USCG Steam Plants – Question Bank Book 13 (BK13) — page 15
1769 questions with correct answers from the official USCG question bank (2008 edition), book 13 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1401.According to 46 CFR's, steam piping subject to main boiler pressure must be hydrostatically tested at specified intervals. Therefore, which of the following statements is true?
- 1402.Flexible couplings used between main turbine rotors and reduction gear installations are usually ________.
- 1403.What will be the FIRST thing to occur if both the main and standby lube oil pumps failed to operate on a geared main propulsion steam turbine operating at full sea speed?
- 1404.Which of the following locations could desuperheated steam be considered to occur?
- 1405.A vent line is provided on each water box of the main condenser in order to prevent __________.
- 1406.After the main engine has reached full sea speed, which of the following conditions could cause the water level in the boiler steam drum to keep falling?
- 1407.If the pressure becomes excessive in the auxiliary exhaust system of a steam propulsion plant, the excess steam will normally be dumped to the __________.
- 1408.Which of the following conditions must exist before the superheating of saturated steam can occur in a steam propulsion boiler?
- 1409.Excessive priming in a propulsion boiler can cause severe damage to the_________.
- 1410.The useful life of furnace refractory is affected most by __________.
- 1411.When heated, brickwork in a boiler is kept from buckling by the installation of __________.
- 1412.From which of the areas listed are condensate drains normally collected and returned to the atmospheric pressure drain system?
- 1413.Which of the following statements is true concerning the use of hydrazine in boiler water treatment?
- 1414.Which of the following statements represents the significance of the differential pressure existing between the nozzle block and steam chest of a turbo generator equipped with a lifting beam mechanism?
- 1415.If a line shaft bearing begins to overheat, the shaft speed should be reduced. If overheating persists, you should then __________.
- 1416.Which of the following types of bearings is designed to limit end movement and carry loads applied in the same direction as the shaft axis?
- 1417.How are line shaft bearings usually lubricated?
- 1418.High boiler water level can cause carryover and __________.
- 1419.When preparing to light off a cold boiler, the fuel oil should be re-circulated until it is __________.
- 1420.A sample of boiler water can be chemically tested for alkalinity by initially adding a few drops of phenolphthalein and then slowly titrating the water sample until the __________.
- 1421.High pressure steam drains from systems operating at above 150 psi are normally collected in the __________.
- 1422.Under normal operating conditions of constant load and combustion rates, which of the following will occur when the amount of excess air to the furnace is increased?
- 1423.Where reaction turbine blading is fitted with shrouding of "end tightened" design, which of the following conditions will be the most critical to efficient turbine operation?
- 1424.Before placing the jacking gear in operation on a main turbine unit, you must always insure that __________.
- 1425.On an fully automated vessel steaming at sea speed, which of the following engine room responses will automatically be actuated when the bridge throttle control is changed from full ahead to slow ahead?
- 1426.Which condition would cause a high level in the deaerating feed water tank (DC heater)?
- 1427.After properly lining up the main propulsion turbine for warm up, steam should first be admitted to the rotor through the __________.
- 1428.Which combustible element in fuel oil is considered a significant and major source of air pollution?
- 1429.Improper fuel oil burner atomization can be generally attributed to __________.
- 1430.White stack smoke from a main propulsion boiler could indicate __________.
- 1431.In a closed steam and water cycle, which of the conditions listed could prevent main condenser vacuum from reaching the desired level?
- 1432.The property of a fuel oil which is a measurement of its available energy, is known as its __________.
- 1433.Fine metallic particles, which may originate from wear or failure of the lube oil service pump internal parts, are prevented from contaminating the bearings served by the lube oil system by __________.
- 1434.Fuel oil is transferred from storage tanks to the settling tanks to allow for __________.
- 1435.Fuel oil accumulation in a boiler double front is generally caused by __________.
- 1436.According to 46 CFR Parts 59 and 35, which of the following is true?
- 1437.In order to operate the main engine with only the high pressure turbine in service, the unit should be arranged __________.
- 1438.You are standing a sea watch in the engine room of a steam vessel. To operate at maximum efficiency, adjustments to the boiler combustion control system should be made by setting the __________.
- 1439.While standing watch in the engine room, you suspect air leaking into a flash type distilling plant. The most probable cause(s) of the air leak could occur through __________.
- 1440.In a double reduction gear, the function of a quill shaft is to provide flexibility between the second reduction pinion and the __________.
- 1441.The labyrinth packing ring in an interstage diaphragm of an impulse turbine is prevented from rotating by __________.
- 1442.Boiler refractories previously baked out and fired are most sensitive to __________.
- 1443.Boiler water samples should be circulated through a cooling coil prior to analysis because __________.
- 1444.Which system should be used when required to raise the water level in an idle boiler?
- 1445.Which statement is true concerning two-stage air ejector assemblies?
- 1446.Auxiliary steam at full operating pressure is supplied from the boiler directly to the __________.
- 1447.The primary function of the contaminated drain inspection tank is to __________.
- 1448.One of the most effective methods of improving purification in tubular and disk type centrifugal purifiers is to __________.
- 1449.The internal feed pipe of a power boiler distributes the feed water into the __________.
- 1450.Cooling water to the vent condenser in a DC heater is supplied by the __________.
- 1451.Ferrous sulfate tends to go into solution in boiler water when the value of the hydrogen ion concentration increases. Consequently, the water in a 900 psi boiler should be __________.
- 1452.Chemicals are added to boiler feed water to __________.
- 1453.In a boiler furnace, incomplete combustion due to insufficient air yields an excess amount of __________.
- 1454.In order to test the lifting pressure of the deaerating feed heater relief valve, you would __________. I. close the auxiliary exhaust dump valves to the main and auxiliary condenser II. increase the set point of the reduced steam pressure to the aux
- 1455.Which of the following actions should be taken FIRST when the boiler fires begin to sputter due to water in the fuel oil?
- 1456.While making engine room rounds at sea, you observe excessive steam leaking from the forward gland on the high pressure turbine. This may indicate that the __________.
- 1457.Which of the devices listed is used to convert thermal energy to useful mechanical work?
- 1458.Carbon ring packing segments are secured in a shaft gland assembly of a steam turbo generator by means of __________.
- 1459.Labyrinth packing rings are installed on turbine diaphragms to minimize __________.
- 1460.Steam passing through a multistage impulse turbine does not impart any appreciable axial thrust to the rotor. This is primarily due to the __________.
- 1461.Of the many impurities commonly found in marine lubricating oil, which of the following CANNOT be removed by a centrifugal purifier at normal operating speeds and temperatures?
- 1462.The factor which determines the minimum amount of steam superheat required at the steam chest inlet of a main propulsion turbine is the __________.
- 1463.When preparing to get underway and the jacking gear has been disengaged, the main turbine rotor should NOT be allowed to remain stationary for more than 3 minutes because __________.
- 1464.A rotor position micrometer on a main propulsion reaction turbine measures rotor __________.
- 1465.Operating a steam turbine propulsion unit at reduced speed, in an area with extremely cold seawater, with the main circulating pump providing full cooling water flow to the condenser will result in __________.
- 1466.Which of the following statements defines the term 'axial float' in reference to reduction gears?
- 1467.Coast Guard Regulations (46 CFR Part 52) concerning boiler superheater safety valves require that the valve __________.
- 1468.If a main lube oil pump fails to build up discharge pressure, the cause could be the __________.
- 1469.Which of the devices listed is commonly used to compensate for the expansion and minor misalignments occurring between the main turbine rotor and the reduction gear?
- 1470.One cause for unusually low lube oil service pump pressure may be due to __________.
- 1471.The main turbine gland sealing system is designed to __________.
- 1472.Regarding main propulsion boilers, what condition would normally be indicated if the bridge reported that white smoke was observed coming from the stack?
- 1473.Which of the following is used to hold the poppet valves closed in a turbo generators nozzle control speed regulator?
- 1474.The safety device provided on a turbo generator which closes the throttle automatically when the cooling water to the condenser is insufficient is called a/an __________.
- 1475.When starting a turbo generator in an automated plant, you must provide external lube oil pressure to the unit for the purpose of __________.
- 1476.The three-wing device used in the tubular bowl purifier, is held in place and forced to rotate at bowl speed by the __________.
- 1477.The over speed tripping device installed on an auxiliary turbine is automatically actuated by __________.
- 1478.The absence of carbon monoxide in the flue gas of a boiler indicates __________.
- 1479.A centrifugal oil purifier should be shut down if the __________.
- 1480.When preparing to cut a boiler in on the line, you determine that the steam pressure of the incoming boiler is about 5 psig above line pressure. Which of the following steps should you take next?
- 1481.The greatest heat loss in an oil fired boiler is from __________.
- 1482.If one fuel strainer of a duplex strainer unit becomes clogged while your vessel is underway, you should first __________.
- 1483.In a multistage reaction turbine, the dummy piston and cylinder function to __________.
- 1484.The term 'separation' as used in oil purification refers to the removal of __________.
- 1485.The valve opening sequence for bar-lift nozzle control valves in a marine steam turbine is determined by __________.
- 1486.The proper way to quickly reduce high water level in a steaming boiler is to use the __________.
- 1487.Upon taking over the watch and the vessel is operating at sea speed, you find the D.C. heater water level to be dropping very slowly. Which of the following would you check to monitor this condition?
- 1488.Upon assuming the watch on a steam ship while cargo operations are in progress with the main engine and reduction gear secured, you notice a very large increase in the reduction gear lube oil sump level from previous log book entries. What would be the most probable cause of this large increase in sump level?
- 1489.If the rated distillate production of a submerged tube type evaporator cannot be maintained with the supplied maximum steam pressure, the evaporator __________.
- 1490.Moisture erosion in the last stages of the low pressure turbine will result from __________.
- 1491.Water carryover in the steam entering a turbine could result in __________.
- 1492.An auxiliary turbine boiler feed pump should normally be stopped by __________.
- 1493.A back pressure trip on an auxiliary turbo-generator functions to secure the device if the __________.
- 1494.One method of securing shroud bands are secured to the ends of the turbine blades is to __________.
- 1495.The general method of fastening should bands to turbine blades would be to use __________.
- 1496.The general method of reducing turbine reaction blade vibration is by the use of __________.
- 1497.What is generally found at the end of the low pressure turbine rotor of a cross compound turbine arrangement?
- 1498.Why do double flow reaction turbines produce very little axial thrust?
- 1499.Which of the following lube oil system lines generally includes an illuminated sight glass (bull's-eye)?
- 1500.If a spring bearing begins to run at an abnormally high temperature, you should __________.