USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 5
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 401.One advantage of hydraulic clutches over mechanical clutches in diesel engine installations is __________.
- 402.A diesel generator governor is hunting. After changing the oil the governor is flushed and the compensation needle valve is adjusted; but the hunting persists. You should NOW __________.
- 403.In order to reverse the rotation of a two-stroke/cycle loop scavenged, direct reversing, propulsion diesel engine, the cam positions must be changed for the __________.
- 404.Some fuel injection systems utilize port-and-helix metering. Which of the following statement describes a system 'timed for port closing'?
- 405.During a routine round of a diesel engine generator, you observe a low oil level in the governor sump. If there is no visible sign of external leakage, you should suspect the cause to be a/an __________.
- 406.A continuous fluctuation of the speed, due to over control by the governor, is known as __________.
- 407.Airflex clutches are used to transmit power from a diesel engine to the propeller shaft. A restricted orifice is used in the control air system of this unit to __________.
- 408.The purpose of try-cocks used on an auxiliary boiler is to __________.
- 409.When an additional load is applied to a diesel engine which is using an air bladder clutch unit that is inadequately inflated, you can expect __________.
- 410.A diesel engine is equipped with an isochronous hydraulic governor. A decrease in load will cause the engine speed to __________.
- 411.The reversing cams of some four-stroke/cycle diesel engines are brought into position by __________.
- 412.Which of the following statements describes a fuel injection pump marked 'timed for port closing'?
- 413.Internal combustion engines are to be fitted with governors to prevent the engines from exceeding the rated speed by more than __________.
- 414.Slippage of an air operated friction clutch can result from __________.
- 415.Misalignment of the drive shaft and propeller shaft flanges can be detected by using a dial indicator or __________.
- 416.The temperature at which an adjustable bellows type thermostatic valve operates is determined by __________.
- 417.In addition to the normal governor, each main engine having a maximum continuous output of 300 hp and over, which can be declutched or which drives a controllable pitch propeller, __________.
- 418.Where one or more diesel driven AC generators are operating in parallel, reducing the value of the speed droop to 'zero' on one unit will allow that unit to __________.
- 419.Increasing the load on an engine using a double-helix type injection pump varies the effective stroke of the pump to start __________.
- 420.Effective hydraulic coupling operation depends upon a certain amount of __________.
- 421.If the cooling water temperature and the lube oil temperature in a diesel engine are too high, the cause can be __________.
- 422.Most large main propulsion diesel engines use a duplex lube oil strainer to __________.
- 423.While inspecting the main bearings on a diesel engine you find impregnated dirt and scratches in the bearing surface. You would, therefore, suspect that __________.
- 424.The gage glass on a coil-type auxiliary boiler is connected to the __________.
- 425.The linear motion of a diesel engine piston is converted into the rotary motion required to drive gears, propeller shafts, and generators by the __________.
- 426.The port-and-helix metering pumps, used in diesel fuel injection systems, are usually designed to produce a constant beginning and a variable ending of fuel injection. These pumps are usually __________.
- 427.Where would a coarse screen wire-mesh strainer normally be found on a diesel engine lubrication system?
- 428.High diesel engine cooling water temperatures can be caused by __________.
- 429.Which of the listed problems would be indicated by an accumulation of water in one cylinder, in addition to the crankcase of an idle diesel engine?
- 430.One advantage of electromagnetic slip couplings is __________.
- 431.If a hydraulic governor has been refilled with oil, the engine should be operated until it reaches normal temperature, then the air should be purged, and the __________.
- 432.The rotary motion of a diesel engine crankshaft is obtained from the up and down motion of the piston via the __________.
- 433.Unusually low oil pressure in the lube oil header of a diesel engine is the result of a/an __________.
- 434.A diesel engine is operating at 1800 RPM and driving a propeller at 600 RPM. What is the speed reduction ratio?
- 435.The power loss associated with slip in a fluid coupling appears as __________.
- 436.The purpose of the compensating adjustment used in a diesel engine hydraulic governor is to __________.
- 437.When the steam pressure drops below a set value on an automatically fired auxiliary boiler, fitted with rotary cup atomizers, the combustion control system will __________.
- 438.The main reason counterweights are added to crankshafts is to __________.
- 439.An individual fuel injection pump is designed for variable beginning and constant ending of injection. For diesel engines operating a generator at constant speeds, the start of injection will __________.
- 440.Diesel engines driving alternators operating in parallel must maintain a set frequency regardless of load changes. The governor characteristic used to accomplish this is known as __________.
- 441.The control system for a controllable pitch propeller can be programmed __________. I. to produce a maximum combined propeller and engine efficiency between pitch and a given engine speed II. for continuous operation of the engine at pre-set conditions
- 442.At what pressure should a cylinder relief valve of an internal combustion engine be set to relieve?
- 443.When changing the direction of propeller shaft rotation in a diesel plant equipped with a pneumatic clutch, you must pause at neutral to allow the __________.
- 444.A viscous damper, as used on a marine diesel, is a sealed precision built device which dampens the torsional vibrations in the __________.
- 445.The end of fuel injection in a port-and-helix metering pump can be controlled by __________.
- 446.Loss of lubricating oil pressure to the main propulsion diesel engine will actuate a/an __________.
- 447.Higher than normal jacket water temperatures occurring in all cylinders of a diesel engine can result from a/an __________.
- 448.If the operating speed of a diesel engine increases without an apparent change in the engine control settings, you may suspect a __________.
- 449.Automatically fired auxiliary boilers use fuel oil strainer arrangements of either the simplex type or __________.
- 450.When centrifuging heavy fuel oil, an important factor to consider is the __________. I. flow rate II. viscosity of the fuel oil
- 451.A crankshaft whose center of gravity coincides with its center line is said to be __________.
- 452.The amount of fuel injected in a particular time, or degree, of crankshaft rotation is termed __________.
- 453.In a normally operating diesel engine, the main source of lubricating oil contamination in the crankcase is a result of the __________.
- 454.Which of the following problems will cause above normal cooling water temperatures in a diesel engine using a closed freshwater cooling system?
- 455.Which of the following statements represents an advantage of an electromagnetic clutch?
- 456.Two air compressors are provided for the starting air system and should be capable of __________.
- 457.Which of the following adjustments is always required whenever the diesel engine governor oil has been drained and renewed?
- 458.The air supplied to a diesel engine is compressed to __________. I. provide heat for the ignition of the fuel II. decrease injection delay
- 459.The possibility of damage from operating a diesel engine at critical speeds is reduced by the use of __________.
- 460.On small diesel engines, a noticeable decrease in the time interval between the replacement of the lube filter cartridge indicates __________.
- 461.If the jacket water temperature of an operating diesel engine suddenly rises above normal, the cause can be attributed to __________.
- 462.On a diesel engine equipped with a hydraulic speed control governor, hunting in many cases can be corrected by adjusting the __________.
- 463.In an auxiliary boiler steam and water system, the highest pressure will be in the __________.
- 464.How is the diesel engine operating RPM affected when a 'ZERO DROOP' setting is selected on the governor?
- 465.A dirty diesel engine oil filter element can best be detected by __________.
- 466.If the coolant temperature of a closed cooling water system for a diesel engine gradually increases, the trouble usually is __________.
- 467.Which of the following statements concerning the lubrication of diesel propulsion engines used in vessels over 300 gross tons is most accurate?
- 468.In an electromagnetic coupling, torque to the driven shaft is limited by the __________.
- 469.If an auxiliary diesel engine will not crank but can be barred over, the trouble may be __________.
- 470.Increasing the load on an engine equipped with a constant speed mechanical governor, will cause the engine speed to initially __________.
- 471.The small end of the connecting rod is attached to the piston with a __________.
- 472.When the lower edge of the spiral begins to uncover the release port in a jerk pump, the __________.
- 473.The pressure differential across a diesel engine lube oil system duplex filter should be checked to __________.
- 474.Some diesel engines are fitted with a thermometer in the cooling water outlet from each cylinder. If the cooling water temperature from all cylinders begins to rise above normal, you should suspect __________.
- 475.Proper operation of the main engine reduction gear set requires the operator to monitor __________.
- 476.The fuel oil strainers in the fuel oil service system of an automatically fired auxiliary boiler are permitted by the Coast Guard Regulations (46 CFR) to be either the simplex type or the __________.
- 477.The torque transmitted by an electromagnetic induction coupling for an auxiliary diesel is dependent upon excitation and the __________.
- 478.On a diesel engine equipped with an isochronous governor, if the 'speed droop' control is reduced to the 'zero' setting, the engine __________.
- 479.The duration of fuel injection developed by an individual port-and-helix fuel injection pump, is determined by the __________.
- 480.What could cause the bypass valve in a full-flow lubrication system to open?
- 481.You are operating a main propulsion diesel engine at a constant load when the jacket water temperature begins to rise. This could be caused by __________.
- 482.Where the size and design of an engine is such that lubrication before starting is not necessary and an attached pump is normally used, __________.
- 483.When air is delivered under pressure to one of the glands of an air-bladder clutch, the __________.
- 484.Wear occurring at the tips of the reduction gear teeth is usually the result of __________.
- 485.The amount of fuel injected into a cylinder by a unit injector is controlled by __________.
- 486.Before starting a diesel engine that has an engine driven lube oil pump, the engineer should __________.
- 487.The principal purpose of refractory and insulation installed in the firebox of an auxiliary boiler is to __________.
- 488.If an engine operates at 900 RPM at no load, and at 870 RPM at full load, the speed droop is __________.
- 489.When two direct air start reversible medium speed diesel engines are coupled in parallel to a common propeller shaft, which of the operating conditions listed will apply during extended periods of maneuvering?
- 490.Air bubbles in a hydraulic governor can cause __________.
- 491.The amount of fuel delivered for each cycle must be in accordance with the engine load, and the same quantity of fuel must be delivered to each cylinder for each power stroke at that load. Which of the following statements describes this requirement?
- 492.Fuel oil transfer systems used onboard diesel propelled vessels are required to have __________.
- 493.Fins are installed on the fireside of the water-tubes, used in waste heat boilers, to __________.
- 494.If a main propulsion diesel engine hunts excessively at idle speed, you should __________.
- 495.At dead center, the centerline of the connecting rod usually coincides with the __________.
- 496.Immediately after starting a diesel engine, normal raw water and jacket water pressures are indicated. However, the jacket water temperature continues to rise. If there is no change in the sea temperature, you should suspect __________.
- 497.In a simple hydraulic governor with speed droop, oil under pressure is maintained ready for use in the __________.
- 498.The hunting of a diesel engine may be caused by __________.
- 499.Auxiliary boilers can be classified as __________.
- 500.Fins are installed on the fireside of the water-tubes used in waste heat boilers to __________.