USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 6
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 501.Connecting rods in a diesel engine are used to connect the __________.
- 502.The term 'proper metering', as applied to a diesel fuel injection system, can be best defined as __________.
- 503.The magnetic lock between the armature and field in an electromagnetic coupling is established by __________.
- 504.The main propulsion diesel engine jacket water temperature rises above normal, with the raw water sea suction and the expansion tank water level being normal. Which of the following problems is most likely the cause?
- 505.When fuel oil heaters are required for main engine operation, __________.
- 506.The rate of heat transfer in a water-tube auxiliary boiler can be increased by __________.
- 507.Which of the couplings listed will prevent shock loads from being transmitted to an engine?
- 508.Governor hunting is caused by __________.
- 509.In a diesel engine, pistons are attached to the crankshaft by __________.
- 510.Regarding jerk-type fuel pumps as used on some auxiliary diesel engines, the delivery cutoff point is controlled with a __________.
- 511.A diesel engine using lube oil with too high a viscosity will exhibit __________.
- 512.Some diesel engines are fitted with a thermometer in the cooling water outlet from each cylinder. If the cooling water temperature from an individual cylinder begins to rise, you should suspect __________.
- 513.Large steam drums are not required in the design of a coil-type auxiliary water-tube boiler because __________.
- 514.If the compensating needle valve of a hydraulic governor is opened more than necessary the governor will __________.
- 515.The plunger in a jerk pump is rotated until the release port is uncovered. If the port remains uncovered all of the time, which of the listed operations will occur?
- 516.Immediately after any diesel engine is started, the engineer should first check the __________.
- 517.One result of operating a diesel engine at light load with excessively low cooling water temperatures is a/an __________.
- 518.Piping from booster pumps to injection systems are to be at least __________.
- 519.The best method for determining the amount of eccentricity or offset misalignment between the disconnected propeller shaft coupling flange and the reduction gear output flange is by using a __________.
- 520.Hydraulic couplings will transmit torque equal to the input torque by means of energy changes in a rotating vortex of liquid. For the vortices to form, there must be __________.
- 521.In diesel engines designed with a crosshead, the motion of the piston rod can be described as __________.
- 522.Which of the following will occur when the lower edge of the spiral, on the plunger of a jerk pump, uncovers the spill port?
- 523.If the jacket water temperature in an auxiliary diesel engine cooling system is lower than normal, the probable cause is __________.
- 524.Before any work is done on a burner in an automatically fired auxiliary boiler, you should always __________.
- 525.If the a main propulsion diesel engine governor works irregularly with a jerking motion, a possible cause can be __________.
- 526.When reassembling the bowl of a disk-type centrifuge, the bowl or locking ring is rotated __________.
- 527.Pitting in the area close to the pitch line and on the same end of each gear tooth of a reduction gear unit would be caused by __________.
- 528.Which of the components listed is only found in an opposed piston engine?
- 529.To guarantee that a reduction gear bearing is receiving proper oil supply, you should check the __________.
- 530.If the coolant temperature is excessively low as it passes through the internally cooled fuel injectors, the injectors may be damaged by __________.
- 531.Valves and fittings used with diesel engine fuel oil pressure piping may be threaded in sizes up to and including 60 mm O.D., but screwed unions __________.
- 532.Constant capacity, pressure atomizing, fuel burners designed to meet a wide variation in steaming loads on an auxiliary boiler, are __________.
- 533.Adjustments to the compensating needle valve in a hydraulic governor should be made with the engine at __________.
- 534.The fuel oil strainers located in the fuel oil service system of an automatic auxiliary heating boiler are either the duplex type or the __________.
- 535.Which of the following design features will reduce the possibility of overheating the top compression rings of a cast iron piston?
- 536.In an electromagnetic slip coupling, the slip __________.
- 537.Which of the listed diesel engine operating conditions should be checked immediately after any diesel engine is started?
- 538.When a diesel engine is attached to a reduction gear, diesel engine speed is reduced and the torque available for work __________.
- 539.Which of the couplings listed is normally not repairable, and is usually replaced if completely damaged?
- 540.The purpose of a heat dam used in some diesel engine cast iron pistons is to __________.
- 541.Immediately after starting a small high-speed diesel engine, you should check the __________.
- 542.Prolonged operation of a diesel engine with a closed cooling water system, at lower than normal designed operating temperatures can __________.
- 543.Valves used in diesel engine fuel oil pressure piping are to be __________.
- 544.Auxiliary boilers are divided into several classifications, one of which is __________.
- 545.A diesel engine with a full speed of 1000 RPM drives a propeller at 300 RPM. What is the speed reduction ratio?
- 546.A faulty thermostatic bypass valve, in a diesel engine cooling system, can result in __________.
- 547.Auxiliary boilers are divided into several classifications, one of which is __________.
- 548.One of the most common causes of reduction gear failure is gear wear caused by scoring as a result of __________.
- 549.The purpose of the separating nozzle in the accumulator of a water-tube, coil-type, steam generator is to separate __________.
- 550.A direct acting, pneumatically controlled governor for a diesel engine operates in a range of 10 to 50 psi. The fuel rack position is at 20 millimeters when the governor air pressure is 30 psi. If the governor air pressure changes to 20 psi, the fuel rack setting will change to __________.
- 551.The major cause of trouble in a mechanical-hydraulic governor is contamination of the hydraulic fluid by __________.
- 552.Cast iron pistons used in large propulsion diesel engines are constructed with __________.
- 553.Which of the listed substances can be satisfactorily removed from diesel fuel by centrifuging?
- 554.An emergency diesel generator cooling system is equipped with an automotive type thermostat. If the thermostat bellows loses its charge, the thermostat will __________.
- 555.Which of the following statements is correct concerning ABS rules for fuel oil injection systems as found on diesel propelled vessels?
- 556.Downcomers installed on auxiliary package boilers are protected from direct contact with hot gases by __________.
- 557.Pitted reduction gear teeth having a deep blue color with evidence of overheating have been operated with __________.
- 558.Which of the listed problems will happen when the water level of a fire-tube type auxiliary boiler approaches the crown sheet?
- 559.Compensating needle valve adjustments to a hydraulic governor should be made with the engine __________.
- 560.The upper section of a piston is called the __________.
- 561.A waterside fusible plug, installed in a fire-tube auxiliary boiler __________.
- 562.Which of the following characteristics is true relative to meshing spur gears?
- 563.Engine displacement is equal to the cylinder __________.
- 564.When passing through mesh contact, the teeth of a reduction gear first go through a series of actions best described as __________.
- 565.The fusible plugs used in fire-tube auxiliary boilers are installed in the __________.
- 566.A main propulsion diesel engine is fitted with a pneumatically actuated governor, having an operating range of 10 to 60 psig. The current fuel rack setting is 15 mm at 30 psig. If the air pressure to the governor is increased to 40 psig, the fuel rack setting will change to __________.
- 567.Why is the ring belt narrower in diameter than the skirt of a piston designed for a diesel engine?
- 568.Cooling water pumps driven by direct-reversing diesel engines are usually __________.
- 569.If the operating element of a thermostatic valve installed in a diesel engine cooling system malfunctions, it may result in __________.
- 570.In a diesel engine, excessive cylinder liner wear will cause __________. I. increased blowby II. wear between the piston ring and groove
- 571.To correct a hunting problem in a main propulsion diesel engine hydraulic governor, you should __________.
- 572.The color of the engine exhaust from a diesel propelled ship should be __________.
- 573.Which of the listed governor operating characteristics is considered to be isochronous?
- 574.The diameter of a piston is usually less at the crown than at the skirt, in order to __________.
- 575.On a diesel engine equipped with individual jerk type fuel pumps, adjustments should be made to the tappets (push rods) of the pumps to __________.
- 576.Which of the following manufacturing methods is recommended for diesel engine fuel injection line piping?
- 577.The power output of a turbocharged diesel engine will drop if the cooling water flow through the after cooler is interrupted because the __________.
- 578.A burned exhaust valve may be detected by a higher than normal __________.
- 579.Helical reduction gears, as used with main propulsion drive trains, are constructed so that several teeth are meshed at the same time to __________.
- 580.What occurs in the combustion space of a diesel engine cylinder shortly after ignition and before the piston reaches TDC?
- 581.Successful combustion inside the cylinders of a diesel engine is dependent upon __________.
- 582.An advantage of aluminum pistons, when compared to cast iron pistons is __________.
- 583.The air bladder clutch used with some reversing reduction drive gears, consists of __________.
- 584.Which of the following conditions will develop if the flow of 'raw' cooling water to a diesel engine is obstructed?
- 585.Which of the listed conditions will occur if a diesel engine exhaust valve is leaking?
- 586.Fuel oil penetration into the cylinder of a diesel engine is __________.
- 587.Precombustion chambers, and energy cells in high-speed, small bore diesel engines all serve to increase ____________.
- 588.Some medium and high-speed diesel engines require reduction gear units to provide a useful propeller speed. In most reduction gears, the bull gear __________.
- 589.If the piston stroke in a four stroke cycle diesel engine is 10 1/2 inches and the speed of rotation of the crankshaft is 720 RPM, what is the average piston speed?
- 590.Which of the following statements best describes the operational characteristics of an isochronous governors?
- 591.The fuel injection pumps on a diesel engine are controlled by a linkage system attached to the __________.
- 592.What type of fitting is to be used on diesel engine fuel injection line piping?
- 593.Improper cooling of a diesel engine cylinder liner due to the accumulation of scale deposits, may cause __________.
- 594.Diesel engine exhaust gas temperatures can be used to determine individual cylinder __________.
- 595.The volume of available air supply required by an air clutch varies with the __________.
- 596.The principal characteristic of an isochronous governor is it will __________.
- 597.Which statement about diesel engine combustion is true?
- 598.All of the diesel engine cylinder firing pressures are normal, yet all of the exhaust temperatures are low. Which of the following situations is responsible for this condition?
- 599.Keel coolers fouled with marine growth, will result in __________.
- 600.Proper atomization of fuel in diesel engine combustion chambers will __________.