USCG Steam Plants – Question Bank Book 13 (BK13) — page 13
1769 questions with correct answers from the official USCG question bank (2008 edition), book 13 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1201.To comply with Coast Guard Regulations (46 CFR), which type of boiler listed shall be subjected to a hydrostatic test at one and one half times maximum allowable working pressure?
- 1202.A sequential lift, nozzle valve control bar on a turbo generator, utilizes which of the following operating principles?
- 1203.When the boiling temperature of a steam boiler is increased, which of the following effects will occur with relation to the pressure and the specific volume of the steam?
- 1204.Which system should be tested and used when required to raise the water level in an idle boiler?
- 1205.Which of the following represents a significant system limitation to be aware of when a burner management system is operated in the "Manual" mode?
- 1206.What is normally used to compensate for thermal expansion and contraction of the main turbine casing?
- 1207.Whenever operating a boiler, whose economizer is bypassed, always keep in mind that __________.
- 1208.The boiler fuel oil service pump normally takes suction from the __________.
- 1209.In a multi-burner firebox, a burner tip with a worn and enlarged orifice will __________.
- 1210.Which of the listed conditions can cause high superheater outlet steam temperature in an automated boiler?
- 1211.When sputtering is detected in the boiler fires indicating water in the fuel, which of the procedures listed should be followed?
- 1212.When testing boiler flue gas with a chemical absorption apparatus, to obtain accurate results __________.
- 1213.Contaminated steam generators in a contaminated drain system are usually __________.
- 1214.Which of the listed conditions can cause excessively high superheater outlet steam temperature in an automated boiler?
- 1215.When forced draft blowers are provided with high and low speed controls, it is advisable to run the blowers at high speed during maneuvering to __________.
- 1216.The boiler water level begins to fall very slowly due to the sudden failure of a water wall tube. In response to this situation, you should continue the feed water supply and immediately __________.
- 1217.Coast Guard Regulations (46 CFR) require unfired pressure vessels with manholes to be hydrostatically tested __________.
- 1218.Axial movement in a gear-type flexible coupling is provided for by __________.
- 1219.Where reaction turbine blading is fitted with shrouding of "end tightened" design, which of the following operating parameters must be carefully monitored for efficient turbine operation?
- 1220.Why is it occasionally necessary to verify the accuracy of the distilled water make-up feed tank remote level indicator?
- 1221.In the operation of a lube oil clarifier, the position of the oil-water interface should be __________.
- 1222.Which of the following reaction turbine components listed converts thermal energy into kinetic energy?
- 1223.The purpose of a contaminated steam system is to __________.
- 1224.Which component of a Kingsbury thrust bearing assembly transmits the thrust from the line shaft to the oil film and shoes?
- 1225.No lube oil appearing in the sight glass (bull's eye) of a gravity type system is a positive indication of __________.
- 1226.According to 46 CFR Part 61, which of the following statements is true concerning the inspection of water-tube boilers?
- 1227.A flame scanner installed in modern boiler combustion control systems, functions to __________.
- 1228.Which of the following is the advantage of operating a typical closed feed water system for a marine boiler when compared to an open feed water system?
- 1229.A primary function of burner atomization steam is to __________.
- 1230.The differential temperature of the main condenser cooling water will be significantly affected by a change in __________.
- 1231.A contaminated steam generator is used to produce saturated vapor from collected __________.
- 1232.Failure to use the turning gear prior to warming up a main turbine will damage the __________.
- 1233.What is the advantage of a forced water circulation boiler over a natural circulation boiler?
- 1234.In order to test the lifting pressure of the deaerating feed heater relief valve, you would __________. I. close the auxiliary exhaust dump valve to the main and auxiliary condensers II. increase the set point of the make-up steam regulator to the auxiliary exhaust system
- 1235.Coast Guard Regulations (46 CFR) require that main steam piping must be hydrostatically tested at specified intervals. If the pipe insulation cannot be removed during this test, the piping shall be tested at __________.
- 1236.The greatest resistance to heat transfer from the fireside to the waterside of a water-tube boiler generating tube takes place in the __________.
- 1237.All oil-fired main propulsion boilers with automatic safety control systems must automatically close the burner valve when __________.
- 1238.All oil-fired main boilers with automatic safety control systems must be provided with __________.
- 1239.Which of the following statements is true concerning the operation of the automatic shut down solenoid valve in the fuel oil service manifold of an automatically fired boiler?
- 1240.If oil is found in the main fuel oil heater steam drain system, which of the actions listed should be taken first?
- 1241.After being required to plug an excessive number of leaking condenser tubes on the main condenser, what changes would you expect to observe when returning to normal steam plant sea speed operation?
- 1242.Why is a flexible I-beam rigidly mounted at the forward end of the main turbine?
- 1243.If a feed pump failure causes the boiler water to drop out of sight in the gage glass, the engineer should FIRST __________.
- 1244.When starting a turbine driven boiler feed pump, care should be taken to insure that the re-circulating valve is open. Which of the following valves should be closed when starting?
- 1245.While on watch at sea, you notice the main lube oil pump suction vacuum has been increasing. To correct this you should __________.
- 1246.In any governor there is a small range of speed in which no corrective action occurs. This speed range is called the governor dead band and is caused by __________.
- 1247.A pilot valve and servomotor are utilized in mechanical-hydraulic governing systems on a turbo generator unit in order to __________.
- 1248.Dirt and/or metallic particles in a reduction gear lubricating oil system may cause which of the following problems to occur?
- 1249.During normal operation of a main propulsion turbine, the lube oil supply temperature to the bearings should be maintained at approximately __________.
- 1250.When starting a turbo generator, you must provide lube oil pressure to the governor power piston by means of __________.
- 1251.Lower than normal steam pressure in an operating boiler may be caused by __________.
- 1252.Most main propulsion reduction gear bearings are __________.
- 1253.To combat galvanic corrosion, condensers utilizing copper-nickel waterboxes are usually fitted with __________.
- 1254.Why is it necessary to have a relief valve protect the deaerating feed tank from internal pressure?
- 1255.A practical consideration to allow for when operating a boiler at low load with regard to heat absorption is the requirement to __________.
- 1256.The atmospheric drain tank (ADT) normally drains to the __________.
- 1257.Which of the DC heater operations listed will result in excessive dissolved oxygen in boiler water?
- 1258.During normal operation, the steam flow from the auxiliary exhaust line to the DC heater can be closely related to the __________.
- 1259.Scavenging air lines are connected to boiler stack periscopes to __________.
- 1260.Which action should be taken if the water level in the boiler gage glass drops out of sight and the burners fail to secure automatically?
- 1261.If the boiler fires are extinguished by water contamination in the fuel oil, you should FIRST __________.
- 1262.Coast Guard Regulations (46 CFR) require that boiler mountings shall be removed and studs examined by a Coast Guard inspector __________.
- 1263.Serious tube leaks in the air ejector condenser assembly may cause __________.
- 1264.Coast Guard Regulations, 46 CFR Part 54, require steam safety and relief valves to be provided with a substantial lifting device, capable of lifting the disc from its seat at what percentage of the set pressure?
- 1265.Proper vacuum must be maintained during prolonged astern operation to __________.
- 1266.The jacking/turning gear mechanism of a main propulsion geared turbine installation is normally connected through mechanical linkage to the __________.
- 1267.A common method of preheating main turbine lube oil prior to rolling over the main unit would be to ________.
- 1268.The level in the atmospheric drain tank when underway at sea, is normally maintained by the use of a/an __________.
- 1269.If the temperature of the fuel oil entering an atomizer is too low, the burner will __________.
- 1270.The rotating speed of the tubular bowl centrifuge is more than twice that of the disk type. The reason for this is __________.
- 1271.Excessive foaming in a steaming boiler can cause damage to the __________.
- 1272.What boiler water test would be given to insure that the boiler water contains sufficient chemicals to transform hard scale forming salts into harmless sludge which would eventually be removed with blowdowns?
- 1273.The reversing turbine is normally used for which of the following operations?
- 1274.The temperature of steam at the superheater outlet is influenced by the __________.
- 1275.If a steaming boiler begins 'panting,' the probable cause is __________.
- 1276.Which of the following statements is true concerning boiler inspections?
- 1277.If a salinity alarm system indicates 2.5 grains per gallon at the main condensate pump discharge, your first action should be to __________.
- 1278.What type of sensor is normally used with the automatic re-circulating valve in the main condensate line?
- 1279.When a lube oil purifier has been cleaned, but a small amount of sludge remains in one spot of the bowl side, the __________.
- 1280.The normal characteristics and properties of lube oil will begin to break down if contaminated with water and __________.
- 1281.On watch aboard ship, which of the following conditions will prevent a general service shipboard pump from achieving its maximum suction lift?
- 1282.An increase in clearance between reaction blade tips and the turbine casing will result in __________.
- 1283.In accordance with Coast Guard Regulations (46 CFR), which of the following statements is true concerning safety valve construction and/or operation used on propulsion boilers?
- 1284.Lube oil coolers are necessary in most engine lubricating systems because __________.
- 1285.An excess pressure governor is a special type of control device which would normally be found on a __________.
- 1286.The disk stack and tubular shaft used in a lube oil centrifugal purifier, is forced to rotate at bowl speed by __________.
- 1287.The most common cause of abnormal fireside burning of the boiler superheater tubes can "indirectly" be the result of __________.
- 1288.One function of a steam drum desuperheater installed in a high pressure boiler would be to __________.
- 1289.Which of the following statements describes the effects that dissolved oxygen has on boiler internal surfaces with changes in temperature and pressure?
- 1290.Reduction gears for main propulsion turbines are lubricated by __________.
- 1291.The boiler main feed pump aboard ship can operate with high temperature water without becoming vapor bound because the __________.
- 1292.Why is superheated steam used in the main propulsion turbine instead of saturated steam?
- 1293.The degree of fuel oil atomization is dependent upon the __________.
- 1294.Sodium sulfite is added to boiler water to chemically react with any __________.
- 1295.The most important consideration to take into account when water washing the firesides of a water tube boiler is __________.
- 1296.Thin sheets of mica are installed in boiler gage glasses to __________.
- 1297.The internal feed pipe in a D-type marine boiler provides __________.
- 1298.Which of the listed parts of a Kingsbury thrust bearing tilts to permit the formation of a wedge shaped film of oil?
- 1299.Which of the conditions will occur FIRST if the steam flow to the main engine, when at full power, is suddenly stopped?
- 1300.Coast Guard Regulations (46 CFR) state that main propulsion water-tube boilers are not required to be fitted with a surface blow off valve if the design pressure is __________.