USCG Electricity – Question Bank Book 12 (BK12) — page 11
1209 questions with correct answers from the official USCG question bank (2008 edition), book 12 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 1001.Routine A.C. motor maintenance should include periodic __________.
- 1002.Materials that retain a large part of their magnetization, after the magnetizing force is removed, are said to have __________.
- 1003.Which of the listed colors properly describes a DC motor commutator when correct commutation is taking place?
- 1004.When checking the specific gravity of battery electrolyte with a hydrometer, which of the following statements is true?
- 1005.The air gap provided in an induction motor should be checked periodically with a feeler gage to detect __________.
- 1006.A common method used to control the speed of a synchronous AC propulsion motor on a diesel-electric propulsion drive is by __________.
- 1007.To best determine the state of charge of a wet cell nickel-cadmium battery, you should __________.
- 1008.An AC generator produces 60 Hz at 1800 RPM. If the generator speed is increased to 1830 RPM, the cycles will __________.
- 1009.If a DC motor runs hot, the cause may be __________.
- 1010.Brushes in a generator must be positioned in the neutral plane to avoid sparking between the brushes and the __________.
- 1011.If the connections for the field and the armature on a DC motor are reversed, __________.
- 1012.The most practical method used for resurfacing a ship's main propulsion motor commutator is to __________.
- 1013.According to 46 CFR Subchapter J, electric motors operating in a boiler room machinery space must be designed for an ambient temperature of __________.
- 1014.When a nickel-cadmium battery begins gassing while connected to the battery charging circuit, you should __________.
- 1015.A lead-acid battery can deliver 20 amperes continuously for 10 hours with an ampere-hour rating of __________.
- 1016.In a diesel electric plant, raising the AC generator's field excitation will cause the DC propulsion motor to __________.
- 1017.An advantage of DC motors over AC motors is that they __________.
- 1018.A DC ammeter would normally be connected __________.
- 1019.A megohmmeter is used to measure __________.
- 1020.Which statement is NOT true concerning electric propulsion drives?
- 1021.A twelve volt lead-acid battery is constructed of __________.
- 1022.A cycloconverter (CCV) is a static power converter that __________.
- 1023.Moisture accumulating in electric motors and generator windings having a cold insulation resistance greater than 50,000 ohms may be baked out with internal heat. This heat can be developed by __________.
- 1024.A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________.
- 1025.An electric propulsion drive system in which the propulsion generator supplies power to both the propulsion motor and ship service loads is referred to as a __________.
- 1026.Equipment for dc propulsion drive systems usually includes __________.
- 1027.The type of motor generally used in dc propulsion drive systems is the __________.
- 1028.Reversal of a dc propulsion motor is achieved through __________.
- 1029.An electric heating element supplied with 120 volts draws 15 amps. How much power will be consumed?
- 1030.Uneven wear of the commutator surface on a direct current propulsion motor can be caused by __________.
- 1031.Which of the listed conditions is an advantage of a PN diode over a vacuum diode?
- 1032.One function of the movable contacts in a drum-type motor controller is to __________.
- 1033.The plates of a wet cell NiCad storage battery are made from __________.
- 1034.The propeller shaft speed in a diesel-electric, AC-synchronous, propulsion drive motor is changed by varying the __________.
- 1035.While standing watch onboard a diesel-electric propulsion drive ship, you notice the main transformer core temperature slowly rising. You should first __________.
- 1036.The torque produced by a DC motor armature is the product of the force acting at the armature surface multiplied by __________.
- 1037.The propulsion motor most often utilized in an ac drive system operating in the moderate to high power range is the __________.
- 1038.If the approximate voltage to be measured in an electric circuit is not known, you should __________.
- 1039.Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply?
- 1040.When you are making a high potential test (megger) on the motor coils of repaired electrical machinery, a rise in leakage current indicates __________.
- 1041.To perform an insulation resistance test of an individual electric motor coil, the megohmmeter should be connected to __________.
- 1042.Which of the following statements concerning the specific gravity of a battery electrolyte is true?
- 1043.An AC generator is prevented from becoming motorized by the use of a/an __________.
- 1044.To determine the state of charge of a wet cell nickel-cadmium battery, you should __________.
- 1045.An ohmmeter reading of 'zero' ohms between the ends of a wire conductor would provide a positive indication of __________.
- 1046.When replacing a fuse with one of a higher rating than the original, which of the following is true?
- 1047.During maintenance of circuit breakers, __________.
- 1048.Two 100 watt light bulbs are connected in parallel across a 100 volt power supply. The total power developed in the circuit is __________.
- 1049.According to 46 CFR Part 58, if a steering motor becomes overloaded, the __________.
- 1050.In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the __________.
- 1051.On an engine throttle control system, the auxiliary control circuits are provided with devices to prevent excessive over travel of the actuating valve by the control motor. These devices are commonly called __________.
- 1052."Low Voltage Release" (LVR) protection used in some shipboard motor starters and other control equipment will have which of the following characteristics?
- 1053.Increasing the load on the secondary windings of a transformer will cause a/an __________.
- 1054.The timer element of a reverse power relay will activate when __________.
- 1055.If the voltage supplied to the lighting circuit is 110 volts, how much current is used by a 100 watt light bulb?
- 1056.An AC generator power panel is fitted with two synchronizing lamps and a synchroscope. When paralleling, if the synchroscope pointer is at the noon position and one synchronizing light is bright while the other remains dark, this indicates that __________.
- 1057.Which of the listed faults can only be eliminated by turning or grinding the face of a commutator with a rigidly supported tool?
- 1058.While underway onboard a DC diesel-electric drive ship, you notice excessive sparking of the brushes on the main propulsion motor. You should first __________.
- 1059.Which of the listed conditions could cause a recently overhauled DC motor to have excessively hot windings and sparking at the brushes?
- 1060.Two DC drive propulsion motors provide input to a single output reduction gear. Upon relieving the watch, you notice that the starboard motor indicators show zero current compared to normal voltage and current indicated on the port motor. The problem with the starboard motor could be __________.
- 1061.A three-phase electrical system is equipped with ground detecting lamps. If one of the lamps is dark, and remains dark when the test switch is operated, this indicates __________.
- 1062.Three 12 volt, lead-acid, batteries connected in series will develop __________.
- 1063.The existing resistance of a conductor is dependent upon its length, cross-sectional area, __________.
- 1064.Which of the following statements concerning AC circuits is correct?
- 1065.How will a molded-case circuit breaker react after it has tripped, as a result of an overloaded circuit?
- 1066.Prior to performing any internal maintenance on a large DC main propulsion motor, precautions should be taken to __________.
- 1067.Heat sinks are most frequently used with __________.
- 1068.What is the wattage of a heating element drawing a current of 30 amperes, at 120 volts?
- 1069.On a digital numerical display readout, what would be the minimum number of LED segments required to form and display any digit 0 through 9?
- 1070.The windings of electric generators during short idle periods should be __________.
- 1071.A basic electrical meter sensing device that responds to the flow of current through an electromagnetic coil commonly used in DC ammeters, voltmeters, and ohm meters is called a __________.
- 1072.The leads from a ohmmeter are attached to the leads of an AC motor field coil. A reading of infinity is obtained indicating a/an __________.
- 1073.A flickering ground detection lamp on a AC electrical power panel could be caused by a __________.
- 1074.A general purpose electrical multimeter can be used to directly measure __________.
- 1075.A four pole, 60 Hz, three-phase synchronous motor comes up to 1760 RPM when started as an induction motor. What is the percent slip after the rotor field is energized?
- 1076.In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to __________.
- 1077.For routine cleaning of a commutator, you should apply __________.
- 1078.Two contributors of electronic console failures are heat and vibration. To combat some of their effects, preventive maintenance procedures should include __________.
- 1079.Reduced voltage applied to an AC induction motor during the starting period will __________.
- 1080.A hydrometer indicates specific gravity by comparing the __________.
- 1081.When soldering a printed circuit board component, you should be careful to prevent damage by __________.
- 1082.The charge of a lead-acid battery is normally checked with a/an __________.
- 1083.The force that causes free electrons to flow in a conductor producing electric current is called a/an __________.
- 1084.Brush sparking in a DC generator during commutation may be caused by __________.
- 1085.The conversion of constant frequency power into adjustable frequency power in a modern AC propulsion drive system is commonly achieved through the use of __________.
- 1086.An alternator will fail to produce line voltage as a result of __________.
- 1087.When correcting specific gravity readings of a lead-acid battery for existing temperature conditions, you should __________.
- 1088.A single-phase induction motor having a relatively high starting torque, is the __________.
- 1089.What will be the output frequency of a three-phase, six pole, AC generator operating at 1800 revolutions per minute?
- 1090.When a lead-acid battery starts to gas freely after receiving a normal charge current, the charging current should be __________.
- 1091.In a compound-wound motor, a portion of the line current flows through the __________.
- 1092.The air gap in an induction motor should be periodically checked with a feeler gage to indicate __________.
- 1093.Cartridge type fuses contain meltable elements that are generally made from __________.
- 1094.One diode of a single phase, center tap, full-wave rectifier has burned out in a shorted condition. Therefore, the output will be __________.
- 1095.Which of the following is true when comparing a primary type and secondary type storage battery?
- 1096.The best method used to properly resurface an eccentric commutator on a small DC electric motor is to __________.
- 1097.A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp?
- 1098.If a circuit has resistances of 5, 10, and 20 ohms connected in parallel, what is the combined resistance of the circuit?
- 1099.What power is consumed by a heating element using a current of 20 amperes at 120 volts?
- 1100.If a shipboard AC generator experiences voltage failure, the cause may be due to __________.