USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 14
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1301.Oil oxidation as a result of excessively high lube oil temperature, is harmful to a diesel engine because __________.
- 1302.Two important considerations to maintain proper lubrication of a diesel engine include the delivery of oil in sufficient amount along with an acceptable __________.
- 1303.Excessive mechanical and pulsating vibrations developed in a main propulsion diesel engine may be more likely to cause damage to an attached __________.
- 1304.Sludge formation in a diesel engine lube oil system is caused by __________.
- 1305.Before starting a diesel engine, you should always __________.
- 1306.If the low level alarm of the diesel fuel day tank fails to function, you can expect trouble from __________.
- 1307.Proper lubrication of the main bearings is more easily obtained in a single acting, four-stroke/cycle diesel engine than in a two-stroke/cycle diesel engine because __________.
- 1308.An after cooler installed between the turbocharger and the cylinder air inlet __________.
- 1309.Which instrument is used to take crankshaft deflection readings?
- 1310.One cause of diesel engine surging can be a result of __________.
- 1311.The purpose of an intercooler installed on a high pressure starting air compressor is to ___________.
- 1312.Fuel combustion in a diesel engine cylinder should begin just before the piston reaches top dead center and should __________.
- 1313.The longer ignition delay period resulting from the use of low cetane fuel, will result in ____________.
- 1314.Which of the following should always be checked prior to starting a diesel engine?
- 1315.Air is normally bled from a diesel engine fuel system by __________.
- 1316.If cooling water flow through the after cooler is interrupted, the power output of a turbocharged diesel engine will drop because the __________.
- 1317.Wear is usually greatest at the top of the cylinder bore of a diesel engine due to the __________.
- 1318.Which of the following conditions will cause the greatest increase to the wear rate in a cylinder liner?
- 1319.An acceptable means of tightening connecting rod and main bearing cap bolts is to measure the __________. I. torque applied to each nut and bolt assembly II. stretch of each bolt after tightening
- 1320.After an engine has been started using a Bendix drive unit, the drive pinion disengages from the flywheel due to __________.
- 1321.Cooling water pumps driven by direct reversing diesel engines are usually of the straight impeller vane type pump with a concentric housing to __________.
- 1322.Prior to starting most medium-speed propulsion diesel engines, which of the procedures listed should be observed?
- 1323.If you determine that entrained air in the fuel oil system is causing a diesel engine to stall, you should first check for __________.
- 1324.Which of the following procedures should be carried out to permit the continued operation of a crosshead engine with a leaky after cooler?
- 1325.Telescopic pipes which are attached to water cooled pistons of large slow-speed main propulsion diesel engines are designed to __________.
- 1326.In a diesel engine lube oil system, which of the following components should be lubricated first?
- 1327.Immediately after starting a diesel engine, you should first check and monitor the __________.
- 1328.Before shutting off the fuel supply to stop and secure a diesel engine, why is it necessary to allow the engine to idle for a few minutes?
- 1329.In the starting process of a diesel engine, the main object is to attain the compression conditions sufficient to __________.
- 1330.Which of the listed devices is often used in combination with the flywheel of small and medium size diesel engines for the purpose of starting?
- 1331.The minimum delivery pressure required for diesel engine fuel oil injection depends primarily on the __________.
- 1332.An increase in the load on a turbocharged diesel engine operating at constant speed will result in an increase in __________.
- 1333.Low compression pressure in a diesel engine cylinder can be caused by __________.
- 1334.Piston area, multiplied by piston stroke, multiplied by number of cylinders, equals engine __________.
- 1335.Lube oil pumps taking suction from the sumps of marine diesel engines are usually classified as __________.
- 1336.In a unit injector, an upper helix and lower helix are machined in the lower part of the plunger for __________.
- 1337.When attempting to restart a warm high-speed engine, which of the following reactions can you expect?
- 1338.The amount of fuel delivered by a helical plunger fuel injection pump is controlled by __________.
- 1339.The high air velocity leaving the air impeller of an exhaust gas turbocharger is converted to pressure in the __________.
- 1340.In a jerk pump, the amount of fuel that will be forced through the spray nozzle on each upward stroke of the plunger depends on __________.
- 1341.Load control on a diesel engine is accomplished by __________.
- 1342.Movement of the pump control rack in a fuel injection system using individual plunger-type pumps __________.
- 1343.The amount of fuel delivered by a unit injector is controlled by the __________.
- 1344.The effective pump stroke of an individual port-and-helix fuel injection pump is determined by the __________.
- 1345.Your vessel is about to begin maneuvering, in order to carry out easy restarting of a large heavy fuel diesel engine that has been stopped for some time, you should have __________.
- 1346.Which of the following conditions would cause carbon deposits to form in the piston ring belt of a diesel engine?
- 1347.Air in the fuel lines to the fuel injection nozzles of a diesel engine will result in __________.
- 1348.The amount of fuel delivered by a helical plunger type fuel injection pump is controlled by __________.
- 1349.The amount of fuel injected into a diesel engine cylinder by a unit injector, is controlled by __________.
- 1350.Fuel oil penetration into the cylinder of a diesel engine is __________.
- 1351.Injection pressure in a common rail fuel system is controlled by __________.
- 1352.Which of the following operating procedures should be carried out immediately after any diesel engine is started?
- 1353.Air in the fuel can cause __________.
- 1354.Increasing the compression ratio of a diesel engine while maintaining the designed rate of fuel flow will result in __________.
- 1355.How many separate camshaft timing events must be controlled for the components of an air start cylinder head for a direct reversible, four stroke diesel engine?
- 1356.To facilitate early ring seating of newly installed piston rings, while still providing extended ring wear, __________.
- 1357.During diesel engine warm-up, which type of valve lash adjuster automatically compensates for the thermal expansion of the exhaust valve stem?
- 1358.In comparison to exhaust valves, intake valves of diesel engines may be fabricated from low-alloy steels because __________.
- 1359.The greatest turbulence in a diesel engine cylinder is created by the __________.
- 1360.If a diesel engine starts firing, but is unable to come up to normal speed, the cause may be __________.
- 1361.After changing out the fuel filters the diesel engine fails to restart. The most probable cause for this condition is a/an __________.
- 1362.When the load is increased on a turbocharged diesel engine, the amount of increased air supplied by the turbocharger will __________.
- 1363.Which of the following operations will have a direct impact on the rate of wear in a cylinder liner __________.
- 1364.A spring-loaded centrifugal flyweight governor responds to reduced engine load with an immediate increase in __________.
- 1365.To routinely clean a metal-edge type lube oil strainer, you should __________.
- 1366.A 'Blotter test' is a test performed on the lube oil of a diesel engine which can determine __________.
- 1367.After starting a diesel engine, which of the listed operating conditions should be checked FIRST?
- 1368.Faulty operation of diesel engine fuel injection nozzles can be a direct cause of __________.
- 1369.Which of the following test indicators should be considered the most significant factor in determining as to whether or not a diesel generator's lube oil should be drained and renewed?
- 1370.In a turbocharger, inlet air velocity is increased in the __________.
- 1371.The pinion of an auxiliary diesel electric starting motor normally engages the flywheel ring gear by means of a/an __________.
- 1372.In a large slow-speed propulsion diesel engine, the side thrust on the crosshead is the direct result of _____.
- 1373.In a naturally aspirated diesel engine, the volumetric efficiency of the intake air charge is mainly influenced by the __________.
- 1374.Why do most temperature control valves in diesel engine closed freshwater cooling systems bypass the flow of jacket water around the cooler instead of around the engine?
- 1375.While underway, which of the following would be the FIRST step in reversing a direct reversing large, low-speed, main propulsion, diesel engine?
- 1376.Dirt in a fuel oil system of a diesel engine can cause __________.
- 1377.Effective operation of a hydraulic coupling depends upon a specified amount of __________.
- 1378.The power developed by a large slow-speed main propulsion diesel engine is dependent upon the __________.
- 1379.In a diesel engine lube oil system, which of the following parts should be lubricated first?
- 1380.Which of the factors listed has the greatest effect on the mechanical efficiency of a diesel engine?
- 1381.The cooling water pump driven by a direct reversing diesel engine is usually of the straight impeller vane type with a concentric housing to ____________.
- 1382.Which of the following conditions would require the removal of a turbocharger for repair?
- 1383.During maneuvering operations for a direct reversing large, low-speed, main propulsion diesel engine, which of the following actions is used to stop the shaft from turning prior to changing the engine rotation for a vessel with moderate headway?
- 1384.The most common diesel engine fuel system problems are caused by __________.
- 1385.Exhaust gas pyrometers are useful for __________.
- 1386.When a generator diesel engine is operated at partial load, as compared to full load, a decrease will occur in the average __________.
- 1387.The direct cause of a crankcase explosion can be attributed to __________.
- 1388.In using reduction gears to obtain efficient propeller speeds, __________.
- 1389.Maximum rated horsepower of a diesel engine is attained __________.
- 1390.Diesel engine fuel oil contamination often results in __________.
- 1391.What condition listed below would specifically indicate that a pump overhaul was necessary for a centrifugal saltwater service pump.
- 1392.Wet-type exhaust silencers, used with some lifeboat diesel engines, utilize which design feature?
- 1393.The interior of some diesel engine saltwater heat exchangers are protected from electrolytic corrosion by the use of __________.
- 1394.What is the crank angle between cylinder firing of a four-stroke/cycle, in line, eight cylinder diesel engine?
- 1395.In a diesel engine fuel oil jerk pump, the amount of fuel that will be forced through the spray nozzle on each upward stroke of the plunger depends upon ____________.
- 1396.A diesel engine should not be operated at low loads for long periods of time because __________.
- 1397.The major cause of fuel pump and injection system problems is __________.
- 1398.To manually bypass a strainer or filter in a shunt type lube oil filtering system, __________.
- 1399.Combustion knock occurring in a diesel engine can be caused by __________.
- 1400.The ability of the governor to prevent fluctuations in engine speed is termed __________.