USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 7
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 601.Governors used on diesel engines to limit the load must be equipped with __________.
- 602.The ability of a fuel particle to travel into the combustion chamber before burning is called __________.
- 603.The effective stroke of a constant-stroke, individual, fuel injection pump is varied by the __________.
- 604.Insufficient piston cooling for a large, low-speed, main propulsion diesel engine burning heavy fuels, can result in __________.
- 605.A piston in a four-stroke/cycle diesel engine makes four strokes during each __________.
- 606.The lower section of a piston is called the __________.
- 607.The function of the window cast into the housing of an individual jerk pump is to __________.
- 608.Which of the following conditions is most likely to occur if oil containing moisture is continuously fed to a purifier operating as a clarifier?
- 609.Scale and dirt accumulation in the waterside of a lube oil cooler will be indicated by a gradual increase in the lube oil __________.
- 610.Which of the following statements is an accurate description of fuel injection piping used on diesel engines with a cylinder bore of 250 mm and above?
- 611.A change in the degree of fuel atomization in a diesel engine would most greatly affect __________.
- 612.Which of the following devices is a common basic element with nearly all mechanical governors?
- 613.Theoretical perfect combustion in a diesel engine yields by-products of __________.
- 614.Gear-type flexible couplings are often used in diesel engine drive trains because they __________.
- 615.In a bypass type lubrication system for a diesel engine, the dirty oil line to the centrifuge should be taken from the __________.
- 616.Which of the following factors tends to increase scale formation on the saltwater side of a heat exchanger used in a diesel engine cooling water system?
- 617.If the peak to peak pressure pulsation in the diesel engine fuel injection return piping exceeds 285 psi what special provision is to be provided?
- 618.Diesel engine exhaust temperatures may be used to indicate __________.
- 619.In a diesel engine, a leaking exhaust valve can cause __________.
- 620.When used with reversing reduction gears, main propulsion diesel engines should be bolted tight to their foundations with fitted bolts at the output drive end and snug bolts with elongated bolt holes at the opposite end. This is done to __________.
- 621.In a diesel engine mechanical-type fuel pump, the delivery check valve is opened by __________.
- 622.What is the term given to the process of breaking up fuel oil into very fine particles for better combustion?
- 623.The most severe cavitation erosion occurring on the waterside of diesel engine wet cylinder liners normally occurs __________.
- 624.For a given fuel, a change in the compression ratio will affect the ignition lag by which of the listed means?
- 625.Turbulence in a diesel engine cylinder is of major importance in providing __________.
- 626.The required amount in the change of speed necessary before a governor will make a corrective movement is known as __________.
- 627.Which of the following problems may occur if the opening pressure of a fuel injection nozzle is greater than specified by the engine manufacturer?
- 628.In a full floating wristpin, the pin is prevented from sliding against the cylinder walls by __________.
- 629.Exhaust valve grooving and corrosion is caused by certain components of residual fuel oil. These components are sodium, sulfur, and __________.
- 630.Whether using a centrifuge or a simple filter, oil cleaning and filtration will be the most effective when the oil is at a __________.
- 631.Cavitation erosion in the cooling water system of a diesel engine usually occurs at the pump impeller, and on the waterside of the __________.
- 632.High firing pressures and a low exhaust temperature in a diesel engine may result from __________.
- 633.Poor combustion in a diesel engine can be caused by __________.
- 634.After each speed change, the compression of the diesel engine governor speeder spring is returned to a constant value, regardless of the amount of movement of the fuel control mechanism and engine load. Hence, this results in __________.
- 635.Fuel oil discharged into the diesel engine cylinder is atomized at the __________.
- 636.The longer the ignition delay period occurs in a diesel engine, the __________.
- 637.The load is always placed on the lower half of the main bearings in a/an __________.
- 638.Which term describes piston pins having bearing surfaces in both the piston bosses and connecting rod eye?
- 639.Diesel engine fuel oil leakage should be drained and additional precautions provided to __________.
- 640.The easiest way to locate a defective diesel engine exhaust valves is by __________.
- 641.Which of the following devices is common to both mechanical and hydraulic governors?
- 642.Which of the following conditions will tend to increase the ignition delay period of combustion in a compression ignition engine?
- 643.A flexible coupling is located between the __________.
- 644.Exhaust pyrometer readings provide an indication of the __________.
- 645.When is fuel injected into a cylinder of diesel engines?
- 646.Injection lag can be caused by __________.
- 647.If the raw water supply pressure for a diesel engine cooling system is below normal, you should check for a __________.
- 648.A change in the degree of fuel atomization in a diesel engine cylinder has the greatest effect on the __________.
- 649.In most marine single reduction gear units, the bull gear is driven by the __________.
- 650.The rate of pressure rise during the period following initial fuel ignition in a diesel engine, is influenced chiefly by the __________.
- 651.A change in engine speed is required before a governor is able to make a corrective movement of fuel rack. This aspect of governing is commonly expressed as a percent and is known as __________.
- 652.On most diesel engines, the governor controls the output speed by __________.
- 653.Proper dispersion of fuel in a diesel engine cylinder is dependent upon the __________.
- 654.Piston cooling fins are located __________.
- 655.Compared to other fuel injection systems, unit injectors operate with virtually no __________.
- 656.When cleaning a duplex strainer, it is important for __________.
- 657.In a closed cooling water system, which of the following problems can cause the water pressure to fluctuate?
- 658.Why is it necessary to compress the air charge in the cylinders of a diesel engine?
- 659.The average exhaust temperature of a two-stroke/cycle diesel engine with a turbine-driven supercharger is lower than a similar four-stroke/cycle diesel engine at equal loads because __________.
- 660.Diesel fuel oil having a low cetane rating can result in __________.
- 661.Besides the use of piston cooling fins to assist in cooling, they also provide extra strength for the piston __________.
- 662.Differential needle valves used in fuel injectors are directly closed by __________.
- 663.A dirty lube oil strainer can result in __________.
- 664.In a closed cooling system for a turbocharged, four-stroke/cycle diesel engine, fluctuating water pressure can be caused by __________.
- 665.The governor controlling a diesel engine modulates crankshaft RPM by adjusting the __________.
- 666.High exhaust temperature and black smoke exhausting from an auxiliary diesel engine can be caused by __________.
- 667.Individual cylinder performance in a diesel engine is routinely determined by exhaust gas __________.
- 668.Any increase in the exhaust back pressure of a four-stroke/cycle diesel engine will __________.
- 669.The driving force of a propeller is transmitted to the hull through the_________________.
- 670.If fuel injection to a four-stroke/cycle diesel engine begins earlier than designed, ignition may be delayed because the __________.
- 671.In a full flow type lube oil system, the bypass relief valve will lift due to __________.
- 672.Which of the following problems can cause fluctuating pressures in the closed cooling system of a main propulsion diesel engine?
- 673.Which of the following statements is correct concerning diesel engine cooling water systems?
- 674.Which of the following statements concerning the factors affecting ignition delay is correct?
- 675.Air motion is induced in a four-stroke/cycle diesel engine cylinder to improve air fuel mixing, and is known as __________.
- 676.Trunk type diesel engine pistons are effectively cooled when heat is __________.
- 677.The minimum fuel oil delivery pressure required for efficient injection depends primarily on the __________.
- 678.An increased pressure differential between the inlet and outlet of a strainer usually indicates the strainer is __________.
- 679.A diesel engine with a combustion chamber located between the crowns of two pistons is known as a/an __________.
- 680.In a diesel engine, the initial crosshatching of the cylinder liner surface aids in __________. I. rapid ring seating II. the retention of lube oil
- 681.Persistent knocking in one cylinder of an eight cylinder diesel engine would MOST likely be caused by __________.
- 682.To successfully reduce an excessively high diesel engine exhaust gas temperature, you should __________.
- 683.Which of the two events listed occurs simultaneously in a two-stroke/cycle diesel engine?
- 684.High exhaust back pressure will result in an increase in __________.
- 685.A loop or cross scavenged engine utilizes the motion of its pistons and a turbocharger to provide scavenging air. Which of the listed mechanical designs prevents the air under the pistons from being pumped back through the scavenge ports during the piston power stroke?
- 686.Which of the following statements concerning a closed type fuel injection nozzle is true?
- 687.To determine if the lube oil filter elements need changing, __________.
- 688.Combustion gas venting through the expansion tank can be caused by a __________.
- 689.Diesel engine control can be obtained by the bridge __________.
- 690.Which of the following statements is correct for the design and installation of diesel engine cooling water systems?
- 691.Combustion knock can occur in the cylinders of a diesel engine under any condition permitting __________.
- 692.One of the most common methods in preventing a diesel engine piston pin from contacting the cylinder wall is by the use of __________.
- 693.The injection pressure of a hydraulic fuel injection nozzle can be increased by __________.
- 694.Many lube oil filters have pressure gages installed on both the inlet and outlet in order to indicate the pressure drop across the filter. In normal operation, the pressure drop will __________.
- 695.A cracked cylinder head on a diesel engine may be indicated by __________.
- 696.Control of the main propulsion diesel engines can be shifted from the engine room to the wheelhouse from the __________.
- 697.Exhaust pipes of multiple engine installations are not to be interconnected, but are to be run separately to the atmosphere __________.
- 698.Excessive diesel engine cylinder exhaust back pressure will be caused by __________.
- 699.A thrust bearing is used with a propulsion diesel engine to __________.
- 700.In a large slow-speed propulsion diesel engine, the force applied to the piston is __________.