USCG Electricity – Question Bank Book 12 (BK12) — page 10
1209 questions with correct answers from the official USCG question bank (2008 edition), book 12 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 901.Electric motors intended for use outside the engine room and boiler room are frequently rated to run at a designed ambient temperature of 40°C. What is the equivalent temperature in degrees Fahrenheit?
- 902.To properly seat the brushes on a commutator or slip rings, you should use __________.
- 903.Which of the following statements, concerning the general maintenance of a brushless generator, is correct?
- 904.Which of the following methods should be used to dress the face of silver-plated motor controller contacts?
- 905.When power is restored after a complete power failure, the steering gear pump motor which was on-line, will normally __________.
- 906.A four-pole 60-hertz induction motor has a synchronous speed of 1800 RPM and a slip of 4 percent at full load. What will be its full load speed?
- 907.A useful instrument for checking 3 phase A.C. motor performance by measuring possible unbalanced currents is the __________.
- 908.The speed of a squirrel-cage, multi-speed, induction motor, as used aboard ship, is varied by changing the __________.
- 909.The KW load is evenly distributed between two alternators just placed in parallel by adjusting __________.
- 910.Ambient temperature is the __________.
- 911.An electric motor can be designed and constructed to be __________.
- 912.The nominal open-circuit voltage of one cell of a fully charged lead-acid battery is __________.
- 913.The nominal open-circuit voltage of one cell of a fully charged wet cell nickel cadmium battery is __________.
- 914.When the length and cross sectional area of a wire are both tripled, the resistance __________.
- 915.A delayed-action fuse is most frequently used in which of the listed circuits?
- 916.When energizing a DC propulsion motor using "local override manual control", the variable rheostat should be turned __________.
- 917.Universal motors will operate on AC or DC current, and are generally found in __________.
- 918.The power factor of an electrical distribution system being supplied by a single AC generator is determined by the __________.
- 919.Hysteresis loss in transformers can be reduced by __________.
- 920.Motorization of an AC generator is undesirable because __________.
- 921.If overloading an electric motor becomes necessary in an emergency, you should __________.
- 922.In a three-phase, squirrel-cage type, induction motor, the primary rotating magnetic field is established by the __________.
- 923.If many turns of an alternating current coil for a contactor become short circuited, the coil __________.
- 924.DC generator voltage is decreased by __________.
- 925.A motor enclosure which protects against falling liquids is classified as __________.
- 926.The electric brake on an deck cargo winch functions to __________.
- 927.Which of the following statements concerning the maintenance of solid-silver contacts in relays and auxiliary control circuits is correct?
- 928.In addition to testing the calibration of a circuit breaker, maintenance should include all of the following EXCEPT __________.
- 929.Which of the following would best describe a standard electric meter movement that uses a stationary permanent magnet and movable coil?
- 930.Unnecessary and frequent applications of insulating varnish to the generator stator windings to repair defective insulation will result in __________.
- 931.As a result of a serious mechanical malfunction in one of the ship's service generators operating in parallel, you must secure that generator. In order to prevent a possible overload to the remaining generator, which of the following sequential courses of action should be taken?
- 932.What is the main function in the use of a capacitor for starting a single phase motor?
- 933.Which of the listed safety features should be provided in small rooms or lockers where batteries are stored?
- 934.The most probable reason the contacts of a motor starter or controller fail to drop out when the 'stop' button is depressed, is that the __________.
- 935.Which of the following electric motors would be the most reliable to use on the open main deck of a vessel?
- 936.Which of the following precautions should be taken when troubleshooting various power circuits using a common mechanical solenoid-type voltage tester (Wiggins)?
- 937.In a basic induction motor, rotor currents are circulated in the rotor by __________.
- 938.The speed of a synchronous ac propulsion motor is__________.
- 939.A circuit breaker for a 300 KW alternator is rated at 470 amperes of full continuous load. The amount of over current allowed is 125%. Which of the following conditions will trip the breaker?
- 940.A low-voltage protection circuit as used in electric motor starting equipment, will __________.
- 941.Which of the following represents the recommended maximum allowable temperature for electrolyte in a lead-acid battery?
- 942.The most practical method of controlling the RPM of a step-speed AC motor is to __________.
- 943.A loud buzzing noise in an AC controller is probably caused by __________.
- 944.Accidental grounds in a shipboard electrical system must be repaired as soon as possible as they will __________.
- 945.An open primary coil in a simple transformer will be indicated by which of the listed conditions?
- 946.On a main switchboard, if all three ground detection lamps burn with equal intensity when the test button is depressed, which of the listed conditions is indicated?
- 947.Protection against sustained overloads occurring in molded-case circuit breakers is provided by a/an __________.
- 948.The pitting of controller contacts can be caused by __________.
- 949.A diesel driven emergency generator is prevented from being paralleled with the ship's service generators by __________.
- 950.The energy consumed by an AC motor, as strictly reactive power, is __________.
- 951.As load is added to a DC shunt motor, the motor will __________.
- 952.Under voltage trips are frequently installed on switchboard circuit breakers to __________.
- 953.The purpose of having low voltage protection for an electric motor circuit is to __________.
- 954.Which of the following statements identifies the difference between the primary windings and the secondary windings of a 2:1 step-down transformer?
- 955.Which of the listed features would require a motor controller to be manually re-started following a power failure?
- 956.A turbo generator has a rated output of 1200 KW at 60 Hertz, with a no load frequency of 61.5 Hertz. What is its speed droop?
- 957.Proper maintenance of a D.C. motor's commutator includes __________.
- 958.If an alternator is to be inactive for a considerable period of time, which of the following actions should be taken?
- 959.Which of the following is a characteristic of fractional horsepower repulsion start motors?
- 960.When a nickel-cadmium battery begins gassing while connected to the battery charging circuit, you should __________.
- 961.When troubleshooting a lead-acid storage battery, a weak or dead cell is best detected by __________.
- 962.Engine room watch standers should keep a constant check on the loads carried by electric motors because __________.
- 963.What is the approximate discharge voltage produced by one wet cell of a nickel-cadmium battery?
- 964.If a single-phase induction motor fails to start, the problem may be __________.
- 965.To determine if a stator coil on a AC generator is grounded, you should use a/an __________.
- 966.A vessel is equipped with two ship's service generators. Generator #1 is rated at 900 kw and generator #2 is rated at 600 kw. During parallel operation, with a hotel load of 1,000 kw, what should be the kw load on generator #2?
- 967.One method of testing for a reversed shunt field coil in a DC motor is by connecting the coil to a low voltage source, and test for polarity using a/an __________.
- 968.Which of the listed motors will operate at the highest RPM, assuming that each operates at the same frequency?
- 969.Which of the following statements represents the important factor that must be considered when replacing a faulty diode in a generators excitation field rectifier assembly?
- 970.When charging a wet cell nickel-cadmium battery, __________.
- 971.A bus disconnect link is used to isolate __________.
- 972.Two DC drive propulsion motors provide input to a single output reduction gear. Upon relieving the watch, you notice that the starboard motor indicators show reduced voltage and zero current compared to normal voltage and current indicated on the port motor. The problem with the starboard motor could be __________.
- 973.Voltage failure of an AC generator may be caused by __________.
- 974.Electrical power loss due to hysteresis is a result of _________.
- 975.A three-phase alternator is operating at 450 volts, 250 amps at 0.6 power factor. If the power factor increases to 0.8, the kw load potential will increase by __________.
- 976.The best tool to use to remove a ball bearing from the shaft of a motor would be a __________.
- 977.On large generators, space heaters are used to __________.
- 978.If a small electric motor has been immersed in salt water, it should be __________. I. thoroughly rinsed in fresh water and completely dried II. initially started with reduced voltage
- 979.If a DC motor runs faster than designed, with all other conditions being normal, the possible cause could be a/an __________.
- 980.Wet armature windings in a D.C. motor may lead to __________.
- 981.A low voltage source is applied to the collector rings of a salient-pole alternator to test for shorted coils. As the voltage drop across each coil is recorded, a coil with a short circuit will be indicated by a __________.
- 982.The purpose of the commutator and brushes on a DC generator is to __________.
- 983.Which of the following statements concerning a wet cell Nickel-Cadmium battery is true?
- 984.Hand-portable phase sequence indicators should be used when __________.
- 985.The specific gravity of the electrolyte solution in a lead acid battery __________.
- 986.Which of the following materials is recommended for finishing the slip rings of an electric motor after grinding or turning?
- 987.AC and DC generators are similar in that they __________.
- 988.A useful instrument for checking the performance of an operating poly phase AC motor would be a __________.
- 989.The operating torque of the disk or timer element in an AC reverse power relay is obtained from __________.
- 990.AC generator circuits are protected against malfunctions due to prime mover power loss by the use of __________.
- 991.DC generator circuits are protected against malfunctions due to prime mover power loss by the use of __________.
- 992.A change in field excitation of an alternator operating in parallel will cause a change in its __________.
- 993.A milliammeter, with a full scale deflection reading of 100 milliamps, is known to have an accuracy of plus or minus 2%. A meter reading of 5 milliamps would indicate a line current of between __________.
- 994.A megger is being used to test the insulation of an AC generator. The resistance value of a dry, clean winding will __________.
- 995.Which statement is true concerning a split-phase induction motor?
- 996.Which of the following statements is true concerning a large polyphase synchronous main propulsion motor?
- 997.Which of the following represents the accepted method of cleaning dust and foreign particles from electrical equipment while limiting damage to electric components?
- 998.A load with an impedance of 440 ohms is connected across the secondary of a step-up transformer. If the input voltage is 110 VAC and the step-up ratio is 10, what will be the primary current?
- 999.Germanium semiconductor diodes are commonly used as __________.
- 1000.The amount of voltage induced in the stator windings of a modern AC generator depends mainly on __________.