USCG Electricity – Question Bank Book 12 (BK12)
1209 questions with correct answers from the official USCG question bank (2008 edition), book 12 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1.When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an __________.
- 2.On a vessel with turbo-electric drive, which of the following conditions would indicate that the propulsion motor had dropped out of synchronization with the propulsion generator?
- 3.On some diesel-electric ships, the DC propulsion motor will only attain half speed when the generator fields are fully excited. Speeds above this are obtained by __________.
- 4.In a diesel electric plant, raising the generator's field excitation will cause the DC propulsion motor to __________.
- 5.Electric coupling excitation is reduced at slow speeds to __________.
- 6.A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by __________.
- 7.A semiconductor that decreases in resistance with an increase in temperature is known as a __________.
- 8.The shunt used in an ammeter should be connected in __________.
- 9.Brushless generators are designed to operate without the use of __________.
- 10.An operating characteristic appearing on the name plates of shipboard AC motors is __________.
- 11.Low horsepower, polyphase, induction motors can be started with full voltage by means of __________.
- 12.Which of the listed devices may be installed on a large turbo-electric alternating current propulsion generator?
- 13.Moisture damage, as a result of condensation occurring inside of the cargo winch master switches, can be reduced by __________.
- 14.Which of the following conditions will occur if the solenoid coil burns out on a cargo winch with an electrical brake?
- 15.Which of the listed battery charging circuits is used to maintain a wet-cell, lead-acid, storage battery in a fully charged state during long periods of disuse?
- 16.In the event of a power failure during cargo loading operations, the movement of an electric powered cargo winch will be stopped by __________.
- 17.A ground can be defined as an electrical connection between the wiring of a motor and its __________.
- 18.External shunts are sometimes used with ammeters to __________.
- 19.The output voltage of a 440 volt, 60 hertz, AC generator is controlled by the __________.
- 20.Which of the following statements represents the main difference between a relay and a contactor?
- 21.Which of the following statements represents an application of a silicon controlled rectifier?
- 22.The electrolyte used in a nickel-cadmium battery is distilled water and __________.
- 23.What damage may occur to the components of a winch master control switch, if the cover gasket becomes deteriorated?
- 24.An accidental path of low resistance, allowing passage of abnormal amount of current is known as a/an __________.
- 25.A resistance in a circuit of unknown value is to be tested using the voltmeter/ammeter method. Therefore, the meters should be connected with __________.
- 26.In general, polyphase induction motors can be started on full line voltage by means of __________.
- 27.The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide __________.
- 28.A direct current passing through a wire coiled around a soft iron core is the description of a simple __________.
- 29.To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST __________.
- 30.The use of four diodes, in a full-wave bridge rectifier circuit, will __________.
- 31.Autotransformer starters or compensators are sometimes used with polyphase induction motors to __________.
- 32.A molded-case breaker provides protection against short circuits by using a/an __________.
- 33.The method used to produce electron emission in most vacuum tubes is known as __________.
- 34.When troubleshooting electronic equipment, you should use a high impedance multimeter __________.
- 35.Which of the listed devices is used to measure pressure and convert it to an electrical signal?
- 36.Grounds occurring in electrical machinery as a result of insulation failure may result from __________.
- 37.The amount of voltage induced in the windings of an AC generator depends on __________.
- 38.An AC motor using a rheostat in the motor circuit to vary the speed is called a __________.
- 39.Which of the following precautions should you take when securing propulsion generators and motors for an extended period of time?
- 40.The device that most commonly utilizes the principle of electromagnetic induction is the __________.
- 41.A tubular fuse should always be removed from a fuse panel with __________.
- 42.One factor that determines the frequency of an alternator is the __________.
- 43.The variable resistance placed in the rotor circuit of a wound-rotor induction motor provides for __________.
- 44.Which of the motors for the devices listed below is fitted with an instantaneous overload relay?
- 45.A molded-case circuit breaker provides protection against short circuits by using a/an __________.
- 46.Which of the following statements concerning analog and digital devices are correct?
- 47.The number of cells in a 12 volt lead-acid battery is __________.
- 48.The Wheatstone bridge is a precision measuring instrument utilizing the principle of changes in __________.
- 49.The greatest detrimental effect on idle electrical equipment, such as cargo pump motors, is the __________.
- 50.The frequency output of an operating alternator is controlled by the __________.
- 51.Which of the following physical characteristics does a wound-rotor induction motor possess that a squirrel cage motor does not?
- 52.The current at which a magnetic-type overload relay tends to trip may be decreased by raising the plunger further into the magnetic circuit of the relay. This action __________.
- 53.When choosing a battery for a particular application, major consideration should be given to the battery's __________.
- 54.The rated temperature rise of an electric motor is the __________.
- 55.Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in armature reaction are compensated for by the __________
- 56.An electrical device which prevents an action from occurring until all other required conditions are met is called a/an __________.
- 57.A circuit breaker and a fuse have a basic similarity in that they both __________.
- 58.The electrolyte in a lead-acid storage battery consists of distilled water and __________.
- 59.The torque produced by a motor when its shaft will not turn, even though rated voltage is applied to the stator, is known as __________.
- 60.Electrical leads and insulation on a motor should be painted with __________.
- 61.A degree of control over the speed of a slip ring induction motor can be obtained by __________.
- 62.A circuit breaker differs from a fuse in that a circuit breaker __________.
- 63.Incandescent lamps are classified according to __________.
- 64.As a general rule, the first troubleshooting action to be taken in checking faulty electric control devices is to __________.
- 65.An electrical device which employs a stationary armature and a rotating electromagnetic field is commonly used aboard ship as a __________.
- 66.The main purpose of the auxiliary winding on a split-phase, single-phase motor is to __________.
- 67.Which of the following statements describes the significance of ambient temperature in relation to the service life of electronic components?
- 68.The state of charge of a lead acid storage battery is best indicated by the __________.
- 69.The first requirement for logical troubleshooting of any system is the ability to __________.
- 70.The load sharing characteristics of two diesel generators operating in parallel are mostly dependent on their governor __________.
- 71.What type of rotor is used in split-phase motors?
- 72.Tightly knit metal braid wire can be used with a printed circuit board when __________.
- 73.AC circuits possess characteristics of resistance, inductance, and capacitance. The capacitive reactance of a circuit is expressed in __________.
- 74.In an AC generator, direct current from a separate source is passed through the windings of the rotor __________.
- 75.The purpose of a cage rotor winding placed on the rotor of a synchronous motor is to __________.
- 76.Motor controllers are seldom troubled with grounds because __________.
- 77.The electrical energy necessary to transmit a person's voice over a sound-powered telephone circuit is obtained from __________.
- 78.Which of the listed procedures should be carried out to prevent moisture damage to electrical apparatus during extended periods of idleness?
- 79.A constant output voltage from an AC generator is maintained by the __________.
- 80.Amortisseur windings are installed in a synchronous motor to __________.
- 81.Electric strip heaters are used in motor controllers to __________.
- 82.A fuse that blows often should be replaced only with a fuse of __________.
- 83.Which of the listed conditions is an advantage of a PN diode over a vacuum diode?
- 84.The freezing point of the electrolyte in a fully charged lead-acid battery will be __________.
- 85.The heating of conductors as a result of resistance in a distribution circuit causes a power loss expressed as __________.
- 86.To repair a small electrical motor that has been submerged in saltwater, you should __________.
- 87.The output voltage of a three-phase alternator is regulated by the __________.
- 88.The function of damper windings in a synchronous motor is to __________.
- 89.A shading coil used in an AC magnetic controller, functions to __________.
- 90.In a cartridge-type fuse, the metal element is contained in a __________.
- 91.In process control terminology, continuously variable values which change without distinct increments, such as temperature, pressure, or level are called __________.
- 92.The proper way to apply plastic electrical tape to an electric cable splice is to __________.
- 93.Which of the following statements is true concerning all three-phase alternators?
- 94.Time delayed or delayed action-type fuses are designed to __________.
- 95.Silicon diodes which are designed for a specific reverse breakdown voltage, and are most often used in electronic power supply voltage regulators, are called __________.
- 96.Which of the following statements best describes the material known as varnished cambric?
- 97.A synchronous motor maintains synchronism with the rotating field because __________.
- 98.What is the maximum allowable primary current of a 2 KVA step-down transformer with a four to one turns ratio if the primary is connected across a 440 volt line?
- 99.The part of a fuse that melts and opens an electrical circuit is typically made of __________.
- 100.The cross-sectional area of shipboard electrical cable is expressed in __________.