USCG Steam Plants – Question Bank Book 13 (BK13) — page 16
1769 questions with correct answers from the official USCG question bank (2008 edition), book 13 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1501.The automatic re-circulating valve in the main condensate re-circulating line is controlled by a temperature sensor which is located at the __________.
- 1502.Automatic fuel shutoff to the burners of a main propulsion boiler could result from __________.
- 1503.A gravity type lube oil system for a steam vessel will have a remote pressure sensing device installed on the main lube oil header of the main turbine unit to enable the watch engineer to __________. I. determine if there is a normal level of lube oil in the gravity tank II. be certain that the bearings are being adequately lubricated
- 1504.What type of strainer is used in a turbine lube oil system to remove metallic particles?
- 1505.A turbo-generator governing system maintains constant turbine speed by using a flyweight-actuated pilot valve to control hydraulic oil flow to a lifting beam operating cylinder, which in turn, __________.
- 1506.While standing watch underway at sea, you notice salinity carryover in the low pressure distilling plant. This can be a result of __________.
- 1507.The most serious fireside burning of the boiler superheater tubes can be INDIRECTLY attributed to __________.
- 1508.High pressure and low pressure drain systems are part of the __________.
- 1509.Which of the operating principles listed would apply to a single-element, thermo-hydraulic, feed water regulator?
- 1510.The function of a quill shaft used on a double reduction gear main propulsion unit is to __________.
- 1511.The labyrinth seals used on rotating steam turbine shafts reduces external leakage by causing __________.
- 1512.Why are geared turbine installations equipped with turning mechanisms?
- 1513.According to 46 CFR Part 56, which of the following statements is true concerning the main steam stop valves on multiple boiler installations incorporating uncontrolled superheaters?
- 1514.To prevent damage to the turning gear mechanism, which of the following procedures must be carried out before the turning gear is engaged?
- 1515.If two turbo-generators with the same no-load speed settings are operating in parallel, the unit whose governor has the lesser speed droop will __________.
- 1516.Water circulates within a natural circulation boiler as a result of the __________.
- 1517.Which of the devices listed is generally used to engage the main engine turning gear to the high pressure turbine high-speed pinion?
- 1518.Main steam turbine lubricating oil systems are fitted with __________.
- 1519.Water circulates in a natural circulation boiler due to the __________.
- 1520.In which type of turbine does the steam pass through reversing chambers machined on the inner surface of the casing, causing the steam to be redirected back to the turbine wheel rim?
- 1521.The proportion of downcomers installed in relation to riser tubes in a vertical tube type of boiler, is dependent upon the __________.
- 1522.A steam driven 750 KW turbo generator has a rated speed of 1200 RPM. The over speed setting for this unit must not exceed __________.
- 1523.Which of the following precautions should be taken prior to lighting off a boiler?
- 1524.Constant speed governors are normally employed with __________.
- 1525.The steady frequency required from a ship service generator for electrical power is maintained by means of a __________.
- 1526.On main turbine propulsion units, gear type flexible couplings are generally used between the __________.
- 1527.The primary purpose of screen tubes installed in a marine boiler is to __________.
- 1528.Which of the following problems can occur when an excessive number of water screen tubes are plugged?
- 1529.The adjustable spherically seated self-aligning bearing housings used in main turbines are provided with oil deflector rings. The function of these rings is to __________.
- 1530.Which of the listed components is used to protect the boiler superheater against the radiant heat of the furnace?
- 1531.In a modern main propulsion turbine installations, lube oil system strainers are usually located in the __________.
- 1532.In steam turbine main engine installations, how are the main reduction gear bearings identical to other radial bearings?
- 1533.Using a dry uncoated sounding rod or tape to measure the depth of water in a reserve feed water tank will __________.
- 1534.Which of the following types of bearings are used as line shaft bearings?
- 1535.Which of the devices listed are used to rigidly mount reduction gear bearings in their housings?
- 1536.The most likely result of water slugging in the steam supply to a ship service turbo generator is __________.
- 1537.Which of the conditions listed occurs when glassy slag, formed by the burning of fuel oil contaminated with salt water, melts and runs over the furnace wall?
- 1538.The splits located in the halves of main reduction gear bearings are aligned at an angle to the horizontal in order to resist __________.
- 1539.To properly sound a reserve feed water tank, you should use a/an__________.
- 1540.Which possible condition has occurred if a vacuum is present at the atmospheric drain tank vent while the vessel is underway?
- 1541.The level of the drain inspection tank continually decreases after steam is admitted to a double bottom tank fuel oil heating coil. You can expect __________.
- 1542.Which of the following statements describes the function of a ship's propulsion plant main reduction gear thrust bearing?
- 1543.Turbine lube oil suction strainer baskets have __________.
- 1544.Which of the following operational practices is helpful in avoiding the accumulation of condensate in the main reduction gear casing?
- 1545.Which of the bearings listed is used in some turbines to limit axial movement?
- 1546.The Kingsbury bearing is equipped with pivoted shoes in order to __________.
- 1547.Which of the features listed, regarding the Kingsbury thrust bearing, prevents the base ring from turning and secures it to its housing?
- 1548.In a reduction gear train, a quill shaft of high torsional flexibility provides __________.
- 1549.The steam drum in a D-type marine boiler __________.
- 1550.Which of the flexible coupling types listed is used in most turbine reduction gear installations?
- 1551.When two or more boilers provide steam flow to a common main steam line, each boiler main steam line shall be fitted with a main steam stop valve and a/an __________.
- 1552.Which of the following factors determines the type of construction used for gear hubs in shipboard reduction gear units?
- 1553.Which of the conditions listed could cause steam formation in the economizer?
- 1554.The phenomenon called 'shrink' causes an apparent drop in the water level of a steaming boiler. This phenomenon is caused by a/an __________.
- 1555.Fresh water accumulating in the reduction gear sump may be directly attributed to a/an __________.
- 1556.Before using a boiler compressed air soot blower system, you should __________.
- 1557.The pinion gears used in main propulsion reduction gear mechanisms are generally constructed of __________.
- 1558.Which of the listed conditions causes shrinkage in boiler water levels?
- 1559.In main propulsion systems, which metal is used in the construction of the shafts for a main reduction gear unit?
- 1560.The effects of shrink and swell on boiler water levels can be minimized by __________.
- 1561.Why are the gear teeth of large reduction gears usually cut in a temperature controlled room?
- 1562.The superheater vents should always be open when __________.
- 1563.The scavenging air for soot blowers is supplied by the __________.
- 1564.Which of the following represents one of the designed functions of reduction gears?
- 1565.When securing the main engine, which of the listed procedures should be carried out to remove or reduce condensation from the interior of the main reduction gear casing?
- 1566.In a gravity lube oil system, a sight glass is installed in a line near the operating platform. This line connects the __________.
- 1567.A Kingsbury, or pivot shoe type thrust bearing, can bear much greater loads per square inch of working surface than can parallel surface bearings because provisions are made in the Kingsbury bearing __________.
- 1568.If saltwater leaks into and contaminates the main lubricating oil system, which of the following remedial actions should be taken?
- 1569.Which of the following statements represents the principle of operation of the Kingsbury type thrust bearing?
- 1570.Which of the following statements represents the function of the center groove machined on a double-helical gear?
- 1571.As the rate of combustion is increased in a boiler, more steam is generated because the __________.
- 1572.By which of the following means can rotating parts of the main reduction gear be examined?
- 1573.When raising steam on a boiler, the superheater drains should __________.
- 1574.The maintenance of reduction gear units is principally concerned with attention to keeping the __________.
- 1575.After steam has been raised and a boiler is being placed on the line, the superheater vent can be closed when __________.
- 1576.Which immediate action should you take when the temperature of one line shaft bearing increases above its normal operating temperature?
- 1577.When a boiler is up to pressure and is being placed on the line, you should secure the __________.
- 1578.Which of the following problems is likely to occur if the lube oil level in the sump is too high?
- 1579.Sludge tanks are used in an oil lubricating system to receive __________.
- 1580.On a boiler equipped with an uncontrolled interdeck superheater, reducing the feed water temperature to the steam drum will cause the superheater outlet temperature to __________.
- 1581.In herringbone helical gear sets, the tooth contact loading __________.
- 1582.A cloudy or milky appearing lube oil sample, taken from the main lubricating oil system could be caused by __________.
- 1583.Reduction gears on main propulsion turbines are double helical cut to __________.
- 1584.The steam generating capacity of a boiler depends upon the __________.
- 1585.In a disk type lubricating oil centrifuge __________.
- 1586.Under otherwise normal steaming conditions, an abnormally high temperature at the superheater outlet of a single furnace boiler would indicate __________.
- 1587.Main reduction and pinion gears are double helically cut to __________.
- 1588.When answering a full astern bell from half ahead, the superheater outlet temperature on a single furnace boiler will __________.
- 1589.Lube oil temperature leaving the lube oil coolers is regulated by throttling the __________.
- 1590.In an automatically fired boiler, increasing the temperature of the feed water entering the steam drum will ultimately result in a/an __________.
- 1591.The purpose of the main reduction gears is to __________.
- 1592.If a tube should leak in an operating main steam turbine lube oil cooler, the water will not immediately contaminate the oil because the __________.
- 1593.An air vent is installed on some reduction gear casings to __________.
- 1594.During high speed operation of the main turbine propulsion unit, the heat absorbed by the lubricating oil is removed by the __________.
- 1595.Which of the following bearings is designed to take loads applied to the axis of the shaft?
- 1596.In some lube oil systems, the temperature of the lube oil downstream from the lube oil cooler is directly regulated by __________.
- 1597.When the temperature of the main turbine lubricating oil is lowered, an increase will occur in the __________.
- 1598.Thrust bearings are installed in main propulsion turbines to __________.
- 1599.To test an automatic low lube oil pressure trip on an idling turbo generator and at the same time prevent the chance of bearing damage, you should __________.
- 1600.In a steadily steaming boiler, carryover is indicated by a/an __________.