USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 17
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1601.Corrosion and grooving on the blading of an exhaust driven turbocharger is caused by certain components of residual fuel oils. These components are vanadium, sodium, and __________.
- 1602.If the back clearance of a piston ring is excessive, __________.
- 1603.Starting a large low-speed propulsion diesel engine on diesel fuel during cold weather conditions, will be made easier by __________.
- 1604.Leaking oil seals on a diesel engine turbocharger can cause __________.
- 1605.Burning fuel with a high sulfur content in a diesel engine will __________.
- 1606.In certain cases, a cylinder liner can be refinished rather than replaced. When properly honed, the __________.
- 1607.Jacket water heaters are used on diesel engines to __________.
- 1608.Which of the following problems may occur when using fuel oil with a high sulphur content?
- 1609.A properly honed diesel engine cylinder liner will __________.
- 1610.The consistent burning of fuel oil with a high sulfur content in a diesel engine will result in __________.
- 1611.The burning of fuel oil in a diesel engine having a high sodium content, will cause __________.
- 1612.Which of the following statements concerning cylinder liner wear in a single acting diesel engine is correct?
- 1613.Diesel engine starting difficulties due to cold intake air temperatures, can be overcome by using a/an __________.
- 1614.A turbocharged and after cooled diesel engine can over speed due to __________.
- 1615.The cetane number rates fuels for diesel engines according to its __________.
- 1616.Generally, where should you expect to find the greatest amount of wear on a cylinder liner?
- 1617.In diesel engineering practice, the term used to express the ignition quality of a particular fuel is __________.
- 1618.The rate of wear on a cylinder liner depends on the __________.
- 1619.When starting a diesel engine at temperatures below 70°F, the frictional resistance to turning will be __________.
- 1620.Which of the following conditions may be attributed to a fouled turbocharger compressor inlet screen or filter?
- 1621.A scored diesel engine cylinder liner will cause __________.
- 1622.Cold weather starting of a diesel engine is more difficult than warm weather starting due to __________.
- 1623.Why will a turbocharged diesel engine produce black smoke if excessive additional load is applied too quickly?
- 1624.Which of the listed factors will indicate the most about the ability of a fuel to ignite in a diesel engine?
- 1625.Starting aids, such as glow plugs, are usually installed on __________.
- 1626.The cetane number of a diesel fuel oil indicates its __________.
- 1627.Air motors used for starting some auxiliary diesel engines are generally the type known as a/an __________.
- 1628.The cetane rating of diesel fuel is an indication of the __________.
- 1629.Which of the following conditions could contribute to the cracking of a diesel engine cylinder head?
- 1630.Fluid type starting motors used for starting auxiliary diesel engines may either be of the piston type or the __________.
- 1631.The ignition quality of diesel fuel oil is indicated by the __________.
- 1632.To measure bearing clearances, a special small diameter plastic rod (plasti-gage) is placed between the crankshaft journal and the connecting rod bearing shell. The actual reading is obtained by __________.
- 1633.The ignition quality of a diesel fuel is indicated by the __________.
- 1634.To determine the main bearing clearance of a propulsion diesel engine, you should measure the main bearing shell using a ball anvil outside micrometer and measure the crankshaft journal using a/an __________.
- 1635.Which internal combustion engine starting system uses a vane type fluid motor?
- 1636.Which of the following represents the significance the fuel oil cetane number?
- 1637.On a large low-speed main propulsion diesel engine, lower main bearing wear is usually measured by using a/an __________.
- 1638.An air starting motor for a diesel engine is protected from over speeding by __________.
- 1639.The ignition quality of a fuel oil is an important operational consideration because it __________.
- 1640.Which of the devices is commonly used in measuring the clearances between the main engine bearings and the crankshaft?
- 1641.In addition to the main starting air compressor, another air compressor, driven by a separate power source, is installed to __________.
- 1642.Fuel oil having a low cetane rating could result in __________.
- 1643.To determine the main bearing clearances in a small auxiliary diesel engine, you should use __________.
- 1644.The starting air supply for a diesel engine is generally produced by a/an __________.
- 1645.Which of the following statements is true concerning the cetane number of diesel fuel?
- 1646.Where is the air charge for an air starting system stored?
- 1647.Which of the following statements is true concerning the cetane number rating of diesel fuel?
- 1648.The insertion of shims between the foot of a marine type connecting rod and a bearing box would result in __________.
- 1649.Intercoolers installed on starting air compressors, reduce the possibility of __________.
- 1650.Which of the following operating conditions will occur when shims are removed from the joint between the foot of a marine type diesel engine connecting rod and the bearing box?
- 1651.A two-stroke/cycle diesel engine requires less starting air than a four-stroke/cycle diesel engine, of equal displacement, because the two-stroke/cycle diesel engine __________.
- 1652.With respect to diesel fuel, the ease with which a cold engine will start is dependent upon the __________.
- 1653.Worn main bearings will cause the compression ratio of a diesel engine to __________.
- 1654.Starting systems for large, direct reversing, main propulsion diesel engines are usually __________.
- 1655.A mixture of 45% cetane and 55% alpha-methyl-naphthalene is found to have the same ignition delay as a sample of diesel oil. The sample can be described as having a/an __________.
- 1656.In a large, low-speed diesel engine the clearance between the piston crown and cylinder head is found to be excessive. In order to correct for this, you should __________.
- 1657.Which of the listed types of starting systems is often used on large, low-speed, direct reversing, main propulsion diesel engines?
- 1658.An acceptable method for measuring the applied rotational force when tightening connecting rod and main bearing bolts, is to use a __________.
- 1659.Which of the following relationships exist between the temperature developed in a combustion space, and the compression ratio of the engine?
- 1660.Injection lag in a diesel engine may be caused by __________.
- 1661.Abnormal crankpin bearing and piston skirt surface wear indicate __________.
- 1662.Diesel engine injection lag is caused by __________.
- 1663.The pilot valves in an air pilot starting system for a two-stroke/cycle, direct-reversing, main propulsion diesel engine are operated by either a ported distributor disc or a/an __________.
- 1664.Fuel oil injected into the cylinder of a diesel engine just after the piston passes top dead center, will __________.
- 1665.Diesel engine crankshaft deflection readings are generally taken at four crank positions. Good engineering practice requires the deflection gage or indicator to be __________.
- 1666.Heat for igniting the fuel oil in the cylinder of a diesel engine is generated by the __________.
- 1667.One method of determining crankshaft misalignment is by __________.
- 1668.Cams used to activate mechanically operated air starting valves on four-stroke/cycle diesel engines should have which of the valve lift profiles listed?
- 1669.The timing of diesel engine air starting valves is controlled by __________.
- 1670.Diesel engine air start valve timing is controlled by __________.
- 1671.In the cylinder of a diesel engine, fuel is ignited by the __________.
- 1672.If there is a 'clicking' sound in the valve compartment of a diesel engine, the cause may be __________.
- 1673.A loud clicking noise from the valve compartment of an operating diesel engine would indicate __________.
- 1674.Excessively worn, or polished ends on a diesel engine valve spring, indicate __________.
- 1675.When a hydraulic valve lifter is on the base circle of the cam, 'zero' valve lash is maintained by the __________.
- 1676.Fuel oil day tanks for diesel engines must be checked and cleaned at regular intervals in order to remove __________.
- 1677.Small cracks in the crankshaft bearing surface of a diesel engine are an indication of __________.
- 1678.Which of the following methods is used to prevent throttling of compressed air through the diesel engine air starting valves?
- 1679.The depth of fuel oil in a tank is normally measured through the __________.
- 1680.An eight cylinder, four stroke/cycle, single acting diesel engine has a 650 mm bore and a 1400 mm stroke. What will be the developed indicated metric horsepower if the average mean effective pressure is 30 kg/cm2 at a speed of 100 RPM?
- 1681.Starting air check valves are held firmly on their seats by __________.
- 1682.Fuel oil is regularly transferred to the day tank in order to __________.
- 1683.Following an overhaul of a crosshead type diesel engine, the engine is jacked over with the turning gear as part of the pre-start procedure. Which of the listed pre-start procedures should be carried out?
- 1684.If water is found in the crankcase of a diesel engine, the cause may be due to __________.
- 1685.A six-cylinder, four-stroke/cycle diesel engine is fitted with a rotary distributor type air starting system. The speed of the rotating distributor disc is __________.
- 1686.Standby, or emergency diesel generator day tanks should always be kept full to reduce the possibility of __________.
- 1687.How can water enter the crankcase of an operating diesel engine?
- 1688.An accumulator used in a hydraulic starting system is generally located between the __________.
- 1689.The device used to store a charged pressure for an hydraulic starting system is called the __________.
- 1690.Which of the listed contaminants will be satisfactorily removed from fuel oil by centrifuging?
- 1691.Water accumulating in the crankcase of a diesel engine could indicate __________.
- 1692.One engine manufacturer recommends heavy fuel oil should not be heated above 80°C to 95°C (176°F to 203°F) before purification. This upper limit should be observed to ensure against __________.
- 1693.Excessive valve clearance will cause a valve to open __________.
- 1694.In a hydraulic starting system, oil to the starting motor flows from the __________.
- 1695.On board supply vessels, a centrifuge is normally used to purify __________.
- 1696.The most effective method in removing water from diesel fuel oil is by __________.
- 1697.In a four-stroke/cycle diesel engine, piston blow-by can result in increased __________.
- 1698.Diesel engine piston ring blow-by is usually caused by excessive ring clearance at the ring __________.
- 1699.During diesel engine warm-up, which type of valve lash adjuster compensates for the change in length of the exhaust valve stem?
- 1700.Hydraulic starters are installed on many lifeboat diesel engines instead of comparable air start systems, because __________.