USCG Steam Plants – Question Bank Book 13 (BK13) — page 5
1769 questions with correct answers from the official USCG question bank (2008 edition), book 13 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 401.A boiler internal feed pipe is perforated to __________.
- 402.When the flow of oil admitted to a disk-type centrifugal purifier is in excess of its designed capacity, which of the following conditions will usually occur?
- 403.The gland exhaust fan draws steam and non-condensable vapors from the gland exhaust condenser and discharges to the __________.
- 404.The water level in a steaming boiler has risen to within 2 inches of the top of the top gage glass. Your immediate action should be to __________.
- 405.Insufficient combustion air supply will cause an atomizer flame to appear as a __________.
- 406.The purpose of the diffuser in a boiler burner assembly is to __________.
- 407.Prior to relieving the watch you should first check the fire room status by verifying the boiler steam drum level and _________.
- 408.A nozzle in an impulse turbine functions to __________.
- 409.Steam baffles are used in the steam drum of a water-tube boiler to __________.
- 410.Which of the following chemicals is used in an Orsat apparatus to absorb carbon dioxide?
- 411.Any feed water testing done on a routine basis would normally include testing for __________.
- 412.When raising vacuum on an auxiliary condenser, which of the following steps is necessary?
- 413.When operating under constant load, the superheated steam temperature may rise above normal if the __________.
- 414.Assuming all burners are clean and the fuel oil is at the correct temperature, it is considered good practice to adjust the excess air until a light brown haze is obtained. With the aid of a chemical based flue gas analyzer, the percentage readings (not necessarily in order) should indicate __________.
- 415.The measured gap between the face of the burner atomizer tip nut and the diffuser plate, is determined by the setting of the __________.
- 416.Chemicals are added to boiler water by injecting them __________.
- 417.The size of the discharge ring used in a lube oil purifier is determined by the oil's __________.
- 418.Combustion gases can leak into the fire room through __________.
- 419.Coast Guard Regulations (46 CFR) prohibit which of the following pipe fittings from being installed in fuel oil service discharge piping?
- 420.Natural circulation in a marine boiler is a result of __________.
- 421.While vacuum is being raised on the main unit and the turbine warmed, condensate is re-circulated to the main condenser to __________.
- 422.Why should a boiler furnace be purged before the first burner is lit off?
- 423.The diffuser of a burner register assembly __________.
- 424.Which of the following precautions should be observed when adding treatment chemicals to the boiler compound tank?
- 425.Scavenging air is supplied to steam soot blower elements to __________.
- 426.When a turbine rotor is not rotating during maneuvering, the heat tends to be concentrated at the __________.
- 427.Which of the valves listed should be closed before lighting off a boiler?
- 428.The bulk of the solid material entering a centrifugal purifier with lube oil is __________.
- 429.Excess free oxygen in the boiler feed water can be the result of __________.
- 430.In a marine condenser designed with a reheating hotwell, the hotwell is reheated by __________.
- 431.Black smoke issuing from the boiler stack can be caused by an improper fuel/air ratio and by __________.
- 432.When used as a separator, a centrifugal purifier may lose its seal and cause __________.
- 433.In a water-tube boiler, sludge is most likely to collect in the __________.
- 434.Longitudinal expansion of a boiler water drum is allowed for at the boiler __________.
- 435.Slag buildup on boiler furnace refractory is undesirable because it causes __________.
- 436.A boiler is to be secured in port. After the burners have been secured, the forced draft fan and air registers should be secured __________.
- 437.The major reason dissolved gases are removed from boiler feed water is because they may cause __________.
- 438.Water-tube boiler screen tubes protect which of the listed components from high furnace temperatures?
- 439.If the boiler uptake periscope appears completely dark, this could indicate __________.
- 440.Any abnormal condition or emergency occurring in the fire room must be immediately reported to the __________.
- 441.What boiler water chemistry is necessary to ensure the precipitation of hard scale forming calcium?
- 442.Prior to lighting a burner in a cold boiler, you should __________.
- 443.The jacking gear on main propulsion turbines can be used to __________.
- 444.Water is best removed from lubricating oil by __________.
- 445.Excessive water loss from the main feed system can be caused by __________.
- 446.With the steam control valve wide open during normal operation, the rate of steam flow from the auxiliary exhaust steam line to the DC heater is actually a function of __________.
- 447.Water circulation in a water-tube boiler is a result of the __________.
- 448.If a boiler is smoking black and increasing the boiler front air box pressure does not reduce the smoke, the cause can be __________.
- 449.To safely reduce a high water level in a steaming boiler, you should __________.
- 450.The primary difference between sludge and scale deposits in boiler tubes is __________.
- 451.If the gage glass water level remains constant in a steaming boiler while maneuvering, the most probable cause is a __________.
- 452.The jacking gear is used in preparation for starting a marine turbine and reduction gear unit to __________.
- 453.Severe priming in a boiler can cause damage to the __________.
- 454.In accordance with Coast Guard Regulations (46 CFR), the normal operating pressure of a water-tube boiler must be stamped on the __________.
- 455.Which of the following represents one of the most important considerations in the design and location of the boiler internal feed pipe?
- 456.Zincs are installed in the main and auxiliary condenser water boxes to __________.
- 457.The possibility of a flareback in a boiler will be reduced if you __________.
- 458.Boiler stack gas temperature could be higher than normal if __________.
- 459.Which ring dam arrangement should be used for centrifugal purification?
- 460.Scale prevention in boiler water is accomplished by adding treatment chemicals to __________.
- 461.When a boiler has been secured and is being initially cooled, the water level showing in the steam drum gage glass should be __________.
- 462.If steam is admitted to the main propulsion turbine with the jacking gear engaged, which of the following problems can occur?
- 463.In a boiler, water flows downward in tubes furthest from the fires and flows upward in tubes nearest the fires because __________.
- 464.Air trapped within the main condenser shell is detrimental because it will __________.
- 465.When an oil purification centrifuge loses a portion of its seal, the oil can then be discharged through the heavy phase discharge port. This is partly a result of greater __________.
- 466.In a steaming boiler, higher than normal stack gas temperature can be caused by __________.
- 467.After restoring the normal water level in a boiler following a high water casualty, you should __________.
- 468.The most effective way to eliminate sludge from the water drum of a boiler is to __________.
- 469.The water seal in a centrifuge, operating at normal speed, prevents the lube oil from discharging from the water outlet. Another function of the seal is to __________.
- 470.The axial position of a turbine rotor is normally adjusted by varying the thickness of the __________.
- 471.Which of the actions listed should be carried out immediately after securing the fires in one boiler of a two boiler ship?
- 472.If the fires to a steaming boiler have been accidentally extinguished, you should not relight any burner until __________.
- 473.During the operation of a lube oil centrifuge, a thin emulsion interface occurs between the lube oil and seal. The position of this interface is determined by the __________.
- 474.Which of the condensers listed is cooled by sea water?
- 475.Which of the following statements is true concerning lube oil coolers?
- 476.A higher than normal stack gas temperature could indicate __________.
- 477.The original bridge gage reading for a reduction gear bearing was measured as .008 inches. A year later, the bridge gage reading for the same bearing is .010 inches. This indicates __________.
- 478.The steam drum air cock is normally opened when cooling down a boiler to __________.
- 479.In order to obtain the best performance with a lube oil purifier, the lube oil inlet temperature should __________.
- 480.Chamfers, located at the parting edges of horizontal split sleeve type bearings, are used to facilitate oil storage and distribution. They are machined __________.
- 481.After the steam leaves the low pressure turbine, it enters the __________.
- 482.To allow for water drum expansion and contraction, most main propulsion boilers are fitted with __________.
- 483.If the stack temperature is higher than normal, this could indicate __________.
- 484.In a marine boiler, maximum heat transfer rates can be obtained by __________.
- 485.The jacking gear must be engaged as quickly as possible when securing the main turbines in order to __________.
- 486.After a boiler has been taken off the line and is cooling, the air cock is opened to __________.
- 487.Which of the following conditions is true concerning the boiler water drum foundations?
- 488.The maximum lube oil temperature leaving the lube oil cooler of a main steam turbine propulsion system should __________.
- 489.Proper vacuum must be maintained in the main condenser to __________.
- 490.Which of the types of superheaters listed has the flattest superheat temperature curve?
- 491.Chemicals are added to boiler water in order to __________.
- 492.Before lighting any burner in a cold boiler you should always __________.
- 493.The main propulsion turbine should be operated with the __________.
- 494.The internal feed pipe in a D-type marine boiler __________.
- 495.Burning fuel with entrained saltwater, will cause a glassy slag formation on furnace refractory. This slag will __________.
- 496.While underway, vacuum in the main condenser is primarily caused by the __________.
- 497.The dirty oil inlet on centrifugal lube oil purifiers is located at the __________.
- 498.Boiler stack gas temperatures will be higher than normal when __________.
- 499.What is the quickest way to shutoff the boiler fuel oil supply from inside the fire room?
- 500.Chemicals are added to boiler water to __________.