USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 3
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 201.Excessive return oil pressure from a variable capacity return flow fuel oil burner system on an automatic auxiliary boiler, will cause __________.
- 202.The concentration of total dissolved solids in the water of an auxiliary boiler can increase as a result of __________.
- 203.The camshaft drive is designed to maintain proper camshaft speed relative to crankshaft speed. In maintaining this relationship, the camshaft drive causes the camshaft to rotate at __________.
- 204.Wristpin bearings are difficult to lubricate because of their oscillating motion and __________.
- 205.A three-way thermostatic control valve regulates the diesel engine cooling water temperature by passing a portion of the water __________.
- 206.Automatic burner shutdown in an auxiliary boiler, as a result of a component failure in the flame safeguard controls, will __________.
- 207.When an auxiliary boiler is secured and you expect to relight the unit within six hours, you should __________.
- 208.If the combustion control system of an automatically fired auxiliary boiler fails to restart from the normal shutdown mode, you should check for __________.
- 209.Bottom blow valves are installed on auxiliary water-tube boilers to __________.
- 210.A sprayer plate marked 32Y20, as used in a return flow fuel oil system, should only be used with a/an __________.
- 211.Mechanical lubricators for diesel engine cylinders are usually small reciprocating pumps which are __________.
- 212.In a diesel engine closed freshwater cooling system, the amount of engine coolant flowing through the heat exchanger is controlled by the __________.
- 213.Which of the following conditions is indicated by the presence of water in the scavenging air receiver?
- 214.Crankcase explosion relief valves should be of the __________.
- 215.Which of the following conditions is NOT an indication of microbial contamination of the fuel supply?
- 216.The opening of an exhaust valve on a modern, large, low-speed, main propulsion diesel engine, may be actuated by __________.
- 217.The speed of the camshaft in a two-stroke/cycle diesel engine, running at 950 RPM, is __________.
- 218.Cylinder lubrication oil for low speed main propulsion diesel engines is admitted to each cylinder during __________.
- 219.Temperature control valves installed in the jacket cooling water system of a diesel engine, modulates the rate of water flow through the __________.
- 220.In comparison to straight flow mechanical atomizers, return flow atomizers provide relatively uniform atomization over a wide firing range due to the __________.
- 221.A restricted air intake to a diesel engine may result in the engine __________.
- 222.Explosion relief valves on diesel engine crankcases should relieve the pressure at not more than __________.
- 223.Which of the following conditions is NOT an indication of microbial contamination?
- 224.In a four-stroke/cycle diesel engine, the camshaft rotates at __________.
- 225.What is the purpose of the 'window' installed in the housing of an individual jerk pump?
- 226.For diesel engine piston cooling, lubricating oil can be supplied to the pistons by a/an __________.
- 227.The jacket water temperature in a diesel engine closed freshwater cooling system is normally controlled by __________.
- 228.Variations in the amount of fuel oil burned in a return flow type burner of an auxiliary boiler, are controlled by the __________.
- 229.On a turbocharged, medium-speed, diesel engine, which of the following problems is an indication of a restricted air intake passage?
- 230.The water in an operating auxiliary boiler should be tested for alkalinity and chloride content each __________.
- 231.Coast Guard Regulations (46 CFR) require that the flame safeguard control system for an automatic boiler, should __________.
- 232.The closing of the exhaust valves used on a modern, large, low-speed, main propulsion diesel engine may be directly provided by __________.
- 233.In a two-stroke/cycle diesel engine, the camshaft rotates at __________.
- 234.Why do most temperature control valves in diesel engine closed freshwater cooling systems vary the flow of jacket water through the cooler instead of through the engine?
- 235.An important design characteristic of an explosion relief valve for a diesel engine is the ability to __________.
- 236.Which of the following statements describes how the fuel oil enters the whirling chambers of the sprayer plates used in a auxiliary boiler return flow fuel oil system?
- 237.If a four-stroke/cycle diesel engine is running at 1550 RPM, the speed of the camshaft will be __________.
- 238.Shaker, circulation, and spray are the three general methods used in __________.
- 239.For proper operation, auxiliary boiler feed water must have which of the following characteristics?
- 240.The most common cause of scale formation in an auxiliary boiler is __________.
- 241.If over a period of weeks the air-box pressure of a turbocharged, diesel engine, operating at full load, appears to be dropping off, the cause can be __________.
- 242.Before an auxiliary boiler is shutdown for an extended period of time, the water in the boiler should have a pH value of __________.
- 243.Which of the following statements concerning the alarms for automatically controlled auxiliary boilers complies with applicable Coast Guard Regulations (46 CFR)?
- 244.The purpose of the delivery check valve used in a diesel fuel injection jerk pump is to __________.
- 245.The method of piston cooling in which oil is delivered through the connecting rod to a compartment within the piston, then distributed by the motion of the pistons, and allowed to drain to the crankcase via one or more holes or pipes, is termed __________.
- 246.What would be considered a normal temperature increase between the inlet and outlet jacket cooling water of a medium or high-speed diesel engine operating at normal load?
- 247.Which statement regarding the arrangement and location of explosion relief valves used on an internal combustion engines is true?
- 248.Proper housekeeping to prevent the formation of microbiological growths within a fuel system includes the prevention of water accumulations and the use of __________.
- 249.Excessive alkalinity of the water in an auxiliary boiler can cause __________.
- 250.Two solenoid control valves are required on large automatic auxiliary boilers, and will simultaneously shut off the fuel in the event of __________.
- 251.The procedures recommended for auxiliary boilers having high salinity include __________.
- 252.The solenoid valves in the fuel oil supply line to an automatically fired auxiliary boiler, are automatically closed by __________.
- 253.Which operating parameter may need to be decreased when running a large main propulsion diesel engine at low load conditions?
- 254.In the event of a flame failure in an auxiliary water-tube boiler, you must __________.
- 255.If the intake, or exhaust valve stem clearance is found to be excessive, in addition to too little movement of the rocker arms, you should check for __________.
- 256.Improper maintenance of the fuel oil burners in an automatically fired auxiliary boiler, could result in __________.
- 257.The concentration of dissolved solids in the boiler water of an auxiliary boiler could increase as a result of __________.
- 258.Failure of the feed pump to deliver feed water to an auxiliary boiler could be caused by __________.
- 259.Why should the main steam stop valve of an auxiliary boiler be eased off its seat and then gently closed before lighting off?
- 260.One function of the fuel pump delivery check valve is to __________.
- 261.For any piston ring to operate smoothly without scuffing, the ring must be __________.
- 262.Using a cooling water temperature of 225°F (107.2°C), instead of 180°F (82.2°C) in an auxiliary diesel engine, will __________.
- 263.Flame failure in an automatically fired auxiliary boiler can result from a/an __________.
- 264.How many crankcase relief valves are required for a 13 inch bore, eight cylinder in-line engine?
- 265.If the fuel/air ratio in an automatically fired auxiliary boiler is insufficient, the result could lead to __________.
- 266.Which of the following actions should normally be taken during each watch when the auxiliary boiler is in operation?
- 267.Under which of the following conditions must the combustion control system for a small automatic auxiliary boiler secure the burner?
- 268.The primary function of a fuel delivery check valve assembly is to __________.
- 269.The upper piston rings in large, slow-speed, two-stroke/ cycle diesel engines are most effectively lubricated by oil __________.
- 270.Operating a diesel engine for prolonged periods at temperatures lower than the normal design temperature may cause __________.
- 271.A pulsating flame, accompanied by a burner developing black smoke in an auxiliary boiler, is an indication that the __________.
- 272.Which of the following actions should normally be taken during each watch when the auxiliary boiler is in operation?
- 273.Flame failure in an operating automatically fired auxiliary boiler can result from a __________.
- 274.A failure of any component of a flame safeguard control for an auxiliary boiler will result in __________.
- 275.The daily inspection of an operating auxiliary boiler should include __________.
- 276.Where is the fuel delivery check valve located in a jerk pump fuel injection system?
- 277.As a general rule, the recommended operating water jacket outlet temperature range for medium and high speed marine diesels with closed cooling systems is __________.
- 278.If a tube ruptures in a water-tube auxiliary boiler due to low water, you should __________.
- 279.An automatically fired auxiliary boiler with carbon deposits formed on its burner electrodes, will experience __________.
- 280.An exhaust gas bypass is installed on a waste heat boiler in order to __________.
- 281.The delivery valve installed in a port and helix fuel injection pump is designed to __________.
- 282.The fuel oil supply system to an automatic auxiliary boiler, will automatically shutdown if the boiler __________.
- 283.A closed freshwater cooling system is commonly used with marine diesel engines because the __________.
- 284.The diesel engine exhaust gas bypass, as fitted with some waste heat boilers, is installed to __________.
- 285.Loop,' 'uniflow,' 'cross flow,' and 'return-flow' are terms used to describe various types of __________.
- 286.Oxygen corrosion in auxiliary boilers is prevented by treating the boiler feed tank with __________.
- 287.Coast Guard Regulations (46 CFR) require the "trial for ignition period" on boilers must not exceed __________.
- 288.A bypass line provided around a waste heat auxiliary boiler in a diesel engine exhaust system, may be used to avoid boiler __________.
- 289.Which of the listed sequence of events occurs when an automatic auxiliary boiler is pre-purged?
- 290.High stack temperature occurring in an auxiliary boiler could be a result of __________.
- 291.A firebox explosion in an automatically fired auxiliary boiler may be the result of __________.
- 292.The principal difference between loop scavenging and cross flow scavenging, as used in single acting diesel engines, is the __________.
- 293.An inline engine having a nine inch bore and more than eight cylinders will __________.
- 294.The PRIMARY function of a waste heat boiler is to __________.
- 295.Fuel droplets injected into a diesel engine cylinder must have adequate penetration to __________.
- 296.A coil-type automatically fired auxiliary boiler is to be laid up wet for an indefinite period. The boiler water should be treated to ensure that __________.
- 297.Coast Guard Regulations (46 CFR) require all automatically fired low pressure heating boilers to have an automatic __________.
- 298.Collapsed hydraulic valve lifters in a diesel engine will result in __________.
- 299.Large, two-stroke/cycle, main propulsion, diesel engine cylinders can be successfully pressure charged during normal operation, by using the __________.
- 300.Control of the fuel oil metering valve in an automatically fired auxiliary boiler is accomplished by a __________.