USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 10
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 901.Which of the following statements represents the function of the compression rings installed at the top of a diesel engine piston?
- 902.Because of the close tolerances used in diesel engine fuel oil pumps, a worn plunger requires __________.
- 903.If the oil control rings were installed upside down on a diesel engine piston, which of the following conditions would result?
- 904.A diesel engine emits blue exhaust smoke as a result of __________.
- 905.If a diesel engine is smoking excessively under load, the cause could be __________.
- 906.A diesel engine exhaust valve spring is under compression when __________.
- 907.If the diesel engine starter-drive mechanism fails to disengage after the engine starts, which of the following situations will occur?
- 908.The highest loads applied to the diesel engine crankshaft main bearings are __________.
- 909.During which of the listed piston strokes of a four-stroke/cycle diesel engine, is the piston moving downward?
- 910.Combustion gases formed in the cylinder of a diesel engine are prevented from blowing past the piston by __________.
- 911.While overhauling a jerk-type fuel pump it is necessary to replace the pump plunger. Which of the parts listed below must also be replaced?
- 912.The purpose of the flywheel is to __________.
- 913.An emergency diesel generator should automatically shut down in the event of __________.
- 914.Increasing the compression ratio of a diesel engine while maintaining the designed rate of fuel flow will result in __________.
- 915.Black smoke exhausting from an operating diesel engine is an indication of poor combustion which may be caused by __________.
- 916.Which of the following statements is correct concerning available astern power for diesel main propulsion systems?
- 917.In a modern internal combustion diesel engine, the load carrying part of the engine is referred to as the __________.
- 918.If the plunger or barrel of a fuel injection jerk pump becomes damaged, __________.
- 919.A well-lubricated bearing surface always appears __________.
- 920.Waste heat boilers may be equipped with vents on the feed water heater heads to __________.
- 921.Provision is to be made for ventilation of an enclosed diesel engine crankcase by means of a small __________.
- 922.According to U. S. Coast Guard Regulations (46 CFR), internal combustion engine driven emergency generators shall be operated under load for at least two hours at least once __________.
- 923.If the detergent type lubricating oil being used in a diesel engine is black, the oil __________.
- 924.Coast Guard Regulations (46 CFR) require emergency diesel generator sets, with forced lubrication systems, to be provided with a __________.
- 925.The side clearance of the compression rings on diesel engine pistons is necessary to __________.
- 926.Which of the following conditions is indicated when the lubricating oil of a diesel engine turns dark after a few hours of use?
- 927.A propulsion diesel engine, having a maximum continuous output of over 300 HP, and driving a controllable pitch propeller, must be fitted with a separate over speed device, in addition to the normal governor. This second device is to prevent the engine from exceeding the rated speed by more than __________.
- 928.In an internal combustion engine, which of the devices listed will force the compression rings to seal the compression gases in the space above the piston?
- 929.When disassembling or assembling an injection pump plunger and barrel you should __________.
- 930.Oil oxidation, as a result of excessively high lube oil temperature, is harmful to a diesel engine because __________.
- 931.According to Coast Guard Regulations (46 CFR), how often shall internal combustion engine driven emergency generators be operated under load?
- 932.In an operating diesel engine, the sealing of the cylinder is the result of the compression rings being forced against the cylinder walls by __________.
- 933.Surface irregularities, such as erosion and pitting on injection pump plungers, will __________.
- 934.The oxidation by-products forming in diesel engine lube oil can cause __________.
- 935.In a large slow-speed propulsion diesel engine, the force applied to the crosshead is __________.
- 936.Coast Guard Regulations (46 CFR) require a horizontal dry exhaust pipe from a diesel engine must __________.
- 937.Uneven bolt tightening during the installation of a fuel injection pump can result in __________.
- 938.Which of the following operational conditions will occur to the diesel engine lube oil at extremely high temperatures?
- 939.Coast Guard Regulations (46 CFR) require a horizontal dry exhaust pipe from a diesel engine to __________.
- 940.The purpose of end clearance on a diesel engine piston ring is to __________.
- 941.If lost motion is present in an individual fuel injection pump, which of the following problems will occur?
- 942.Which of the listed conditions can cause a diesel engine to use too much lube oil?
- 943.A diesel engine is driving an alternator required to run at 1800 RPM. The over speed governor is normally required to be set within a range of __________.
- 944.Excessive lube oil consumption in a diesel engine can be caused by __________.
- 945.In diesel engines, hydraulic valve lifters are used to __________.
- 946.Which of the following problems can cause excessive consumption of the lubricating oil in a diesel engine?
- 947.Auxiliary diesel engines can be automatically shut down as a result of __________.
- 948.Valve lash, or clearance refers to the __________.
- 949.Excessive piston ring wear in a diesel engine will cause __________.
- 950.Sticking of diesel engine piston compression rings may be caused by __________.
- 951.What is the purpose of a hydraulic valve lash adjuster?
- 952.If a diesel engine runs roughly, which of the systems listed is most likely to be at fault?
- 953.Worn diesel engine intake valve guides can result in __________.
- 954.Diesel engine valve springs function to __________.
- 955.In the common rail system, excessive pressure in the header may be caused by __________.
- 956.Which of the following conditions can cause excessive lube oil consumption in a diesel engine?
- 957.The intake and exhaust valves used in a diesel engine are returned to their seats by __________.
- 958.When a leak has developed in the lube oil cooler of an operating diesel engine, which of the listed operating conditions can be expected to occur?
- 959.A six cylinder, two stroke/cycle diesel engine is 83% efficient and has a cylinder constant of 0.998 while operating with a mean effective pressure of 15 kg/cm2 at a speed of 100 RPM. What is the metric brake horse power developed?
- 960.If the jacket water temperature rises rapidly above normal in a diesel engine, you should FIRST __________.
- 961.According to Coast Guard regulations, keel cooler installations are __________.
- 962.Valve cages are used on some large diesel engines to __________.
- 963.If the manufacturer advises of a normal lube oil consumption for a 4000 horsepower (2982.8 kW) diesel engine to be .0001 gal/hp-hr, (.5076 mL/kW-hr), how much oil should the engine consume in one 24 hour period if operated at full load?
- 964.The tube sheets installed in a fire-tube auxiliary boiler are normally connected by __________.
- 965.Under normal operating conditions, the main source of crankcase oil contamination in medium speed diesel engines is attributed to __________.
- 966.In a diesel engine, a cylinder liner should be replaced if it is __________. I. scuffed II. scored
- 967.In a diesel engine cooling system, the high temperature alarm contact maker will be activated on excessively high water discharge temperature from the __________.
- 968.Cooling water pumps driven by direct reversing diesel engines are usually of the straight impeller vane type pump with a concentric housing to __________.
- 969.During engine warm-up, the expansion of cylinder head valve stems due to the buildup of engine heat, is compensated for by the __________.
- 970.In an operating diesel engine, preignition can be caused by __________.
- 971.Excessive lube oil consumption can result from worn or broken __________.
- 972.In a diesel engine, an integral liner is one in which the cooling water __________. I. flows through the cylinder liner jackets II. touches the outer side of the liner
- 973.In a diesel engine, when refitting piston rings you should__________. I. check the ring gap at the smallest diameter of the cylinder II. remove carbon from the ring groove
- 974.What is the metric brake horse power developed per cylinder by an 83% efficient, six cylinder, two-stroke/cycle diesel engine with a cylinder constant of 0.998 and a mean effective pressure of 15 kg/cm2 at 100 RPM?
- 975.A condition that can increase the foaming tendency of lube oil is __________.
- 976.If the diesel engine fuel injection timing is changed to delay the start of injection until the pistons are at top dead center, the engine will __________.
- 977.Excessive lubricating oil consumption in a running diesel engine can be caused by __________.
- 978.Which of the following conditions is likely to develop if the thermocouple element of a pyrometer becomes coated with excessive amounts of combustion by-products?
- 979.What is the swept volume per cylinder per revolution of a six-cylinder, two-stroke/cycle diesel engine with a 580 mm bore and a 1700 mm stroke operating at 100 RPM?
- 980.A seven cylinder, two-stroke/cycle, single acting diesel engine with a cylinder indicated horsepower calculated as 1350 kW and brake horsepower measured at 7466 kW has a mechanical efficiency of __________.
- 981.In a diesel engine, the spring force required for proper valve operation is determined by __________.
- 982.In a four-stroke/cycle diesel engine, badly worn intake valve guides can cause excessive __________.
- 983.Forcing the exhaust gases from the cylinder of an operating two cycle diesel engine with the aid of a blower is known as __________.
- 984.An acceptable means of tightening connecting rod and main bearing cap bolts is to measure the __________. I. torque applied to each nut and bolt assembly II. stretch of each nut before and after tightening
- 985.A condition contributing to diesel engine piston rings sticking in the ring grooves, is insufficient ring clearance at the ring __________. I. Gap II. Side
- 986.In a trunk type diesel engine piston, the thickness of the head or crown is determined by the __________. I. strength requirement II. heat dissipation requirement
- 987.A crankshaft whose center of gravity coincides with its center line is said to be __________. I. statically balanced II. dynamically balanced
- 988.A seven cylinder, 2-stroke/cycle, single acting diesel engine has a 750 mm bore and a 2000 mm stroke. What indicated power will be developed if the average mean effective pressure is 14.8 kg/cm2 at a speed of 96 RPM?
- 989.Late fuel oil injection in a diesel engine can result in __________.
- 990.Which of the following problems represents one possible cause of high lube oil consumption in a four stroke diesel engine?
- 991.The formula 'Nplan/33,000' is equal to the __________.
- 992.At bottom dead center, the centerline of the connecting rod usually coincides with the __________.
- 993.In a diesel engine, when installing new piston rings it is important to check __________. I. ring gap clearance II. side clearance
- 994.A six cylinder 2-stroke/cycle, single acting diesel engine has a 580 mm bore and a 1700 mm stroke. What indicated power per cylinder will be developed if the average mean effective pressure is 15.3 kg/cm2 at a speed of 120 RPM?
- 995.When fuel is injected late into a diesel engine cylinder, __________.
- 996.When using a fuel with a higher than normal sulfur content in an auxiliary diesel engine, you should __________.
- 997.Which of the following cylinder scavenging methods will include an exhaust valve located in the cylinder head?
- 998.In a diesel engine, the piston compression rings make contact with the __________. I. back of the ring groove II. bottom of the ring groove
- 999.The purpose of an interference angle in a diesel engine exhaust valve is to __________. I. work in conjunction with valve rotators to rotate the valve II. break up seat deposits
- 1000.Which of the listed devices could be used as a substitute for a ring grooving tool?