USCG Motor Plants and Auxiliary Boilers – Question Bank Book 14 (BK14) — page 8
1960 questions with correct answers from the official USCG question bank (2008 edition), book 14 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 701.Fuel supplied by each unit injector on a two-stroke/cycle single acting diesel engine is directed into each cylinder at a very high pressure through the __________.
- 702.Turbulence of the compressed air charge in a diesel engine cylinder increases __________.
- 703.A cracked cylinder head in an operating engine may be indicated by __________.
- 704.Combustion knock occurring in a diesel engine can be caused by __________.
- 705.Which of the following problems could develop due to the accumulation of oil vapors in the crankcase of a diesel engine?
- 706.The time between injection and ignition of the fuel is known as __________.
- 707.During the power stroke, the side thrust of a trunk type piston is a result of the angle __________.
- 708.One problem resulting from a diesel engine fuel injector opening pressure being lower than specified by the engine manufacturer, is that the __________.
- 709.Lube oil cannot be efficiently filtered if its __________.
- 710.A crack in a cylinder liner can be caused by __________.
- 711.An exhaust pipe from a internal combustion engine may not need to be insulated when __________.
- 712.When oil vapor, oxygen and hot spots are present at the same time within a crankcase, which of the following hazards could develop?
- 713.For a given size engine, the two-stroke/cycle diesel engine will deliver more power than a four-stroke/cycle diesel engine because __________.
- 714.A sudden drop in diesel engine cylinder compression pressure can be caused by __________.
- 715.Ring groove inserts are occasionally used on aluminum alloy pistons to __________.
- 716.The minimum speed an engine must attain before ignition can occur depends upon __________.
- 717.Lube oil filters remove contaminants from oil more efficiently if the oil being filtered is __________.
- 718.Coolant can be lost from a diesel engine jacket cooling water system by leakage from __________.
- 719.An automated diesel engine should normally shut down due to __________.
- 720.Which of the listed conditions is most likely to cause a crankcase explosion?
- 721.Which of the following statements pertains to propulsion engines with bores exceeding 200 mm?
- 722.A V-12 four-stroke/cycle 500 horsepower diesel engine is operating under a normal load, the firing pressures are low and the exhaust temperatures are high. Which of the following problems is the most probable cause of this condition?
- 723.An overcorrecting and unstable engine governor operation is known as __________.
- 724.Proper filtering and straining of diesel fuel is important because the __________.
- 725.Lube oil filters remove contaminants more efficiently if the oil being filtered is __________.
- 726.Diesel engine automated control systems may utilize sensing devices of dual function, with sensing ranges providing both alarm and engine shut down capability. Which of the key points listed would only require an alarm sensor?
- 727.Crankcase explosions in propulsion diesel engines result from __________.
- 728.Which of the items listed causes a direct acting mechanical governor to operate the engine fuel control linkage?
- 729.Thin bronze rings are inserted in the face of some chromium plated piston rings to __________.
- 730.The two strokes of a two-stroke/cycle diesel engine are __________.
- 731.Reduction gear casings are vented in order to __________.
- 732.Which of the conditions listed may occur in an operating diesel engine if air pockets form within the cylinder head circulating water passages?
- 733.Air receivers installed in starting air systems are to be __________.
- 734.Critical speed in diesel engines occurs when engine torque pulsations become __________.
- 735.In the Otto cycle, the fuel/air mixture is ignited at what point and by what means?
- 736.Which of the listed reasons is the most likely cause of a sudden drop in compression pressure in one diesel engine cylinder?
- 737.What is the function of the main thrust bearing?
- 738.Heat damage to fuel injection nozzles can be prevented by avoiding __________.
- 739.Failure to ensure proper venting of the cooling system of a diesel engine can result in __________.
- 740.In a diesel engine, the time period between fuel injection and ignition is usually defined as __________.
- 741.Failure to open the diesel engine test cocks after a long period of shutdown, prior to starting may result in __________.
- 742.The knock occurring when a cold diesel engine is started and continues while running at low speed, but stops when the engine reaches normal operating speed and temperature, is __________.
- 743.If a diesel engine's exhaust temperature is abnormally high, the cause could be __________.
- 744.The ability of the governor to prevent fluctuations in engine speed is termed __________.
- 745.In a simple mechanical governor, the __________.
- 746.To minimize the formation of carbon deposits on fuel injection nozzles, you should __________.
- 747.If the water level dropped rapidly in the expansion tank of a closed diesel engine cooling water system, you should suspect a __________.
- 748.Each receiver in a starting air system which can be isolated from a relief valve __________.
- 749.The intake air ducting to a diesel engine should not draw from an area on deck where flammable vapors released from tanks are present, because __________.
- 750.A gear type flexible coupling is precision built for __________.
- 751.A diesel engine piston ring face is in direct contact with the __________.
- 752.Injectors for use with heavy fuel oil may be internally cooled by either water or light oil to __________.
- 753.Which of the following conditions can cause oil to accumulate in the cooling system of a diesel engine?
- 754.Which of the types of reduction gearing listed is best suited for medium speed main propulsion units?
- 755.Vessels having main engines arranged for air starting are to be provided with at least __________.
- 756.Kingsbury thrust bearings are lubricated by __________.
- 757.Fuel is ignited in a diesel engine cylinder by __________.
- 758.In a diesel engine, the time taken to heat the fuel particles, turn them into vapor, and bring about combustion is called __________.
- 759.The function of diesel engine piston compression rings is to __________.
- 760.If the coolant temperature is too low as it passes through internally cooled fuel injectors, the injectors can be damaged by __________.
- 761.Direct reversible main propulsion diesel engines would normally be fitted with a/an __________.
- 762.The principal hazard to personnel when using a diesel engine fuel nozzle tester is ___________.
- 763.A possible cause for an individual piston to knock when at TDC on a slow-speed, two-stroke/cycle main propulsion diesel engine could be due to __________.
- 764.A diesel engine is operating with excessively high exhaust temperatures at all cylinders. To correct this condition, you should FIRST __________.
- 765.Excessive diesel engine back pressure may be an indication of __________.
- 766.The main reason for using bimetallic piston rings is to __________.
- 767.In order to start a large, low-speed, main propulsion diesel engine on high viscosity fuel after an extended shutdown, the __________.
- 768.Lube oil accumulating in the cooling water system of a diesel engine will result in __________.
- 769.The device used to limit engine torque at various engine speeds is called a __________.
- 770.Which of the speeder springs listed is more suitable for a governor installed on an engine operating over a wide speed range?
- 771.In a diesel engine, internal combustion causes the piston to be moved by __________.
- 772.A secondary function of diesel engine piston rings is to __________.
- 773.When a nozzle tester is being used to test a 'closed' type fuel injection nozzle, a clogged nozzle orifice will be indicated by a __________.
- 774.Where engine bores exceed 230 mm, a bursting disc or flame arrester is to be fitted __________.
- 775.Engine coolant accumulating in the diesel engine lubricating oil can result from a __________.
- 776.Persistent knocking of one cylinder of a diesel engine ceases when the fuel supply to that cylinder is secured. This problem may be a result of __________.
- 777.In a Kingsbury thrust bearing, the thrust shoes are __________.
- 778.The purpose of the energy cell, or air cell, is to __________.
- 779.Which of the listed components will ensure equal continuous pressure on the thrust shoes of a Kingsbury thrust bearing?
- 780.Barrel face, taper face, grooved, and chrome plated are all types of diesel engine __________.
- 781.You are testing a closed fuel injection nozzle using a nozzle tester. A pressure slightly less than design valve opening pressure is applied. If no fuel appears at the spray tip, the __________.
- 782.Diesel engines are classified as reciprocating internal combustion engines because they __________.
- 783.When more than one propulsion diesel engine is connected to a single propeller shaft through reduction gears, the gears are usually __________.
- 784.A main propulsion diesel engine is normally shut down by __________.
- 785.The efficient burning of fuel in a diesel engine is dependent upon the __________.
- 786.What type of reduction gear would most commonly be used with twin medium-speed propulsion diesel engines driving a single shaft?
- 787.Which of the equal horsepower diesel engines listed, running at the same speed, is least affected by exhaust back pressure?
- 788.Diesel engine piston ring gaps can be straight or angle cut. In comparison, the angle cut ring __________.
- 789.The total air capacity for non-reversible main engines is to be sufficient for __________.
- 790.To properly clean the disks of a metal-edge type strainer in a diesel engine lube oil system, you should __________.
- 791.What is the best way of stopping an over speeding diesel engine?
- 792.The thermal energy produced by an internal combustion engine is transformed into __________.
- 793.One remedy for a high firing pressure, in addition to a high exhaust temperature in one cylinder of a diesel engine, is to __________.
- 794.During combustion, the sealing surfaces of a diesel engine piston ring are considered to be the ring area in contact with the cylinder wall, in addition to the ring area in contact with the ring groove __________.
- 795.The blower type crankcase ventilation system __________.
- 796.One cylinder of a diesel engine is persistently knocking and does not cease when the fuel supply to that cylinder is secured. Which of the following problems may be the cause?
- 797.Routine monitoring of a diesel engine should include __________.
- 798.Which of the listed designs is effectively used to provide the turbulence necessary for proper combustion in a diesel engine cylinder?
- 799.The over speed trip installed on most diesel engines will stop the engine by shutting off the __________.
- 800.Improper seating of an air starting check valve in an operating diesel engine is indicated by __________.