USCG Steam Plants – Question Bank Book 13 (BK13) — page 3
1769 questions with correct answers from the official USCG question bank (2008 edition), book 13 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 201.Excessive water flow beyond the design limits of a feed water heater, will be indicated by a/an __________.
- 202.A two-element boiler feed water regulator is controlled by __________.
- 203.A high water level in a deaerating feed heater will cause the automatic dump valve to drain condensate to the __________.
- 204.As steam accomplishes work in an engine or turbine, the pressure of the steam is reduced because it __________.
- 205.The greatest single overall loss of efficiency in a marine propulsion steam plant cycle results from __________.
- 206.The most serious fireside burning of the boiler superheater tubes is the result of __________.
- 207.If the theoretical quantity of dry air required to burn one pound of fuel oil is 13.75 pounds, what weight of air will be necessary to burn one pound of fuel to operate a boiler at 10% excess air?
- 208.As steam accomplishes work in an engine or turbine, it expands and __________.
- 209.The purpose of the division plates installed in boiler superheater headers is to __________.
- 210.A two-element feed water regulator responds directly to changes in __________.
- 211.The DC heater automatic level dump valve is used to __________.
- 212.Which of the following conditions in a water-tube boiler generating tube could cause tube failure, even if the water gage glass shows the proper level?
- 213.Efficient combustion in a boiler is indicated by a __________.
- 214.When seated, the disc of a safety valve has an area of 0.75 square inches (1.9 sq cm). When the valve lifts the area is increased by 10%. If the valve lifts at 300 psig (2170 kPa), at approximately what pressure will the valve reseat?
- 215.When a boiler water test indicates a pH value of 6, you should __________.
- 216.In a D-type boiler, which of the tubes listed would be located in the generating tube bank?
- 217.If water hammer develops while opening the valve in a steam line, which of the following actions should be taken?
- 218.Two-element feed water regulators operate by sensing __________.
- 219.High pressure steam drains are normally discharged to the __________.
- 220.The major heat loss in an oil fired boiler is the heat __________.
- 221.When securing a boiler, the burner registers are to be left open for a few minutes to __________.
- 222.In modern reaction turbines, thin tipping is a procedure designed to __________.
- 223.Boiler screen tubes are used to protect which of the listed components from high furnace temperature?
- 224.The best conductor of heat in a marine boiler is __________.
- 225.A two-element feed water regulator reacts to changes in the steam drum water level and the __________.
- 226.Damage to deck machinery from water hammer developing in the steam lines can be prevented by __________.
- 227.If the theoretical quantity of dry air required to burn one pound of fuel oil is 13.75 pounds, what is the weight of air per pound of fuel when operating a boiler at 5% excess air?
- 228.The boiler fuel oil system 'hot' strainers are also known as __________.
- 229.Turbine casing flanges are sometimes provided with a system of joint grooving to __________.
- 230.A convection type superheater in a D-type boiler is protected from radiant heat by __________.
- 231.One of the operating conditions sensed by a two-element feed water regulator is __________.
- 232.In the boiler steam and water system, pressure is highest in the __________.
- 233.If the theoretical quantity of dry air required to burn one pound of fuel oil is 13.75 pounds, what will be the weight of the air necessary to burn one pound of fuel when operating a boiler at 15% excess air?
- 234.The boiler fuel oil system suction strainers are also known as the __________.
- 235.On an automatically fired boiler, the loss of forced draft fan will result in which of the listed actions to be carried out?
- 236.A boiler superheater support tube differs from a standard generating tube in that the __________.
- 237.Scavenging air is supplied to steam soot blowers to __________.
- 238.A two-element feed water regulator not only responds to changes in water level, but is also designed to react to __________.
- 239.The leakage of air into the pump casing by way of the packing gland of a condensate pump, is prevented by __________.
- 240.If the theoretical quantity of dry air required to burn one pound of fuel oil is 13.75 pounds, what will be the weight of the air necessary to burn one pound of fuel to operate a boiler at 20% excess air?
- 241.Strainers are installed in boiler fuel oil service lines to __________.
- 242.Under constant boiler load, the superheated steam temperature may rise above normal for the existing load if __________.
- 243.A turbine diaphragm functions to __________.
- 244.Which of the methods listed would be most effective in repairing a steam cut on a seating surface of a superheater handhole plate?
- 245.The concentration of total dissolved solids in boiler water could increase as a result of __________.
- 246.Which type of feed water regulator listed provides the MOST effective regulation of boiler water level under all operating conditions?
- 247.Flooding of the DC heater, due to the addition of excessive makeup feed, is normally corrected by the use of __________.
- 248.Excess air must be provided to an operating boiler to allow for __________.
- 249.Strainers are installed in boiler fuel oil service lines to __________.
- 250.A boiler with a water capacity of 10 tons, generates steam at the rate of 30 tons per hour. If the feed water quality is 0.5 ppm, the concentration of solids will increase 1.5 ppm every hour. What would be the increase in the concentration of solids w
- 251.Air accumulated in the after condenser of the air ejector unit is discharged directly to the __________.
- 252.In a boiler water gage glass, a ball check valve is installed on the __________.
- 253.Should the superheater outlet thermometer indicate an excessively high temperature on a single furnace boiler, the cause could be __________.
- 254.In an automatically fired boiler, the steam pressure regulator controls the supply of fuel oil to the burners by responding to variations in the __________.
- 255.Vent condensers are usually an integral part of deaerating feed heaters and serve to condense __________.
- 256.Too much excess air in a steaming boiler may be indicated by __________.
- 257.The concentration of total dissolved solids in the boiler water can increase as a result of __________.
- 258.The greatest deterrent to heat transfer from the fireside to the waterside of a boiler is __________.
- 259.For a large main propulsion turbine, the most commonly used turbine thrust bearing is the __________.
- 260.The minimum feed water inlet temperature to a boiler economizer is determined by the __________.
- 261.In automated boiler operations, a dirty flame scanner will most likely result in __________.
- 262.The two-element feed water regulator functions similarly to the three-element feed water regulator, but does not utilize __________.
- 263.The purpose of the re-circulating line between the turbine driven feed pump and the DC heater is to __________.
- 264.If a quantity of saturated steam consists of 90 percent steam and 10 percent moisture, the quality of the mixture is __________.
- 265.When too much excess air is supplied to an operating boiler, the __________.
- 266.Which of the listed types of strainers are installed between the fuel oil heater and the burner manifold?
- 267.Dissolved and suspended solids in boiler water are kept at minimum levels by __________.
- 268.Which of the listed devices may trip due to total flame failure in both boilers of an automated plant?
- 269.Bi-color water level indicators, connected directly to the boiler drum, operate on the principle of __________.
- 270.The difference between the temperature of the condensate discharge and the temperature corresponding to the vacuum being maintained at the exhaust inlet to the main condenser is defined as __________.
- 271.If the bellows in a thermo-hydraulic feed water control valve ruptures, the boiler water level will __________.
- 272.Feed water heaters are used aboard steam vessels to reduce thermal shock to the boiler and to __________.
- 273.As the percentage of CO2 in the stack gas decreases, you can assume that __________.
- 274.The valve located between the fuel oil header and the burner valve is known as the __________.
- 275.The end product of reactions occurring when boiler water is chemically treated, remain in the boiler and increase the need for __________.
- 276.Why is superheated steam used in the main propulsion turbines instead of saturated steam?
- 277.Reduction gear bearing bridge gage readings should be taken after __________.
- 278.The purpose of the mica used in a boiler water gage glass assembly is to prevent __________.
- 279.When the flame scanner senses flame failure during boiler operation, which of the listed events will occur FIRST?
- 280.Improper boiler feed water deaeration could be directly linked to __________.
- 281.In a closed feed water system, the greatest deaeration of condensate occurs in the __________.
- 282.Most marine boilers are designed to produce __________.
- 283.Excessive combustion air in a boiler is indicated by the flame ends appearing as a/an __________.
- 284.Fuel oil atomizers are used in boilers to __________.
- 285.A continuous blow is used to __________.
- 286.Which of the following statements is correct regarding axial thrust in a high pressure velocity-compounded turbine?
- 287.Where is the 'dry pipe' located in a boiler?
- 288.The weight of saturated steam is a factor dependent upon its __________.
- 289.The pressure in the feed water system must exceed boiler steam drum pressure in order to __________.
- 290.Feed water is deaerated to prevent __________.
- 291.Steam line water hammer can be best prevented by __________.
- 292.White smoke coming from the stack of a main propulsion boiler indicates __________.
- 293.In a marine boiler equipped with mechanically atomized burner assemblies, proper combustion depends on the __________.
- 294.The photoelectric cell installed as part of the combustion safety controls of an automatically fired boiler will __________.
- 295.The glass used in a flat-type boiler water gage is protected from the hot steam and water by a/an __________.
- 296.In a given weight of steam, four-fifths is vapor and one-fifth is moisture. The steam in this mixture is best described as __________.
- 297.Increasing the temperature of the feed water entering the steam drum will ultimately result in a/an __________.
- 298.Condensate is pumped from the condenser to the DC heater instead of directly to the boiler because __________.
- 299.In what section of a boiler would you find a steam quality of 90%?
- 300.Fuel oil viscosity to the atomizer can be reduced by __________.