USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 11
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1001.The cylinder liner forming the cylinder wall and the inside of the water jacket is called a __________.
- 1002.In a diesel engine, late fuel injection is indicated by black or gray exhaust smoke with __________.
- 1003.Some diesel engines are supercharged with a __________.
- 1004.In a coil-type forced circulation auxiliary water-tube boiler, __________.
- 1005.A diesel engine valve spring is under compression when the valve is __________. I. Open II. Closed
- 1006.Misalignment of the drive shaft and propeller shaft flanges can be detected by using a dial indicator or __________.
- 1007.A diesel engine will lose power if fuel injection occurs too late in the cycle, because the __________.
- 1008.In a diesel engine, blow-by __________.
- 1009.The process of supplying a diesel engine cylinder with air at a pressure greater than atmospheric is called __________.
- 1010.The purpose of an interference angle in a diesel engine exhaust valve is to __________. I. break up seat deposits II. work in conjunction with valve rotators to rotate the valve
- 1011.A four cylinder, four stroke/cycle, single acting diesel engine has a 740 mm bore and a 1500 mm stroke. What indicated power will be developed if the average mean effective pressure is 18 kg/cm2 at a speed of 90 RPM?
- 1012.Excessive piston ring wear in a diesel engine will cause __________.
- 1013.Which of the contaminants listed would remain in the lube oil after filtering?
- 1014.Late fuel injection timing is indicated by __________.
- 1015.If the analysis of used lube oil indicates a high content of iron particles, this could indicate __________.
- 1016.The exhaust system for a turbocharged diesel engine functions to __________.
- 1017.Which type of pump is typically used to supply fuel to a unit type auxiliary boiler?
- 1018.In a medium speed diesel engine, a trunk type piston may be cooled by __________. I. oil circulation though passages in the piston crown II. heat transfer through piston rings and liner wall
- 1019.In a diesel engine jacket water cooler, with seawater cooling the fresh water, the __________.
- 1020.Late fuel injection in a diesel engine is indicated by low firing pressure with __________.
- 1021.If an analysis of a sample of used engine lube oil shows a high concentration of sodium nitrite, this probably indicates that __________.
- 1022.Which of the following beneficial results can be expected from supercharging a previously naturally aspirated engine?
- 1023.If an auxiliary diesel engine coolant temperature is higher than normal, but the thermostat is determined not to be defective, you would suspect a/an __________.
- 1024.The microbiological growths that affect fuel supplies can easily be transported from one location to another by __________.
- 1025.The pressure differential across a diesel engine lube oil system duplex filter should be checked to __________.
- 1026.Late fuel injection occurring at, or after TDC in a diesel engine is indicated by excessive exhaust smoke and __________.
- 1027.If the plunger or barrel of a fuel injection jerk pump becomes damaged, __________.
- 1028.When one cylinder has a lower compression pressure and higher exhaust gas temperature than any of the other engine cylinders, which of the conditions listed will be indicated?
- 1029.What is the average piston speed of a seven-cylinder, two-stroke/cycle diesel engine with a 580 mm bore and a 1700 mm stroke operating at 100 RPM?
- 1030.Starting aids such as glow plugs, are installed on __________.
- 1031.The bore of a diesel engine cylinder describes the __________.
- 1032.Late fuel injection in a diesel engine is indicated by low firing pressure with __________.
- 1033.Which of the listed pre-start procedures should be carried out prior to starting a crosshead type diesel engine after an overhaul?
- 1034.The direct acting mechanical governor used with some small diesel engines, controls fuel flow to the engine by __________.
- 1035.Late fuel injection in a diesel engine is indicated by black or gray exhaust smoke with a __________.
- 1036.A decrease in the flash point of the diesel engine lube oil indicates the lube oil is __________.
- 1037.A supercharged diesel engine, when compared to a similar naturally aspirated diesel engine, will develop an increase in __________.
- 1038.According to Coast Guard Regulations (46 CFR), the maximum allowable boiler pressure in which a tubular gage glass may be installed is __________.
- 1039.If the speeder spring of a main propulsion diesel engine governor breaks while operating at full load, the engine RPM will __________.
- 1040.The sludge tank installed in the diesel engine room is used to collect __________. I. sludge from the fuel oil centrifuge II. water that has been collected in the settling tank.
- 1041.If a few injector spray holes become plugged, the result could be __________.
- 1042.Which of the following conditions is most likely to occur when unburned fuel contaminates the crankcase of a diesel engine?
- 1043.Which of the following conditions is realized by the turbo charging of a previously naturally aspirated diesel engine?
- 1044.A piston is said to be at top dead center when it is __________.
- 1045.If the speed of a turbocharged diesel engine is maintained constant the turbocharger speed will __________.
- 1046.At top dead center, the centerline of the connecting rod usually coincides with the __________.
- 1047.Why are some diesel engine cylinder liners plated on the wearing surface with porous chromium?
- 1048.A distorted spray pattern from a fuel injector can cause a diesel engine to have __________.
- 1049.Which of the listed bearing types is an example of a solid bearing?
- 1050.The process of scavenging a two-stroke/cycle diesel engine serves to __________.
- 1051.In a diesel engine, what is the advantage of pre-combustion chambers over the open type of combustion chamber? I. Pre-combustion chambers permit coarser fuel atomization. II. Pre-combustion chambers allow lower fuel injection pressure.
- 1052.A diesel generator has just been paralleled with an AC turbo generator, but the load can not be properly divided. This could be caused by __________.
- 1053.The term 'diesel engine cylinder scavenging' means __________.
- 1054.Most large main propulsion diesel engines use duplex lube oil strainers to __________.
- 1055.In a large low-speed diesel engine, excessive piston clearance from the cylinder head can be restored by __________.
- 1056.A method of finishing diesel engine cylinder walls to aid in the proper ring seating and lubrication is known as __________.
- 1057.Plugged spray holes in a diesel engine fuel injector will cause excessive smoking at idling speed, in addition to __________.
- 1058.One device used to determine the amount of fuel dilution of diesel engine lube oil is a/an __________.
- 1059.Air scavenging of a diesel engine cylinder __________.
- 1060.The upper leveling plates in a Kingsbury thrust bearing are held in place by __________.
- 1061.A distorted furnace in a fire-tube auxiliary boiler may be the result of __________.
- 1062.Higher than normal temperature air passing through the intake of a diesel engine will result in __________.
- 1063.After a long period of operation, a wear ridge, caused by piston ring action, will develop near the top of the cylinder liner. This ridge must be removed during maintenance in order to prevent __________.
- 1064.Distortion of the spray pattern of a nozzle or injector may be indicated by a/an __________.
- 1065.Lube oil filters can be used to remove most contaminants from lube oil. Which of the contaminants listed would remain in the lube oil after filtering?
- 1066.A diesel engine is supercharged in order to __________.
- 1067.A properly honed diesel engine cylinder liner will __________.
- 1068.When the opening pressure of a diesel engine fuel injector is greater than that specified by the engine manufacturer, which of the following problems can be expected?
- 1069.Which of the following conditions could be a cause of excessive fuel dilution of diesel engine lube oil?
- 1070.When a fuel injection nozzle overheats, which of the problems listed can be expected?
- 1071.Fuel oil contamination of an auxiliary diesel engine lube oil can result in __________.
- 1072.Which of the following devices will increase the power output of a diesel engine without increasing its frictional load?
- 1073.A diesel engine piston crown can crack from __________.
- 1074.Scavenging in a turbocharged, four-stroke/cycle diesel engine is accomplished __________.
- 1075.The lower water seal on a diesel engine wet cylinder liner must allow for liner axial movement. This seal is most commonly a __________.
- 1076.Diesel engine lube oil can become contaminated as a result of __________.
- 1077.Which of the following statements represents the proper order of thrust transmission when a Kingsbury thrust bearing is used with diesel propulsion?
- 1078.Which of the diesel engine cylinder liners listed has internal cooling water passages?
- 1079.If a single cylinder relief valve on a diesel engine lifts frequently while the engine is running, the cause may be an __________.
- 1080.Which of the following conditions indicates the dilution of diesel engine lube oil by fuel oil?
- 1081.Which of the turbo charging systems listed operates with the least average back pressure in the exhaust manifold?
- 1082.The exhaust valve opens before bottom dead center in a four stroke engine to___________. I. allow for blow down II. reduce pumping losses
- 1083.An operating turbocharged diesel engine that suddenly loses power, is due to a/an __________.
- 1084.A dry-type exhaust muffler clogged with soot, will cause __________.
- 1085.Which of the following problems will occur if the needle valve in a fuel injection nozzle sticks in the open position?
- 1086.One simple laboratory analysis of used lube oil that can be carried out aboard ship is called the __________.
- 1087.Which of the turbo charging methods listed directs the exhaust gases to the turbine at fairly uniform velocity and pressure?
- 1088.The lower water seal on a diesel engine wet cylinder liner must allow for liner expansion and contraction. This seal is most commonly a __________.
- 1089.A bendix drive starting motor disengages the drive gear from the flywheel by __________.
- 1090.In a diesel engine, pistons are attached to the crankshaft by __________.
- 1091.It is easier to replace a dry cylinder liner than a wet one because __________.
- 1092.If the needle valve in a fuel injection nozzle sticks open, __________.
- 1093.Intake air flow from a diesel engine turbocharger is directly proportional to engine __________.
- 1094.Which instrument is used to take crankshaft deflection readings?
- 1095.One advantage of dry cylinder liners used in a diesel engine is the __________.
- 1096.An incorrect spray pattern produced by a diesel engine fuel injection nozzle can be directly caused by __________.
- 1097.The purpose of an interference angle in a diesel engine exhaust valve is to __________. I. seat the valve quickly II. break up seat deposits
- 1098.One characteristic of a pulse type turbo charging system is __________.
- 1099.The purpose of the delivery check valve used in a diesel fuel injection jerk pump is to __________. I. assist in a quick cutoff of fuel injection II. prevent fuel oil backflow from the injection pump
- 1100.One of the advantages in the use of a dry liner over a wet liner is __________.