USCG Steam Plants – Question Bank Book 13 (BK13) — page 4
1769 questions with correct answers from the official USCG question bank (2008 edition), book 13 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 301.To minimize axial thrust in an impulse turbine, equalizing holes are located __________.
- 302.If the low water level alarm sounds on an automatically fired boiler, and the low water cutout fails to function, you must immediately __________.
- 303.Combustion control systems on automatic boilers are designed to prevent immediate burner ignition after a normal or safety shutdown in order to allow time for __________.
- 304.If it is necessary to operate a turbine driven main feed pump at shut off head, or at less than 20% of its rated capacity, what will prevent the pump from overheating?
- 305.Discharging an excessive amount of cold water into the DC heater during normal steaming conditions could cause __________.
- 306.The turndown ratio an automatic combustion control system is the ratio __________.
- 307.In a properly designed boiler, which of the end points should be reached first?
- 308.To obtain the best mixing of air and fuel with a fuel oil atomizer, you need to adjust the __________.
- 309.Dissolved oxygen can be removed from the boiler water by __________.
- 310.Which of the following statements is true concerning a photocell flame scanning system?
- 311.When a turbine is in operation, a rotor position micrometer is used to determine any change in rotor __________.
- 312.How is the nozzle in a nozzle reaction safety valve held in place?
- 313.If the control air pressure for an automatic combustion control system is lost during maneuvering, you should immediately __________.
- 314.A turbine-driven centrifugal feed pump used for boiler feed service should normally be stopped by __________.
- 315.In addition to monitoring flame quality, flame scanners are used in combustion control systems to __________.
- 316.In a properly designed boiler, which end point is most likely to occur first?
- 317.Fuel oil passing through the burners is divided into fine particles by the __________.
- 318.If an automatically fired burner ignites, but repeatedly goes out within two seconds, the cause could be a/an __________.
- 319.On a boiler safety valve, the blow down adjusting ring is locked in place by a __________.
- 320.Flame scanners are used with boiler combustion control systems to monitor flame quality and to __________.
- 321.Fuel oil settling tanks are used to __________.
- 322.Ultraviolet light sensing flame scanners installed on an automated main propulsion boiler, are designed so they __________.
- 323.Which of the boiler end points should be reached first?
- 324.The amount of oil atomized by a straight mechanical fuel oil burner depends on the sprayer plate size and the __________.
- 325.What are the two most common gases that dissolve in boiler water and cause corrosion on the internal parts of the boiler?
- 326.Which of the following represents a significant system limitation to be aware of when a burner management system is operated in the 'HAND' mode?
- 327.What happens to the steam as it moves across the moving blades in a reaction turbine?
- 328.An advantage of using boiler furnace studded water wall tubes packed with refractory is that __________.
- 329.If the water level in the boiler water gage glass is not in sight, and the automatic feed water regulator is in the closed position, the __________.
- 330.Which of the following systems is designed to use auxiliary exhaust steam?
- 331.During cold ship start-up, you should open the feed water outlet and condensate valves to a DC heater in order to __________.
- 332.In a boiler automation system, if a burner fuel oil solenoid valve continually trips closed under normal steaming conditions, you should __________.
- 333.The 'end point for combustion' for a boiler furnace is reached whenever __________.
- 334.While your vessel is steaming with one boiler, the automatic combustion control system sensing line for the idle boiler is accidentally opened. How will this effect the steaming boiler?
- 335.Packing rings installed on auxiliary turbines are generally lubricated by __________.
- 336.When the automatic combustion control fails, what should you do to control the air supply to a boiler?
- 337.When conducting a routine hydrostatic test on a water-tube boiler, you should __________.
- 338.Under normal operating conditions, a drop in the steam temperature leaving an uncontrolled interdeck superheater could be caused by a __________.
- 339.If the boiler water and condenser hotwell levels are normal, but the DC heater level is only 30% of full, you should __________.
- 340.Auxiliary exhaust steam can generally be used as a supply for the __________.
- 341.Reaching which of the boiler end points listed could cause the most damage to a boiler?
- 342.High salinity can be reduced in a steaming boiler by adding caustic soda, phosphate, and then __________.
- 343.Which of the following systems can normally be supplied by auxiliary exhaust steam?
- 344.Under normal conditions, the rate of heat transfer in a feed water heater is most greatly affected by the __________.
- 345.Which set of boiler end points listed is considered to be the normal order of occurrence?
- 346.Which of the listed characteristics of fuel oil establishes the danger point as far as transferring, pumping, and firing procedures are concerned?
- 347.Which of the terms listed represents the ratio between the highest and lowest fuel oil pressure at which the burners will remain ignited?
- 348.If a routine boiler water test indicates high salinity, you should blow down the boiler to reduce salinity and then __________.
- 349.The steam soot blower piping should be thoroughly drained before operating to prevent __________.
- 350.In a cross-compounded turbine operating at full load, the total available steam energy is approximately divided between the HP and LP turbine in the ratio of __________.
- 351.The turbo generator steam stop is located between the superheater outlet and the main steam stop valve to __________.
- 352.An increase in the pressure drop between the inlet and outlet of the feed water heater waterside, not due to a waterside obstruction, would indicate __________.
- 353.Which of the drains listed could be led directly to a DC heater operating at 35 psig (343 kPa)?
- 354.Which of the following systems can be supplied by the auxiliary exhaust system?
- 355.Under normal operating conditions, a drop in the steam temperature leaving an interdeck-type superheater can be caused by a decrease in the velocity of the __________.
- 356.In addition to the repeated use of surface blow to control boiler water chemistry, caustic soda may be used to treat high salinity, as well as __________.
- 357.Upon taking over the watch, while the vessel is at sea speed, you find the following conditions to exist. Which condition should be attended to first and why should this step be taken?
- 358.A turbine assembly in which steam flows in series through a high pressure turbine and then on to a low pressure turbine, with both turbines driving a common reduction gear through separate shafts, is classified as _________.
- 359.The main steam stop valve on a "D" type marine boiler is located at the __________.
- 360.Dirty generating tube surfaces may cause higher than normal superheater outlet temperatures because __________.
- 361.If there is a sudden drop in the outlet temperature of an uncontrolled superheater, you should __________.
- 362.In a modern high pressure steam plant, most feed water deaeration takes place in the __________.
- 363.The limiting factor in determining the end point for combustion is usually the __________.
- 364.Improper atomization can be caused by __________.
- 365.In a steaming boiler most dissolved chlorides tend to concentrate at or near the __________.
- 366.In an impulse turbine, the fixed blades function to __________.
- 367.The main steam stop bypass valve is used to __________.
- 368.Under normal conditions, steam to the DC heater is supplied directly from which of the systems listed?
- 369.Insufficient combustion air supply to the furnace would cause __________.
- 370.The designed function of fixed blades in an impulse turbine is to __________.
- 371.The bottom blow valve on a water-tube boiler is usually attached to the __________.
- 372.Insufficient combustion air supply to a boiler furnace can cause __________.
- 373.A burner atomizer improperly positioned in the distance piece, may cause __________.
- 374.Calcium minerals in boiler water are precipitated out of solution by the use of which of the listed chemicals?
- 375.A boiler internal feed pipe is perforated to __________.
- 376.Gland sealing steam is used on propulsion turbines to prevent __________.
- 377.Boiler fuel savings gained by the use of an economizer can amount to __________.
- 378.A photoelectric cell is installed in an oil fired boiler safeguard system to introduce proper resistance values to the electronic control circuit. This device is primarily sensitive to __________.
- 379.Treatment of boiler feed water for the control of hardness is necessary to prevent __________.
- 380.In a DC heater, which source of steam is commonly used to heat and deaerate condensate?
- 381.Low steam pressure in a steaming boiler can be caused by __________.
- 382.Which of the following boiler stack (smoke color) conditions indicates efficient combustion?
- 383.If the boiler water level of one boiler drops out of sight while your vessel is steaming, and the burners have been secured, you should __________.
- 384.When a high pressure turbine is operating at sea speed, the pressure of the steam leaking through the shaft gland packing may be slightly higher than the pressure setting of the gland seal regulator. In this situation, the excess steam at the regulator is directed to the __________.
- 385.The phrase 'boiler water column' as defined in the regulations, refers to the __________.
- 386.Which of the following statements best describes the actions occurring to the oil as it flows through a disk type centrifugal purifier?
- 387.Dissolved oxygen in the condensate can result from __________.
- 388.Coast Guard Regulations (46 CFR) permit repairs and adjustments to boiler safety valves while installed on a main propulsion boiler and may be made by ________.
- 389.If a burner were inserted too far into the boiler furnace, it could cause carbon deposits on the __________.
- 390.To minimize metal corrosion, boiler water is best kept __________.
- 391.In a disk type centrifugal purifier, the bowl is mounted on the upper end of the __________.
- 392.A centrifuge should satisfactorily remove which of the listed substances from lube oil?
- 393.Which of the following statements represents the function of a turbine gland exhaust condenser?
- 394.Coast Guard regulations require that the relieving capacity of boiler safety valves must be checked __________.
- 395.Insufficient air for combustion in a boiler furnace could result in a __________.
- 396.Which of the following represents the function of the diffuser used with a mechanical atomizing oil burner?
- 397.A sulfite test is conducted on boiler water to check for __________.
- 398.One function of the disks, in a disk-type centrifugal purifier, is to divide the bowl space into many separate passages to __________.
- 399.The main propulsion shaft turning gear usually connects to the free end of the high-speed high pressure pinion because the __________.
- 400.A boiler feed stop-valve must be mounted __________.