USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 15
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1401.A 16 cylinder main propulsion diesel engine is operating at 95% of full load. No. 7 cylinder is in alarm condition and indicating 1000°F exhaust temperature. All fuel racks are at 21-22 mm except No. 7 which is at 18mm. A new fuel injector nozzle for No. 7 cylinder had been recently installed. Which of the listed actions should be carried out NEXT?
- 1402.To guarantee that a reduction gear bearing is receiving proper oil supply, you should check the __________.
- 1403.What changes in valve timing will tend to increase the cooling effect on the exhaust valve in a four-stroke cycle turbocharged diesel engine?
- 1404.A diesel engine operating at a light load, when compared to operating at heavy load has an air/fuel ratio that is __________.
- 1405.A dirty fuel oil filter element can be detected by __________.
- 1406.Which factor determines the size of the ring dam for a fuel oil centrifugal purifier?
- 1407.Cylinder scavenging in a turbocharged, four-stroke/cycle, single acting, diesel engine is accomplished __________.
- 1408.A four-stroke cycle main propulsion diesel engine fails to start at normal cranking speed with normal fuel pressure and ambient temperature. The reason for the failure could be __________.
- 1409.For equal amounts of fuel injected, what change in condition will have the greatest effect on the mean effective pressure in the cylinder of a diesel engine?
- 1410.What type of marine engine has a fuel nozzle and combustion chamber located between two pistons in a common cylinder liner?
- 1411.The ignition quality of diesel fuel becomes LESS critical as __________.
- 1412.When calculating the indicated power developed in a diesel engine cylinder, 1 horsepower is equivalent to "33,000 foot-pounds per minute". What conversion factor would be used if the values are based on metric "kilogram-meters per minute"?
- 1413.Operating a low speed propulsion diesel engine at less than 30% of designed normal load for prolonged periods will result in __________.
- 1414.The main source of fuel pump and injection system malfunctions is __________.
- 1415.What contaminants found in engine lube oil will cause an increase in wear rate of metal components in a diesel engine.
- 1416.Turbocharged four-stroke/cycle diesel engines utilize valve overlap for __________.
- 1417.In a four-stroke/cycle medium-speed diesel engine, fuel injection commences at 10 crankshaft degrees before top dead center. After fuel injection commences, approximately how many degrees will the camshaft rotate before the exhaust valve begins to open?
- 1418.What type of main bearings are commonly used on crankshafts for most propulsion diesel engines?
- 1419.Which of the following conditions may be responsible for allowing lube oil to contaminate the jacket water cooling system of an auxiliary diesel engine?
- 1420.What harmful condition can result if a diesel engine is operated at very light loads for long periods of time?
- 1421.A faulty injector in one cylinder of an operating diesel engine can be located by __________.
- 1422.Early injection timing is indicated by __________.
- 1423.In a turbocharged four-stroke/cycle diesel engine, the exhaust valve remains open until after top dead center and the intake valve opens before top dead center to __________.
- 1424.Which of the following ring designs is commonly used on new piston rings to facilitate run-in or seating?
- 1425.When a nozzle tester is used to check the spray pattern of a diesel fuel injection nozzle, which of the following statements is true?
- 1426.A 'Blotter Test' can be performed on a 'used' lube oil sample of a diesel engine to determine _____________.
- 1427.Operating a diesel engine under light loads and at low temperatures for an extended period can result in __________.
- 1428.Incorrect timing of the fuel injection system is similar to the effects of poor __________.
- 1429.When installing new rings during a engine piston overhaul, the piston ring gap should first be measured with feeler gages by __________.
- 1430.Which of the listed design features is most common with a two-stroke cycle, low-speed main propulsion diesel engine?
- 1431.The ignition quality of diesel fuel is indicated by its __________.
- 1432.While maneuvering, you discover heavy smoke coming from the turbocharger casing, you should __________.
- 1433.A change in the quality of fuel atomization by a diesel engine fuel injector would be caused by a/an __________.
- 1434.A turbocharged, four-stroke/cycle diesel engine has a larger valve overlap than a naturally aspirated four-stroke/cycle diesel engine, in order to increase the __________.
- 1435.A diesel engine cylinder has a swept volume of 135 cubic inches and a clearance volume of 10 cubic inches at top dead center. What is the compression ratio of the engine cylinder?
- 1436.A diesel engine cylinder has a swept volume of 125 cubic inches and a clearance volume of 10 cubic inches at top dead center. What is the compression ratio of the engine cylinder?
- 1437.A diesel engine cylinder has a swept volume of 125 cubic inches and a compression ratio of 13.5 to 1. What is the clearance volume in the cylinder at top dead center?
- 1438.Lube oil contamination will increase due to normal wear of engine components as a result of _____________.
- 1439.The rate of pressure rise in a diesel engine cylinder following fuel injection and ignition, is mainly influenced by the ___________.
- 1440.In extremely cold weather, an engine turns over too slowly and fails to start. This problem is most likely the result of __________.
- 1441.When fuel enters the crankcase of a diesel engine, it __________.
- 1442.Friction, engine wear, and oil consumption in a diesel engine can be directly attributed to the __________.
- 1443.The exhaust ports of a diesel engine using the cross flow scavenging method are opened and closed by the __________.
- 1444.Which chemical is most often utilized to prevent and correct most microbial contamination occurring within fuel storage systems?
- 1445.Carbon deposit build up on the injection nozzle orifice is least likely to occur when using which type of fuel injector nozzle?
- 1446.An immediate repair is required if a leak occurs in the high pressure fuel piping between the injection pump and fuel nozzle because of the __________.
- 1447.The pressure in an operating diesel engine cylinder continues to rise for a short period after the piston passes top dead center as a result of the __________.
- 1448.Which precaution must be taken when securing a diesel engine if an electric jacket water heater is installed in the engine block?
- 1449.A large, low-speed, main propulsion diesel engine is operating at 80% load and normal speed while the vessel is in calm seas. As the intensity of the seas increase, the engine speed governor maintains the same RPM, although the load indicator indicates an increase in load beyond its allowable limits. Which of the following actions should be taken?
- 1450.A change in the degree of fuel atomization in a diesel engine greatly affects the __________.
- 1451.In a Roots-type rotary blower, the volume of air delivered is directly proportional to __________.
- 1452.Electric starting motors for diesel engines require high current for their operation. As a result of this, they __________.
- 1453.A safety crankcase cover differs from other diesel engine access doors in that it is fitted with a __________.
- 1454.The 'breaking-up' of fuel as it enters a diesel engine cylinder is known as __________.
- 1455.On a diesel engine equipped with a Roots-type blower, __________.
- 1456.Which characteristic of the theoretical Otto cycle does not occur in the theoretical Diesel cycle?
- 1457.The control rack to a unit injector regulates fuel delivery by __________.
- 1458.Insufficient end clearance on newly fitted piston rings in a diesel engine will cause the rings to __________.
- 1459.If a two-stroke/cycle diesel engine is over speeding due to leakage of lube oil into the cylinders, what should you do to stop the engine?
- 1460.Which of the following statements concerning fuel atomization in a diesel engine cylinder is correct?
- 1461.To facilitate early ring seating of newly installed piston rings, while still providing extended ring wear, __________.
- 1462.If a single cylinder relief valve on a main propulsion diesel engine begins to lift, but it is not possible to secure the engine, which of the following actions should be taken?
- 1463.If the firing pressures in a diesel engine are high, although the exhaust temperatures are normal, the cause may be __________.
- 1464.Injection lag in a diesel engine may be caused by __________.
- 1465.Clogged diesel engine fuel oil filters can cause __________,
- 1466.Which of the following conditions would result in the necessity for an increased frequency of oil and oil filter changes for an auxiliary diesel engine.
- 1467.If an small auxiliary diesel engine will not crank but is able to be barred over, the trouble may be __________.
- 1468.An efficient seal between the cylinder block and cylinder heads on many auxiliary diesel engines is obtained with __________.
- 1469.Before shutting off the fuel supply to stop a medium or high-speed diesel engine, why is it necessary to allow the engine to idle for a few minutes?
- 1470.Diesel engine injection lag is caused by __________.
- 1471.An auxiliary diesel generator continues to run after you try to shut down. Your next course of action should be to _____________.
- 1472.A Roots-type blower installed on some diesel engines, serves to __________.
- 1473.Which of the following problems can occur if accumulating condensate is not drained off from a starting air receiver?
- 1474.The most crucial time for any bearing with regards to diesel engine lubrication is __________.
- 1475.Which of the bearing types listed is most commonly used for their ability to absorb thrust in reduction gear applications?
- 1476.Turbulence is created in the cylinders of a diesel engine to __________.
- 1477.A normally operating diesel engine is shutdown by __________.
- 1478.According to 46 CFR Part 56, isolation valves used in keel cooler installations may be constructed of __________.
- 1479.Compared to a naturally aspirated diesel engine, a supercharged diesel engine has __________.
- 1480.The compression of air in a positive displacement rotary supercharging blower, occurs only __________.
- 1481.When would the available energy of the exhaust gases of a two-stroke/cycle diesel engine driving a turbocharger, result in a low value of scavenging air pressure for combustion?
- 1482.The possibility of a diesel engine crankcase explosion will be increased by operating an engine __________.
- 1483.When running a large, dual fuel, main propulsion diesel engine on heavy fuel, which of the following precautions should be observed when switching from heavy fuel oil to diesel oil?
- 1484.In an operating diesel engine, which of the following is true concerning a tube and shell type jacket water heat exchanger?
- 1485.The loss of the diesel engine cylinder air charge through leaky valves, piston rings, worn or scored liners, would be indicated by which of the following sets of conditions?
- 1486.If a small auxiliary diesel engine will not crank but can be barred over, the trouble may be due to __________.
- 1487.In comparison to exhaust valves, intake valves of diesel engines may be fabricated from low-alloy mild steels because __________.
- 1488.In a diesel engine closed freshwater cooling system, the cooling water pressure drop through the engine is 10 psig, and the pressure drop through the heat exchanger is 4 psig at maximum flow rates. The cooling water pump must produce a discharge head of at least __________.
- 1489.Which of the listed governor characteristics will determine the final load sharing relationship between paralleled diesel generators?
- 1490.Integral cylinder liners constructed as part of the cylinder block, are characterized by which of the following disadvantages?
- 1491.For most auxiliary diesel generator engines, the over speed trip device will stop the engine by __________.
- 1492.How many separate initial timing events must be controlled in the cylinder head of a direct admission air start, direct reversible, four stroke diesel engine?
- 1493.Grey smoke exhausting from a running diesel engine can be caused by __________.
- 1494.Which of the following statements represents the proper order of thrust transmission when a Kingsbury thrust bearing is used with main propeller shaft?
- 1495.Which of the following statements describes the operating characteristics of a pre-combustion chamber?
- 1496.A Roots-type blower installed on a direct reversible engine __________.
- 1497.After cooling of the cylinder air charge of a turbocharged diesel engine will result in __________.
- 1498.Maximum rated horsepower of a diesel engine should be attained __________.
- 1499.Exhaust gases are generally removed from the cylinders of a two-stroke/cycle diesel engine by __________.
- 1500.White smoke exhausting from a diesel engine can be caused by __________.