USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 18
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1701.Which of the bearings listed below is most widely used for the main and connecting rod bearings of a modern high-speed diesel engine?
- 1702.For optimum results, centrifugal purification of heavy fuel oil should be accomplished with the fuel at the lowest practicable __________.
- 1703.In a diesel engine, blow-by is generally the result of worn __________.
- 1704.The valve stem expansion associated with engine warm-up is allowed for by the __________.
- 1705.Heavy residual fuel oils are heated prior to centrifuging to __________.
- 1706.One cause of diesel engine piston ring blow-by is __________.
- 1707.Bearing clearances in small high-speed diesel engines should be measured with __________.
- 1708.Which type of starter motor is normally used in a diesel engine hydraulic starting system?
- 1709.Diesel engine 'blow-by' into the crankcase is caused by excessive ring __________.
- 1710.Which type of motor listed is most commonly used in hydraulic starting systems for diesel engines?
- 1711.A centrifuge will satisfactorily remove which of the following contaminants from fuel oil?
- 1712.When an engine fitted with a hydraulic starting system starts up, the starter is protected from the higher speed of the engine by __________.
- 1713.If fuel oil were being discharged from the waste water outlet of a fuel oil disk type centrifuge, operated as a separator, you should __________.
- 1714.In a diesel engine, blow-by is a result of combustion gases leaking into the crankcase past the __________.
- 1715.In a Bendix starter drive, the pinion engagement with the flywheel ring gear is initiated by __________.
- 1716.Diesel engine blow-by is the leakage of combustion gases past the __________.
- 1717.In a diesel engine starting motor equipped with a Bendix drive, the pinion moves and meshes with the flywheel ring gear due to __________.
- 1718.The camshaft on a four-stroke/cycle diesel engine is used to operate the __________.
- 1719.If the bowl of a disk type centrifugal purifier when operated as a separator is not primed, the __________.
- 1720.In large, low-speed, main propulsion diesel engines, piston ring groove wear usually occurs at the __________.
- 1721.A diesel engine cylinder head can crack as a result of __________.
- 1722.The use of push rods becomes necessary in a diesel engine when __________.
- 1723.If diesel fuel was discharging from the waste water outlet of a disk type centrifugal purifier operating as a separator you should __________.
- 1724.The ring lands on a large, low-speed, main propulsion diesel engine piston may crack due to __________.
- 1725.Which of the listed design features is found in an exhaust valve and NOT in an intake valve?
- 1726.In an auxiliary diesel engine, one reason for knurling the piston skirt is to __________.
- 1727.Many diesel engine exhaust valves are being constructed with hollow stems filled with sodium in order to __________.
- 1728.Marine auxiliary diesel engine starters utilizing Bendix drive gear are powered by an electric starting motor or __________.
- 1729.In a diesel engine, which type of wrist pin uses bearings in the piston bosses, but is fixed to the small end of the connecting rod?
- 1730.Poor quality fuel being used in a turbocharged medium-speed, diesel engine could result in __________.
- 1731.If clearance between a piston and the cylinder wall is excessive, piston slap will occur. The slap itself is caused by __________.
- 1732.A built-up exhaust valve is one in which __________.
- 1733.Brake specific fuel consumption is given in units of __________.
- 1734.Which of the following statements concerning cylinder liner wear is true?
- 1735.Valve rotators are commonly used on which of the listed diesel engine cylinder head valves?
- 1736.To reduce the weight of the reciprocating parts, pistons of high-speed engines are made considerably shorter. This results in __________.
- 1737.When comparing different fuels for different engines, the ignition quality of the fuel oil becomes a less critical consideration as __________.
- 1738.Scuffed cylinder liner surfaces in a diesel engine can result from __________.
- 1739.The adverse effects of burning high sulfur fuel can be compensated for by using a cylinder oil having sufficient __________.
- 1740.A turbocharged, four-stroke/cycle diesel engine has a larger valve overlap than a naturally aspirated, four-stroke/cycle diesel engine in order to increase the __________.
- 1741.Electric starting motors for diesel engines require high current for operation and __________.
- 1742.Piston cooling fins are located __________.
- 1743.If the oil scraper ring drain hole in a diesel engine piston becomes plugged, __________.
- 1744.Auxiliary diesel engine electric starting motors use __________.
- 1745.Many cast iron pistons are designed with heat dams, which serve to __________.
- 1746.If the piston groove drain holes for the oil control rings become clogged, which of the following is likely to occur?
- 1747.During the process of cylinder scavenging, the size of the exhaust valve opening is __________.
- 1748.Diesel engine electric starting motors generally require heavier duty motors and operate at higher voltages than comparable starting motors for gasoline engines due to __________.
- 1749.If the compression rings on a diesel engine piston become stuck in the ring groove, the cause may be due to __________.
- 1750.Exhaust valve openings in a two-cycle diesel engine cylinder head are made as large as practical to __________.
- 1751.Cold clearances between the skirt of an aluminum piston and the cylinder liner is about __________.
- 1752.Improperly fitted piston rings in a diesel engine can result in __________.
- 1753.Exhaust gases are generally removed from the cylinders of a two-stroke/cycle diesel engine by __________.
- 1754.Diesel engine piston seizure can be caused by __________.
- 1755.In the cylinder head of a two-stroke/cycle diesel engine, valves are used for __________.
- 1756.A six-cylinder, two-stroke/cycle diesel engine is fitted with a rotary distributing air starting system. The speed of the rotating distributor disc is __________.
- 1757.Incomplete combustion in a running diesel engine can cause piston rings to become stuck as a result of __________.
- 1758.The exhaust system for a turbocharged two-stroke/cycle diesel engine functions to __________.
- 1759.One end of a diesel engine cylinder is sealed by the cylinder head and the other end by the __________.
- 1760.A sudden drop in compression pressure in one cylinder of a diesel engine can be caused by __________.
- 1761.The most common instrument used to measure diesel engine exhaust pressure is the __________.
- 1762.In a two-stroke/cycle, opposed piston, diesel engine, one crankshaft operates several crank angles in advance of the other crankshaft to __________.
- 1763.When monitoring diesel engine performance, the most useful instrument to use is the __________.
- 1764.The difference in crank lead between the upper and lower cranks of an opposed piston engine causes the lower crankshaft to __________.
- 1765.In an opposed piston engine, which of the following events would happen if the lower crank lead were reduced from 12° to 0°?
- 1766.Worn main bearings in a diesel engine can result in __________.
- 1767.A pyrometer is an instrument commonly used to measure __________.
- 1768.During the power stroke of a four-stroke/cycle diesel engine, most of the side thrust of a trunk-type piston is absorbed by the __________.
- 1769.Low compression pressure in a diesel engine can be caused by __________.
- 1770.A pyrometer is an instrument used to measure the temperature of the diesel engine __________.
- 1771.Low compression pressure in a diesel engine is caused by __________.
- 1772.Thermocouple pyrometers are used on large, main propulsion diesel engines to indicate the temperature of the __________.
- 1773.A connecting rod in a four-stroke/cycle diesel engine is subject to __________.
- 1774.When the air valve is opened to admit starting air to a diesel engine pneumatic starting motor, the valve should be opened rapidly to __________.
- 1775.Low compression pressure in a diesel engine may be the result of __________.
- 1776.For a diesel engine, individual cylinder performance is commonly determined by exhaust gas __________.
- 1777.Diesel engine air start system check valves are opened by __________.
- 1778.In a four-stroke/cycle diesel engine, the intake valves open __________.
- 1779.Low compression in a diesel engine can be caused by __________.
- 1780.Pyrometers commonly found on diesel engine exhaust systems, consist of __________.
- 1781.Excessive valve lash in an auxiliary diesel engine will cause the valves to open __________.
- 1782.Which of the general advantages listed does the electrical pyrometer have over the mechanical pyrometer?
- 1783.When an air started, four-stroke/cycle diesel engine is being cranked over, the starting air is admitted to each cylinder during the beginning of its __________.
- 1784.Which of the listed problems can be a cause of low compression pressure in a diesel engine?
- 1785.Which of the diesel engine exhaust mufflers listed is usually equipped with a spark arrestor?
- 1786.When the cold valve lash is less than that specified by the manufacturer, diesel engine valves, operating at normal temperatures, will __________.
- 1787.Low cylinder compression pressure and a high exhaust temperature may indicate __________.
- 1788.A dry-type spark arrestor removes sparks from a diesel engine exhaust by __________.
- 1789.If a four-stroke/cycle diesel engine is started by admitting high pressure air into the cylinders, the pistons receiving the charge of starting air must be __________.
- 1790.If the valve lash on a diesel engine is set improperly, which of the following statements represents the most serious problem that can develop?
- 1791.A drop in compression pressure in one cylinder of a diesel engine can be caused by __________.
- 1792.In a medium-speed marine propulsion engine equipped with direct admission air starting valves, the cylinders without air starting valves fire first because the __________.
- 1793.If you increase the clearance between a valve stem and rocker arm, which of the listed conditions will occur?
- 1794.An eight cylinder, air started, two-stroke/cycle, direct reversing, marine diesel engine can be rotated from any crankshaft position by the air start system only if it has __________.
- 1795.Reducing the clearance between a valve stem and rocker arm will result in the valve __________.
- 1796.Which of the listed conditions can cause lacquer to be deposited on a piston skirt?
- 1797.In accordance with Coast Guard Regulations (46 CFR) regarding internal combustion engine exhaust manifold installations, which of the following statements is true?
- 1798.Which operating condition of a diesel engine is indicated by excessive firing pressures?
- 1799.In a diesel engine, after ignition of the fuel occurs, but before the piston reaches TDC, there is little change in the cylinder __________.
- 1800.Coast Guard regulations (46 CFR) require a horizontal dry exhaust pipe from a diesel engine must __________.