USCG Steam Plants – Question Bank Book 13 (BK13) — page 8
1769 questions with correct answers from the official USCG question bank (2008 edition), book 13 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 701.The formation of a pit in a boiler tube is most likely to occur when __________.
- 702.Blowing down a water wall header while steaming a boiler at a high firing rate could result in __________.
- 703.Electrolytic corrosion in the condenser circulating water system can be reduced by __________.
- 704.Which condition would cause a dangerously low level in the deaerating feed water tank (Direct Contact) heater during maneuvering?
- 705.Dissolved oxygen entrained in the feed water entering a boiler can cause __________.
- 706.The differential temperature of the main condenser circulating water will be affected by __________. I. decrease in circulating pump pressure II. degree or amount of scaling or fouling
- 707.Under what operating conditions may water wall header drains be used for blow down?
- 708.A water-tube type boiler when compared to a fire-tube type boiler has an advantage of __________. I. a water-tube boiler requiring less chemical compounding II. the fire-tube boiler providing a greater amount of heat transfer to the water as the hot
- 709.Vapor blowing from the air ejector condenser vent may be caused by __________.
- 710.When burning fuel oil in a boiler, a high CO2 content is desired in the stack gas because __________.
- 711.When re-circulating fuel oil prior to cold boiler start-up, which of the listed actions should be carried out?
- 712.Babbitt is a metal alloy commonly used for lining __________.
- 713.Machinery operating features are designed to help conserve energy. Which of the following will not contribute to energy conservation?
- 714.Prior to rolling the main turbines in preparation for getting underway, you should __________.
- 715.Advances in metallurgy and improved methods of boiler tube fabrication has led to lighter tubes with wall thicknesses in the vicinity of 0.1 inches. A characteristic of these thin walled tubes is __________.
- 716.A steam supplied heat exchanger will fail to maintain the designed quantity of heated liquid output if the __________. I. steam side shell absolute pressure is decreased II. heat exchanger drain is leaking
- 717.Which condition would cause an excessively high level in the deaerating feed water tank (DC heater)?
- 718.Scale in the air ejector first-stage nozzle could cause a decrease in the __________.
- 719.A flue gas air heater, when installed in a boiler would be accompanied by the operating characteristic(s) of __________. I. higher uptake temperatures than a boiler without an air heater II. lower corrosion rates in the uptakes and economizer
- 720.In a water-tube boiler, waterside scale formation is caused by __________.
- 721.Excessive priming in a propulsion boiler can cause severe damage to the_________. I. integral superheater II. main steam turbine
- 722.Which of the following problems can occur from improper main turbine warm-up?
- 723.If it becomes necessary to remove water from a pressurized main boiler, it should be directed __________.
- 724.Which condition would cause a dangerously low level in the deaerating feed water tank (Direct Contact) heater as the vessel is increasing from maneuvering to sea speed?
- 725.Excessive priming in a propulsion boiler can lead to severe damage of the __________. I. downcomers installed in a "D" type boiler II. main steam turbine reduction gears
- 726.Insufficient cooling water circulation through air ejector inter-condensers and after-condensers will cause __________.
- 727.The first and second stage air ejectors used with large sea water cooled steam, surface type condensers are designed to __________. I. establish vacuum II. maintain vacuum
- 728.An explosion or flareback could occur in a boiler if __________.
- 729.Boiler downcomers serve the purpose of __________. I. distributing water within the water or mud drum II. increasing the end point of carry-over
- 730.Boiler water hardness is increased by __________.
- 731.A badly warped boiler water tube can be reworked and bent back into shape by __________. I. heating it with a torch and reforming it with a soft mallet II. cold pressing it back into shape with a hydraulic jack
- 732.Turbine throttling losses can best be described as a loss of energy occurring __________.
- 733.Which of the following statements represents the advantage of using a small diameter boiler tube over a larger diameter tube?
- 734.The steam drum installed in "D" type boilers serve to provide __________. I. a water reserve necessary for proper boiler operation II. an area for steam and moisture to separate
- 735.According to Coast Guard Regulations (46 CFR), periodic hydrostatic tests are required to be conducted without exception on all __________.
- 736.If the cooling water flow through the air ejector inter-condensers and after-condensers is inadequate, which of the problems listed will occur?
- 737.In order to test the lifting pressure of the deaerating feed heater relief valve, you would __________. I. place a gag on the relief valve II. increase the set point of the reduced steam pressure to the auxiliary steam system
- 738.Before an explosion can occur in a boiler furnace, there must be an accumulation of unburned fuel, sufficient air to form an explosive mixture, and a __________.
- 739.The vent line from the main condenser water boxes was not opened when the waterside was recharged. This would __________. I. lead to a build up of pressure on the tube sheet of greater than 40 psig. II. prevent the design vacuum from being attained under normal operating conditions at sea.
- 740.Scale formation on the waterside of boiler tubes, is generally produced by __________.
- 741.Which of the following statements represents an example of a throttling loss in a turbine?
- 742.Which condition would cause a dangerously low level in the deaerating feed water tank (Direct Contact) heater as the vessel is increasing from maneuvering to sea speed?
- 743.According to Coast Guard Regulations (46 CFR), what is the maximum time interval for hydrostatically testing boilers on a cargo vessel having water-tube boilers?
- 744.Excessively hot water returning to an atmospheric drain tank indicates __________.
- 745.An accumulation of slag build up on the boiler furnace floor will cause __________. I. peeling of furnace brickwork II. overheating of the furnace floor
- 746.The most troublesome corrosive substances in boiler water are oxygen and __________.
- 747.Throttling the burner air register of a lit burner could result in __________.
- 748.Failure to remove calcium and magnesium from feed water before it reaches the boiler can result in tube __________.
- 749.Which of the effects listed describes the changes in the velocity and pressure of the steam as it passes through a nozzle?
- 750.In a watertube boiler, circulation is developed by the difference in the __________. I. tube length and various diameters II. densities of the hot and cold water
- 751.A ruptured boiler tube should be removed by __________. I. splitting the remaining tube sections with a safety ripping chisel II. cutting out most of the tube and then allowing the remaining portion to disintegrate as the boiler is normally fired
- 752.The maximum allowable working pressure of a particular boiler is 1050 psig (7340 kPa). The hydrostatic test pressure to be used during the Coast Guard required quadrennial inspection will be __________.
- 753.Which of the conditions listed may be indicated by the lifting of the DC heater relief valve?
- 754.A set of first and second stage air ejectors are used with a large sea water cooled steam condenser. If the first stage air ejector is not in operation __________. I. vacuum can not be established II. maximum operating vacuum can not be maintained
- 755.Sediment in fuel oil will cause __________.
- 756.The distance piece in a boiler burner register assembly, provides for adjustment of the __________.
- 757.The vent line from the main condenser water boxes was not opened when the waterside was recharged. This would __________. I. lead to vapor binding of the main circulating pump II. contribute to a higher than normal condensate temperature entering
- 758.Which steam plant watch operating condition will require priority attention over the other situations listed?
- 759.Before giving a boiler a surface blow, you should __________.
- 760.Coast Guard Regulations (46 CFR) require the duplex fuel oil discharge strainers installed in boiler fuel oil service systems to be __________.
- 761.If the DC heater relief valve lifts frequently, the cause can be excessive __________.
- 762.Sediment in fuel oil will cause __________.
- 763.Carbon dioxide dissolved in boiler water is dangerous in a modern power boiler because the gas __________.
- 764.A convergent-divergent nozzle functions to __________.
- 765.Before commencing a surface blow, the boiler __________.
- 766.The purpose of the boiler furnace corbel is to __________. I. protect the water drum from direct flame impingement II. support the furnace wall
- 767.Coast Guard Regulations (46 CFR) for boiler fuel oil service systems, require that __________.
- 768.In a boiler equipped with an automatic feed water regulator, erratic variations in the water level could be caused by __________.
- 769.A boiler water tube would burn out as a result of __________. I. direct flame impingement II. excessive soot accumulation
- 770.Boiler furnace brickwork can be fractured and broken by thermal shock caused by __________.
- 771.The two most common causes of boiler corrosion attributable to boiler water are dissolved oxygen and __________.
- 772.In addition to causing erosion of turbine blades, slugs of water in the steam supply to a turbine driven pump can result in __________.
- 773.Before giving a boiler a surface blow, you must __________.
- 774.According to Coast Guard Regulations (46 CFR), a 1200 psig maximum allowable working pressure boiler, with external blowoff piping is required to have the blowoff piping withstand a minimum of __________.
- 775.The depth of fuel oil in a double bottom tank is measured through the __________.
- 776.Why are the burner registers closed a few minutes after a boiler has been secured to be cooled?
- 777.In a boiler where the drum water level is automatically controlled, which of the following conditions could cause erratic variations in the water level?
- 778.Sliding contact bearings are classified into two general categories: journal bearings and __________.
- 779.When the rate of heat transfer through tube walls is so reduced that the metal becomes overheated, which of the following conditions will result in the boiler?
- 780.According to Coast Guard Regulations (46 CFR), blowoff piping external to a boiler with a maximum allowable working pressure of 600 psig must be capable of withstanding a minimum pressure of __________.
- 781.Saltwater contamination of condensate could occur at which component?
- 782.When you are transferring fuel oil to the settling tanks, precautions to be observed should include __________.
- 783.The main reason for keeping an operating boiler burner register fully open while steaming is to prevent __________.
- 784.In a steaming boiler, most dissolved chlorides tend to concentrate at, or near, the __________.
- 785.The turbine of a turbo-electric drive should be secured by __________.
- 786.In automatic combustion control systems, increasing or decreasing a loading pressure by a set amount is called __________.
- 787.A boiler desuperheater is installed in high pressure boilers to __________. I. maintain flow through the superheater II. raise the steam temperature in the steam drum
- 788.Once a huddling chamber type safety valve has begun to initially open, it will then pop open due to the __________. I. expansion of the steam leaving the nozzle II. forces exerted on the projecting lips
- 789.A common gas dissolved in water contributing to the greatest amount of corrosion in a condensate system is __________.
- 790.In a water tube boiler, waterwall tubes are effectively used to __________. I. decrease the amount of refractory material necessary in non-waterwall installations II. allow for significant increases in the combustion rates
- 791.Shortly after shutting off the fuel to a boiler which is to be secured, the __________.
- 792.A sudden increase in boiler water hardness or chloride content could indicate __________.
- 793.Thin sheets of mica are installed in boiler gage glasses to __________. I. reduce the effects of thermal exposure on the glass II. enhance the ability of the operator to observe the water level from a distance
- 794.The most critical period of main turbine operation is during cold start-up, rather than hot shutdown because __________.
- 795.Coast Guard Regulations (46 CFR), require main propulsion lube oil systems to be designed to function satisfactorily when the vessel has a permanent __________.
- 796.An accumulation test is performed on the boiler to determine the suitability of the safety valves and the set points __________. I. if the boiler normal operating pressure is permanently reduced II. when the steam generating capacity is increased
- 797.Coast Guard Regulations (46 CFR) require the temperature of the water leaving an oil fired, cast iron, low pressure, hot water heating boiler must not exceed __________.
- 798.Excessive carbon dioxide formed by improper chemical treatment in the boiler, may cause corrosion in the __________.
- 799.The main reason for having a low suction line on the fuel oil service or settling tanks is to __________.
- 800.What is the purpose of the movable air doors in an air register?