USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 4
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 301.A safety valve on an auxiliary boiler simmers constantly and can not be stopped by several quick blow-offs using the hand relieving gear. The problem may be __________.
- 302.A burner responsible for producing black smoke in an automatic auxiliary boiler, would be caused by a __________.
- 303.Which of the following types of feed water regulators is commonly used with a water-tube, natural circulation, auxiliary boiler?
- 304.Fuel injection systems are designed to primarily meter fuel, atomize fuel, and __________.
- 305.An electric heater built into some smaller diesel engines is used to __________.
- 306.Which of the air intake systems listed will result in the lowest specific fuel consumption?
- 307.Engines having a bore exceeding 250 mm, but not exceeding 300 mm are to have at least __________.
- 308.An auxiliary boiler is equipped with a return flow fuel atomization system, which uses a/an __________.
- 309.Over firing of a hot water boiler may be caused by __________.
- 310.What is the speed of the crankshaft in a four-stroke/cycle engine when the camshaft is turning at 750 rpm?
- 311.The pressuretrol which is installed on an auxiliary boiler senses steam pressure changes and __________.
- 312.In a diesel engine closed freshwater cooling system employing a radiator, proper water temperature can be obtained by __________.
- 313.If the combustion control system of an automatically fired auxiliary boiler fails to relight the burner after a normal shutdown, you should check for a/an __________.
- 314.A waste heat boiler is installed on some diesel propelled vessels to __________.
- 315.Why should handhole gaskets not be allowed to leak on an auxiliary boiler?
- 316.Automatic combustion control systems for auxiliary boilers are designed to cycle burners on and off in response to the __________.
- 317.The variation in the amount of fuel oil burned in the operation of an auxiliary boiler, utilizing a return flow type atomization system, is a function of the __________.
- 318.Which of the following conditions could cause black smoke to be discharged from the stack of an auxiliary boiler equipped with turbine-driven rotary cup atomizers?
- 319.Camshafts are usually driven by timing gears or __________.
- 320.The main difference between an 'APF' and an 'APE' type fuel injection pump, is the design of the __________.
- 321.The maximum pressure developed by a waste heat boiler is determined by the main engine exhaust __________.
- 322.Which of the listed effects would mixtures of ethylene glycol and phosphate compounds have on the metal surfaces of the cooling system of a diesel engine?
- 323.Which of the listed parts on a fire-tube auxiliary boiler requires a written report to the Officer-in-Charge of Marine Inspection when renewed?
- 324.Automatic combustion control systems for some auxiliary boilers are designed to cycle burners on and off in response to __________.
- 325.Waterside scale in a fire-tube boiler may cause __________.
- 326.With regards to a diesel engine crankcase explosion, the most violent is the __________. I. primary explosion II. secondary explosion
- 327.When an auxiliary boiler is panting and emitting black smoke, you should __________.
- 328.Bottom blow valves are installed on auxiliary water-tube boilers to __________.
- 329.The reversing mechanism on a direct reversing large low-speed main propulsion diesel engine, operated by means of oil pressure, can serve to __________.
- 330.The correct procedure for giving an auxiliary boiler a bottom blow, is to begin __________.
- 331.If the chemical analysis of a lube oil sample taken from a diesel engine indicates an increased neutralization number the __________.
- 332.Additional explosion relief valves are fitted on separate spaces of the crankcase such as gear or chain cases for camshaft or similar drives when the __________.
- 333.A two stroke diesel engine exhaust temperature will be lower than a four stroke diesel engine of the same displacement because the __________. I. scavenging air is cooling the exhaust gases II. exhaust cycle time is longer
- 334.With which of the following types of diesel engine arrangements is a waste heat boiler most likely to produce the maximum steam pressure, temperature, and flow conditions?
- 335.During maintenance inspections of a fire tube auxiliary boiler, you should check for __________.
- 336.The constant capacity, pressure atomizing, fuel oil burners designed to meet a wide variation in the steaming loads of an auxiliary boiler, are __________.
- 337.The camshaft on a four-stroke/cycle diesel engine provides a means to operate the __________.
- 338.An 8000 horsepower diesel engine has a specific fuel consumption of 0.4 lbs. of fuel per horsepower hour. If each pound of fuel contains 18,500 BTU's and 25% of the available heat leaves the engine with the exhaust, how many BTU's per hour are theoretically available for use in a waste heat boiler?
- 339.Antifreeze solutions containing ethylene glycol, should not be mixed with corrosion protection oils, as the resultant mixture __________.
- 340.Coast Guard Regulations (46 CFR) permit tubular type water gage glasses on auxiliary boilers, provided the maximum allowable working pressure does not exceed __________.
- 341.In an automatically fired auxiliary boiler, restarting from the normal shutdown cycle in response to steam demand, is initiated by a/an __________.
- 342.Which of the following methods is typically employed in the design of waste heat boilers to obtain maximum heat transfer, while maintaining low overall weight?
- 343.According to Coast Guard Regulations (46 CFR), which of the following pressures is the highest boiler pressure where a tubular type gage glass may be installed?
- 344.At the beginning of the pre-purge period on an automatic auxiliary boiler equipped with a programmed control system, the unit will not restart if airflow is not sensed and __________.
- 345.A properly adjusted safety valve for an auxiliary boiler will __________.
- 346.Fuel injector nozzles are usually of the multi-orifice type with the number and placement of the holes arranged according to the __________.
- 347.Ethylene glycol, when used as a coolant in a closed cooling system for a diesel engine, is more advantageous than untreated raw water because it __________.
- 348.When conducting a hydrostatic test on a water-tube auxiliary boiler, the test water should be heated to a temperature of at least 70°F. This is done to __________.
- 349.A photoelectric cell installed in an automatically fired auxiliary boiler burner management system __________.
- 350.The maximum allowable working pressure on a packaged auxiliary boiler is 200 psig. The normal working pressure for one particular packaged boiler is 175 psig. Which of the following safety relief valve settings would be proper for this boiler?
- 351.The valve cam slope angle determines the __________.
- 352.The degree of fuel atomization in a diesel engine cylinder depends primarily on __________.
- 353.A smoking burner with a pulsating flame in an auxiliary boiler, is an indication that the __________.
- 354.On an automatically fired auxiliary boiler, the steam pressure limit switch is wired into the burner electric circuit to __________.
- 355.A variable capacity, pressure atomizing, fuel oil burner functions to __________.
- 356.The firing range of a variable capacity, return flow-type fuel atomizer is regulated to meet steam demand by varying the __________.
- 357.Excessive vibration from an auxiliary boiler could be caused by __________.
- 358.After lighting off a cold, automatically fired, auxiliary boiler, as steam begins to form, you should __________.
- 359.In a coil-type forced circulation auxiliary water-tube boiler __________.
- 360.The shape of a diesel engine cam determines the __________.
- 361.Which of the following devices is normally provided to prevent oil starvation in a diesel engine lubrication system utilizing the 'full flow' principle?
- 362.Corrosion inhibitors and/or soluble oils are added to diesel engine cooling systems to __________.
- 363.Cylinders diameters greater than 230 mm require additional safety devices when the scavenging spaces are openly connected to the cylinders. Which of the following devices will be used to protect such spaces?
- 364.If poor combustion occurs in an auxiliary boiler due to an air damper linkage being out of adjustment, you would adjust the linkage and then __________.
- 365.Which of the automatic boiler controls listed should be tested prior to lighting off an auxiliary boiler?
- 366.Which of the following conditions would cause 'panting' in a steaming auxiliary boiler?
- 367.The valve cam slope angle determines the __________.
- 368.A large low speed main propulsion diesel engine may become overloaded by___________________. I. a heavily fouled hull II. strong head winds and heavy seas
- 369.Which of the following statements concerning the operation of a coil-type forced circulation auxiliary water-tube boiler is correct?
- 370.If oil is dripping from the burner of a coil-type auxiliary steam generator, the cause may be __________.
- 371.Coast Guard Regulations (46 CFR) require electric hot water supply boilers to be provided with a/an __________.
- 372.Coast Guard Regulations (46 CFR) require the programming control sequence for auxiliary boiler operation to include __________.
- 373.In a forced circulation auxiliary boiler, steam is formed in the __________.
- 374.Ignition failure in an automatically controlled auxiliary boiler can be caused by __________.
- 375.The arrangement and shape of the cams on a diesel engine camshaft directly control which of the listed groups of operating conditions?
- 376.Fuel injectors used in heavy fuel oil systems are usually provided with cooling to reduce __________.
- 377.A spring-loaded relief valve is located on some lube oil filters in full flow systems to __________.
- 378.A diesel engine cooling water system with a pH factor of 3.0 indicates a condition of __________.
- 379.What is required for crosshead type engines that have a scavenging space in open connection to the cylinder?
- 380.A sudden flame failure in an operating auxiliary boiler, equipped with an automatic combustion control system and burning light fuel, could be attributed to a __________.
- 381.The flame safeguard controls of a large automatically fired auxiliary boiler, may consist of a __________.
- 382.Coast Guard Regulations (46 CFR) permit the use of which of the following fuel oil ignition methods on automatic auxiliary boilers?
- 383.Which of the following statements concerning fire-tube boilers is correct?
- 384.Which of the following statements about a coil-type forced circulation auxiliary water-tube boiler is correct?
- 385.In a diesel engine cooling water system, a pH of 6.0 indicates a/an __________.
- 386.Indirect cooling of fuel injector nozzle holders for diesel engines is accomplished primarily by __________.
- 387.In which of the following areas of a crosshead engine is a permanently connected fire extinguishing system required?
- 388.Ignition failure in an auxiliary boiler can be caused by __________.
- 389.The pH value of water in a diesel engine closed cooling water system should be maintained between __________.
- 390.The purpose of the safety relief valves installed on an auxiliary boiler is to __________.
- 391.An AC diesel generator incapable of being paralleled with the main bus normally employs an isochronous governor in order to __________.
- 392.The most common contaminate of governor hydraulic fluid is __________.
- 393.Which of the substances listed is satisfactorily removed from the fuel by a centrifugal oil purifier?
- 394.A magnetic strainer is primarily used in diesel engine reduction gear oil systems to remove small particles of __________.
- 395.A two stroke diesel engine exhaust temperature will be lower than a four stroke diesel engine of the same displacement because the __________. I. mep is lower and the scavenging air is cooling the exhaust gases II. valve overlap in a four stroke diesel engine is greater
- 396.Which of the following listed construction details of internal combustion engines is required?
- 397.The safety valve installed on a coil-type auxiliary boiler is located on the __________.
- 398.Which of the following statements is true concerning pressure limit switches and pressuretrols installed on auxiliary boilers?
- 399.A port-and-helix fuel injection pump having upper and lower plunger helixes is designed to __________.
- 400.In reducing engine speed to an efficient propeller speed by the use of reduction gears, __________.