USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 16
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1501.A four-stroke eight cylinder in-line medium speed diesel engine has a firing order of 1-5-2-6-8-4-7-3. If #8 piston is at TDC and firing, how many degrees of camshaft rotation will occur when #1 piston reaches TDC and fires?
- 1502.Before being shut down, a diesel engine should idle a few minutes in order to __________.
- 1503.Significant retardation of diesel engine fuel injection timing will result in __________.
- 1504.The power consumed during the scavenging process of a diesel engine is known as the __________.
- 1505.What is the function of a diesel engine's stationary parts?
- 1506.The main advantage of unit injectors over other fuel injection systems is __________.
- 1507.When associated with main propulsion diesel engines, shaker, circulation, and spray are the three general methods used in __________.
- 1508.The main difference between an 'APF' and an 'APE' jerk type fuel injection pump, is the __________.
- 1509.When overhauling a diesel engine, the best tool to use to remove the wear ridge at the top of the engine cylinder liner, prior to removing the piston, is __________.
- 1510.The light and medium fuels utilized in diesel engines also provide a source of __________.
- 1511.Low compression in a diesel engine could be caused by __________.
- 1512.The most rapid period of fuel combustion and cylinder pressure increase in a diesel engine should begin just before the piston reaches top dead center and should be completed __________.
- 1513.In some modern large slow speed diesel engines, which of the following is used as the support for the main bearings?
- 1514.A diesel engine cylinder has a swept volume of 104 cubic inches and a clearance volume of 8 cubic inches at top dead center. What is the compression ratio of the engine cylinder?
- 1515.In general, diesel engine waste heat boiler construction is usually of the _____________.
- 1516.A diesel engine cylinder has a swept volume of 130.5 cubic inches and a clearance volume of 9.0 cubic inches at top dead center. What is the compression ratio of the engine cylinder?
- 1517.Before installing rings on a diesel engine piston, you should check the ring __________.
- 1518.The adverse effects of burning high sulfur fuel can be compensated for by using a lubricating oil having sufficient __________.
- 1519.Coast Guard Regulations (46 CFR) require that small automatic auxiliary boilers shall be equipped with a pre-purge programming control that will assure at least __________.
- 1520.When checking zincs in a saltwater cooled heat exchanger, you should __________.
- 1521.Which of the combustion parameters listed is used in a diesel engine, but NOT related to the injection system?
- 1522.The piston wrist pin used in some diesel engine pistons is prevented from contacting the cylinder wall by a __________.
- 1523.You are installing new piston rings on a single acting diesel engine piston. To check the ring gap clearance, the rings should be placed at the __________.
- 1524.Low compression in a diesel engine could be caused by __________.
- 1525.The small clearances existing between each of the blower lobes, and between the lobes and casing of a Roots-type blower, must be maintained to __________.
- 1526.Precision engine bearing inserts are manufactured with a small portion of the bearing ends extending beyond the bearing housing or caps. This design provides for positive seating and is commonly referred to as bearing __________.
- 1527.The amount of wear on a split precision main bearing can be most accurately determined by comparing the data from a previous reading to the present readings taken with a __________.
- 1528.When the timing gear backlash for a Roots-type blower has become excessive, the problem is properly repaired by __________.
- 1529.The small end of a connecting rod for an auxiliary diesel is attached to the piston with a __________.
- 1530.An eight cylinder, four stroke/cycle, single acting diesel engine has a 650 mm bore and a 1400 mm stroke. What will be the indicated power developed if the average mean effective pressure is 30 kg/cm2 at a speed of 100 RPM?
- 1531.If an auxiliary diesel engine will not crank but can be barred over, the trouble may be in the __________.
- 1532.To minimize corrosion in a metal-edge strainer used in a fuel oil system, strainer disks, spacers and scraper blades are commonly made of __________.
- 1533.When a diesel engine is operated with a piston ring having a cold gap clearance less than that recommended by the manufacturer, the ring will __________.
- 1534.The average exhaust temperature of a two-stroke/cycle diesel engine with a turbine-driven supercharger is lower than a similar four-stroke/cycle diesel engine at equal loads because __________.
- 1535.In a two-stroke/cycle, opposed piston, diesel engine, the lower crankshaft operates several crankshaft degrees in advance of the upper crankshaft to __________.
- 1536.Irregular engine speed in a diesel can be caused by __________.
- 1537.A common method for diesel engine piston cooling is to deliver oil through the connecting rod into a void space in the piston head and then allow the piston motion to distribute the oil to cool the piston crown and drain the oil back to the crankcase. This procedure is known as the __________.
- 1538.Which of the following problems may occur if the clearance between a piston and cylinder liner is insufficient?
- 1539.What would be the result of adding phosphate compounds into the cooling system of a diesel engine ? I. Protect the coolant from freezing. II. Protect metallic surfaces from corrosion.
- 1540.Which of the following precautions should be taken when cleaning the air filter on a diesel engine equipped with a turbocharger?
- 1541.The pressure in an operating diesel engine cylinder continues to rise for a short period after the piston passes top dead center as a result of the __________.
- 1542.If an auxiliary diesel engine will not crank but can be barred over, the trouble may be due to __________.
- 1543.In a diesel engine, maximum lube oil system pressure under cold start conditions, is normally controlled by __________.
- 1544.Which of the following conditions can cause above normal air temperature to develop in the intake manifold of a four-stroke/cycle, turbocharged, diesel engine?
- 1545.A visual inspection of the chrome plated piston compression rings at the liner ports reveals vertical brown streaks on the face of the rings. This condition indicates __________.
- 1546.A SECONDARY function of a waste heat boiler is to __________.
- 1547.On a four-cycle diesel engine, the valve subjected to the most severe conditions during normal service is the __________.
- 1548.Which of the following conditions may contribute to the formation of deposits on the blades of the turbocharger turbine?
- 1549.Maintaining the proper fuel oil temperature will result in __________.
- 1550.If a diesel engine is difficult to start when operating in low ambient temperature conditions, you should suspect that the __________.
- 1551.How is the pressure and temperature affected in a diesel engine cylinder during compression?
- 1552.In a large main propulsion diesel engine, if an excessive amount of carbon has been found to be forming around the fuel injector nozzle holes, which of the following would correct this condition?
- 1553.High lube oil temperature developing in a diesel engine generally results from __________.
- 1554.An examination of the piston compression rings of an efficiently operating diesel engine, should appear with a __________.
- 1555.Early fuel injection in a diesel engine cylinder will generally result in __________.
- 1556.A 18 cylinder medium speed direct reversible main propulsion diesel engine is being operated with one cylinder secured. When the engine was stopped, the affected cylinder stopped in a position preventing the engine from being restarted. Which of the following actions should be taken to correct the situation?
- 1557.Following the failure of one turbocharger on a large, crosshead, main propulsion diesel engine, fitted with multiple turbochargers, which of the following actions should be taken prior to further operation of the engine?
- 1558.On an opposed-piston engine, increasing the lower crank lead will result in which of the listed operating conditions?
- 1559.A large two-stroke/cycle direct reversing diesel engine is to be reversed. Prior to the admission of starting air you must __________.
- 1560.If a diesel engine can be turned over at normal cranking speed but fails to start, the cause could be late fuel injection or __________.
- 1561.If a diesel engine turned over at normal cranking speed but failed to start, the cause could be late fuel injection or __________.
- 1562.A disadvantage of a four-stroke/cycle over a two-stroke/cycle diesel engine is __________.
- 1563.A bright shiny appearance of the sealing surfaces on diesel engine compression rings indicates __________.
- 1564.Which of the air intake systems listed will require the least amount of brake horsepower to operate?
- 1565.The device most commonly used to measure the exhaust gas temperature of a diesel engine cylinder is called a __________.
- 1566.Which of the listed adjustments must be made to a naturally aspirated four-stroke/cycle diesel engine if a turbocharger is to be installed?
- 1567.The theoretical minimum compression ratio necessary to ensure compression ignition in a direct injection diesel engine is ___________.
- 1568.Visual inspection of chrome-plated piston compression rings reveals a black ring face at the position of the cylinder liner ports. This condition indicates a ring which __________.
- 1569.The face surface appearance of a shallow groove, stainless steel, chrome plated compression ring should exhibit through its operating life a __________.
- 1570.Which of the changes in the valve timing listed should be carried out when a naturally aspirated four-stroke/cycle diesel engine is converted to a supercharged engine?
- 1571.When inspecting piston rings through the ports of a two-stroke/cycle diesel engine, black areas on the sealing surfaces are the result of __________.
- 1572.When a naturally aspirated four-stroke/cycle diesel engine is converted for supercharging, which of the following changes must be made to the valve timing?
- 1573.Black areas on the sealing surfaces of piston rings indicate __________.
- 1574.Which condition indicates the air side fouling of an after cooler on a turbocharged diesel engine?
- 1575.If sludge accumulates on the underside of a diesel engine piston, it will __________.
- 1576.Which of the following conditions can cause below normal air pressure in the intake manifold of a turbocharged diesel engine?
- 1577.Which of the conditions listed occurring in a diesel engine would cause carbon deposits to develop in the piston ring belt?
- 1578.Failure to remove the carbon ridge at the top of the cylinder when removing a piston may result in __________.
- 1579.Which of the following problems can cause an above normal air temperature to develop in the intake manifold of a turbocharged and after cooled diesel engine?
- 1580.In accordance with Coast Guard Regulations (46 CFR), which of the listed starting aids is acceptable for use with the emergency diesel generator?
- 1581.If the turbocharger of a four-stroke/cycle diesel engine fails to operate properly, which of the following statements best describes the probable effect?
- 1582.A substance found in residual fuels which tends to cause exhaust valve corrosion and grooving, is __________.
- 1583.If a crankcase explosion occurs in a diesel engine, which of the listed actions should be taken?
- 1584.Which of the following statements is true regarding the installation of piston rings on two-stroke/cycle, diesel engines as compared to four-stroke/cycle, diesel engines?
- 1585.Which of the following precautions must be taken if an electric immersion heater is used to keep the coolant warm in a diesel engine when the engine is secured?
- 1586.The manufacturer of a particular diesel engine recommends when running on heavy fuel for the vanadium content not to exceed 300 ppm. If there are 10 ounces of vanadium per 3125 pounds of fuel just taken on board, which of the following statements is co
- 1587.If a crankcase explosion occurs in a diesel engine, you should stop the engine and __________.
- 1588.The service life of a worn aluminum piston for an auxiliary diesel, for which no spares are readily available, can be extended by __________.
- 1589.Coast Guard Regulations (46 CFR) state that emergency diesel generator starting systems must have sufficient capacity to provide at least __________.
- 1590.If the turbocharger failed on an auxiliary four cycle diesel engine, which of the following conditions would probably occur?
- 1591.The desirable properties of a marine fuel oil should include __________.
- 1592.If a diesel engine has been stopped because of piston seizure due to severe overheating, the crankcase __________.
- 1593.Which of the following conditions can result in the cracking of the piston lands?
- 1594.Which of the listed devices is the only method allowed by Coast Guard Regulations (46 CFR), to ease the starting of emergency generator engines?
- 1595.A sudden power loss from a turbocharged and after cooled diesel engine is an indication of a/an __________.
- 1596.Heavy fuel oils generally have an upper average ash content of 0.1% by weight. Which of the following conditions could be expected if the ash content increases above this amount?
- 1597.If a crankcase explosion has occurred in a diesel engine, and the crankcase remains intact, which of the following precautions should be observed?
- 1598.Excessive side clearance between a piston ring and its groove will cause the ring to __________.
- 1599.Cold weather starting of a diesel engine may be made easier by __________.
- 1600.A thin film of oil on the lobes of a Roots-type blower indicates __________.