speed, main propulsion diesel engine uses sea water to directly cool the __________.
- 69.The total starting air capacity required for reversible main engines is to be sufficient for a least __________.
- 70.Most fuel injection nozzles are opened by __________.
- 71.The lube oil pump used in a diesel engine is normally a __________.
- 72.The boiler water alkalinity in a coil-type auxiliary boiler should be maintained at the pH recommended by the boiler manufacturer to __________.
- 73.Coast Guard Regulations (46 CFR) require the controls for automatically fired auxiliary boilers, must be fitted with visible indicators to signal __________.
- 74.When a waste heat boiler is installed in the exhaust of a main propulsion diesel engine, the exhaust gas bypass would be used __________.
- 75.How is the concentration of dissolved oxygen in the feed water of an auxiliary boiler maintained at acceptable limits?
- 76.Fuels as produced in a refinery are generally sterile, however, contamination can occur as fuels are __________.
- 77.Which of the listed types of control systems is required by Coast Guard Regulations (46 CFR) for large automatic auxiliary boiler heating equipment?
- 78.Which component will receive the greatest load in a two-stroke/cycle diesel engine?
- 79.Injection pressure in a common rail fuel system is controlled by __________.
- 80.Maximum lube system operating pressure for a diesel engine is normally regulated by a/an __________.
- 81.Which of the following is necessary for all waste heat boiler installations, regardless of design or manufacturer?
- 82.A naturally aspirated diesel engine at full throttle will have an intake manifold pressure __________.
- 83.When replacing tubes in a water-tube auxiliary boiler, to eliminate the possibility of leaks at the tube seats, the replacement tubes should be __________.
- 84.In order for microbiological growths to thrive in a fuel tank it is necessary for __________.
- 85.Which of the statements represents a characteristic of the thrust collar in a Kingsbury thrust bearing?
- 86.During the fuel injection period, fuel pressure must exceed cylinder gas pressure to __________.
- 87.The output pressure of a diesel engine lube oil pump is regulated by a/an __________.
- 88.Automatic combustion control systems for some auxiliary boilers are designed to cycle burners on in response to __________.
- 89.The over speeding of the diesel engine driving an electric generator could cause __________.
- 90.An increase in the air inlet manifold pressure of a diesel engine will result in a/an __________.
- 91.It is desirable for an auxiliary boiler safety valve to pop open and reseat firmly to __________.
- 92.Coast Guard Regulation (46 CFR) requires that after undergoing extensive repairs, an auxiliary boiler, with a maximum allowable working pressure of 60 psig (411.89 kPa), should be hydrostatically tested at a pressure of __________.
- 93.The purpose of the programmed purge cycle on an automatically fired auxiliary boiler is to __________.
- 94.An auxiliary boiler equipped with a return flow fuel atomization system, has a __________.
- 95.The leveling plates in a Kingsbury thrust bearing are held in position by __________.
- 96.For a continuous operation diesel engine, a duplex filter unit would be the best arrangement because __________.
- 97.Which of the following devices controls the discharge flow rate of an attached, positive displacement, rotary gear, diesel engine, lube oil pump?
- 98.The expansion tank for a diesel engine closed cooling system is designed to maintain a constant head on the system and __________.
- 99.Why are heavy fuels not usually prone to the problems of microbiological infection?
- 100.Heavy soot accumulations in an auxiliary boiler could be caused by __________.