USCG Steam Plants – Question Bank Book 13 (BK13) — page 2
1769 questions with correct answers from the official USCG question bank (2008 edition), book 13 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 101.In most marine boilers, the primary reason the first few rows of generating tubes, called screen or furnace row tubes, are made larger in diameter than the rest of the generating tubes is because __________.
- 102.A unit of measure used to express the chloride content of boiler water is __________.
- 103.Which of the following devices can be used to secure or hold furnace refractory in position?
- 104.When turbine rotor shafts extend through the casing, an external source of sealing steam is used in conjunction with labyrinth packing to __________.
- 105.A corbel in the furnace of a water-tube boiler is a fillet of plastic refractory used as a __________.
- 106.Ni-chrome wire is used when patching boiler furnaces for __________.
- 107.Which of the following statements is correct regarding the start-up operation of a non-condensing turbine-driven feed pump?
- 108.In a main propulsion steam turbine installation, the condensate pump initially discharges to the __________.
- 109.Slagging of boiler furnaces is a slow progressive action which is accelerated by __________.
- 110.Which constituent of fuel oil determines the specific heat?
- 111.Which of the listed refractory materials is capable of providing structural stability?
- 112.Which of the following statements represents the function of insulating brick?
- 113.A corbel in the furnace of a water-tube boiler is a __________.
- 114.Which of the following statements represents the function of insulation block?
- 115.When operating with the auxiliary feed line, feed water flow is controlled __________.
- 116.Serious tube leaks in the air ejector condenser assembly will cause __________.
- 117.The primary purpose of refractory mortar is __________.
- 118.Which of the following refractory materials contains a hydraulic-setting binder and develops strength without needing to be heated in a manner similar to concrete?
- 119.Pumps normally used for fuel oil service are __________.
- 120.A major difference between the two element and the three element feed water regulator control systems, is that a three element system will additionally measure and incorporate the __________.
- 121.Labyrinth seals used to reduce leakage around a turbine shaft are constructed of __________.
- 122.A corbel is used in a boiler furnace to __________.
- 123.Which of the following refractory materials is preferred for small repairs, particularly where standard size brick or tile cannot be used?
- 124.The cooling water flow from an air ejector inter condenser and after condenser is discharged directly into the __________.
- 125.As a general rule, for proper results castable fireclay must be air cured for __________.
- 126.Which of the significant combustible elements of fuel oil is a major source of boiler corrosion?
- 127.Which of the pumps listed is normally used in fuel oil service systems?
- 128.Phenolphthalein is used as an indicator to test boiler water for __________.
- 129.Where are moisture shields located in a main propulsion steam turbine?
- 130.Boiler refractory firebrick is secured to the casing by __________.
- 131.Which of the listed refractory materials will develop required strength only after being heated at a temperature of 1095°C (2000°F) or higher?
- 132.Makeup feed water is brought into an operating closed feed system via the __________.
- 133.Steam condensed in the air ejector inter condenser, drains to the __________.
- 134.Due to of the curing characteristics of plastic refractory, its use should be avoided in __________.
- 135.What is indicated by the code number 32Y20 stamped on a burner sprayer plate?
- 136.Phenolphthalein indicator is used in the boiler water test for __________.
- 137.Which of the listed refractory materials can be used as a substitute for insulating brick and insulating block in certain boiler walls construction?
- 138.Which of the following statements represents the function the nozzle assembly performs in an impulse turbine?
- 139.Boiler refractory anchor bolts are secured to the casing by __________.
- 140.Which of the listed refractory materials is a suitable substitute for insulating block only?
- 141.Which of the listed conditions will always result in dissolved oxygen being carried over from the main condenser?
- 142.The loop seal connected to the main condenser returns the drains from the __________.
- 143.A desirable property of boiler fuel oil is __________.
- 144.Which of the following statements represents the advantage of castable insulation over either insulating brick or insulating block installations?
- 145.A sodium sulfite test is performed on a boiler water sample to determine if __________.
- 146.Which of the listed refractory materials is composed of wool fibers and clay binders?
- 147.Nozzle diaphragms are installed in pressure-compounded impulse turbines to __________.
- 148.The primary purpose of insulating cement is __________.
- 149.Under EMERGENCY operating conditions, the proper valve positions for controlling feed water to the boiler should be the __________.
- 150.Which of the following refractory materials can provide a straight backing surface for insulation block where minor casing warp has occurred?
- 151.The presence of sulphur in fuel oil will most likely cause __________.
- 152.Which atomizing sprayer plate has the largest capacity?
- 153.Which of the listed refractory materials may be used with other machinery insulation arrangements outside of the boiler?
- 154.Brick bolts, tile bolts, and pennant anchors are attached to the inner casing by __________.
- 155.A pressure-velocity compounded impulse turbine consists of __________.
- 156.Which of the listed refractory materials can be used in an area directly exposed to the highest heat in the furnace?
- 157.Which of the following statements represents the primary function of handholes used on a boiler?
- 158.If manual control of the water level in a steaming boiler is required, the proper method of control is with the auxiliary feed __________.
- 159.In the condensate system, the automatic re-circulating valve can be actuated by the __________.
- 160.The primary source of steam to the auxiliary exhaust system is typically supplied directly from __________.
- 161.The most harmful slag forming compounds found in fuel oils are __________.
- 162.Which group of numbers would indicate the largest fuel capacity for a sprayer plate in a mechanical fuel oil atomizer?
- 163.Normally a boiler water sample should be taken __________.
- 164.The contaminated drain system normally receives drains that may be exposed to __________.
- 165.Which of the devices listed is found on an LP main propulsion steam turbine casing?
- 166.In a steam propulsion plant, the primary source of auxiliary exhaust steam is from the __________.
- 167.Which of the operating principles listed would apply to a single-element, thermo-hydraulic, feed water regulator?
- 168.Main condensate re-circulating systems are primarily intended to __________.
- 169.Which of the casualties listed is apt to occur immediately after a high water casualty?
- 170.Heavy slagging and high temperature corrosion of boiler tubes can result from using a fuel oil with high amounts of __________.
- 171.Which precaution should be observed to prevent damage to the fuel oil service pump when warming up the fuel service system?
- 172.The last two digits stamped on a fuel oil atomizer sprayer plate represents the cross-sectional area ratios of the tangential slots and orifice. This ratio determines the __________.
- 173.In a water-tube boiler, circulation is caused by the difference in the __________.
- 174.Shrouding on impulse turbine blading is held in place by __________.
- 175.The means of circulation commonly found in water-tube boilers is __________.
- 176.Which of the following statements is true concerning the operation of a boiler thermo-hydraulic feed water regulator?
- 177.The DC Heater functions to __________.
- 178.A lower than normal boiler stack gas temperature usually indicates __________.
- 179.The number '29' on a fuel oil burner sprayer plate marked '2909' indicates the __________.
- 180.Eight (8) ounces of oxygen, dissolved in 500,000 pounds of water, is a concentration of __________.
- 181.The steam separator as used in conjunction with a steam whistle normally drains to which of the listed drain systems?
- 182.Allowance for axial expansion of the steam turbine due to temperature changes is provided for by the use of __________.
- 183.Which of the following statements concerning boiler steam drum surface blow piping is correct?
- 184.Clean low pressure steam drains are collected in the __________.
- 185.In a single-element feed water regulator, the amount of valve opening and closing is controlled by the __________.
- 186.Which statement is true concerning drain inspection tanks?
- 187.From which of the areas listed are condensate drains normally collected and returned to the low pressure drain system?
- 188.Economy and efficiency in the operation of a marine boiler have traditionally been characterized by __________.
- 189.When warming up a fuel oil service system, you should open the steam supply to the fuel oil heaters __________.
- 190.A dissolved oxygen concentration of 8.0 ppm represents __________.
- 191.The level in the atmospheric drain tank is normally maintained by the use of a/an __________.
- 192.In a boiler equipped with a convection type superheater, the superheater tubes are located __________.
- 193.Single-element automatic feed water regulators are controlled by the __________.
- 194.The DC heater functions to __________.
- 195.If live steam is supplied directly to the tank heating coils, the collected drains in the 'clean' section of the contaminated drain inspection tank are removed directly to the __________.
- 196.A light brown haze issuing from the boiler smoke stack generally indicates __________.
- 197.The entire unit which houses the burner, air scoop, air doors and bladed cone is correctly called the __________.
- 198.If it should become necessary to abandon a compartment because of the danger of a large steam leak on a boiler, which of the following actions represents the best avenue of escape?
- 199.The percentage by weight of steam in a mixture of steam and water is called the __________.
- 200.The correct radial clearances between the rotor and the casing in a propulsion turbine are maintained by the turbine __________.