USCG Electricity – Question Bank Book 12 (BK12) — page 4
1209 questions with correct answers from the official USCG question bank (2008 edition), book 12 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 301.The division of kilowatt load between two paralleled alternators is determined by the __________.
- 302.The set point current at which a magnetic-type overload relay tends to trip may be increased by turning the dashpot in the 'lower' direction. This action __________.
- 303.The timer element of a reverse power relay cannot be energized unless __________.
- 304.Before touching a small capacitor connected to a de-energized circuit, or even one that is completely disconnected, you should __________.
- 305.A breakable, mercury-filled thermometer should not be used in a lead-acid battery to measure electrolyte temperature, as an accidental breakage can cause __________.
- 306.Which of the following statements is true concerning simple parallel resistance circuits?
- 307.Which of the listed statements is correct when using an analog multimeter as an ohmmeter?
- 308.Kilowatt load is divided between two AC generators operating in parallel by __________.
- 309.An increase in which of the listed conditions will increase the speed of a synchronous electric motor?
- 310.Before working on an electric cargo winch master switch or controller, you should __________.
- 311.The pushbutton on the handset of a ship's sound-powered telephone must be depressed to __________.
- 312.When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should __________.
- 313.The frequency of an alternator at a given RPM is determined by the __________.
- 314.Which of the following methods should be used to test for an 'open' coil in an AC motor stator?
- 315.If a three-phase induction motor malfunctions and drops to a single-phase (one supply line open) __________.
- 316.During its operation, loud buzzing and resultant welding of contacts of a magnetic relay may be caused by __________.
- 317.Although saturable reactors are extremely useful in some applications, their gain is low because of __________.
- 318.In a three-phase circuit, the phase voltages are __________.
- 319.A solid-state circuit is inoperative; the FIRST action that should be taken is to __________.
- 320.Which of the problems listed will occur if a lead-acid battery is allowed to remain in a discharged condition for a long period of time?
- 321.The division of the kilowatt load between two AC generators operating in parallel is controlled by the settings and characteristics of the __________.
- 322.Most three-phase induction motors of five horsepower or less, are started by __________.
- 323.If a magnetic controller relay fails to drop out when the coil voltage is removed from the relay, the probable cause may be __________.
- 324.When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to __________.
- 325.When charging a 100 amp-hour lead-acid battery, __________.
- 326.When testing a capacitor with an analog type ohmmeter, a good capacitor will be indicated when __________.
- 327.The division of kilowatt load between two paralleled alternators is determined by the __________.
- 328.The synchronous speed of an induction motor is the __________.
- 329.The charging of lead-acid storage batteries will always result in __________.
- 330.When the current flow through a power transmission line is doubled, the power loss __________.
- 331.While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to check its value?
- 332.Which of the following procedures should be used to determine the load of a three-phase, delta wound, AC generator?
- 333.An across-the-line starter provides __________.
- 334.Excessive heat in an operating motor controller can result from __________.
- 335.Transformers are used onboard ships with AC generators to __________.
- 336.A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device?
- 337.The full load torque of an electric motor is the __________.
- 338.Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be returned to 'zero' on the scale?
- 339.The speed of a wound-rotor induction motor __________.
- 340.If you hear a loud buzzing noise coming from a magnetic motor controller, you should __________.
- 341.The function of the autotransformers used with the starters of large AC motors is to provide __________.
- 342.When lead-acid batteries are charging, they always give off hydrogen gas that is __________.
- 343.The resistance of most conducting materials will change as a result of temperature change. The resistance of copper will __________.
- 344.How will the value of the output frequency change if the load is removed from a turbo generator having a governor speed droop setting of 3%?
- 345.Reversing any two of the three rotor leads on a wound-rotor induction motor will __________.
- 346.The function of a step-down potential transformer is to reduce the load __________.
- 347.To avoid damaging the components of a printed circuit board when testing it with a DC volt-ohmmeter, you should __________.
- 348.A resistor placed in parallel to the output of a power supply __________.
- 349.As load is added to an AC generator provided with constant field excitation, the prime mover slows down with the effect of __________.
- 350.A characteristic of an induction motor with a low resistance rotor winding is __________.
- 351.In troubleshooting a circuit in a console, you find that a resistor may be faulty. Which of the precautions listed must be observed when using an ohmmeter to carry out this test?
- 352.The state of charge of a lead-acid battery is best indicated by the __________.
- 353.The most inefficient method of voltage reduction from the stand point of power loss, is a/an __________.
- 354.Which is a function of the voltage regulators used with AC generators?
- 355.If an induction motor were to be operated at 90% rated voltage, __________.
- 356.When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is __________.
- 357.If both the 'high level' and 'low level' alarms come on for the same address of a centralized control console, the most likely problem is a/an __________.
- 358.A transformer works on the basic principle of __________.
- 359.Before measuring an unknown resistance with an ohmmeter, you should __________.
- 360.The instantaneous reduction in voltage of an AC generator, resulting from an increase in load, and prior to the automatic voltage regulator correcting the situation, is called voltage __________.
- 361.A characteristic of a wound-rotor induction motor, with a high resistance rotor winding, is __________.
- 362.You have installed a Zener diode in parallel with a load. While measuring the voltage across the Zener diode it is found that it does not change as the current through the load increases. This means that the Zener diode __________.
- 363.Violent gassing from a lead-acid battery while it is being charged, indicates that the __________.
- 364.An ohmmeter can be used to measure __________.
- 365.Under normal conditions, the speed of a two-speed squirrel cage induction motor is changed by varying the __________.
- 366.Magnetic controller contacts may become welded together during operation because of __________.
- 367.If a transformer is connected to a DC source, the transformer will overload at the __________.
- 368.A burned-out LED should be indicated by __________.
- 369.The basic operating principle of a transformer is attributed to __________.
- 370.The output voltage of a 440 volt, 60 Hz AC generator is controlled by the __________.
- 371.Motor controller or starter contacts may become pitted and welded together if the contacts __________.
- 372.Transformer cores are laminated to reduce __________.
- 373.When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an __________.
- 374.The capacity of a storage battery is measured in __________.
- 375.When placed in a magnetic field, which of the materials listed will maintain the highest permeability?
- 376.Before measuring an unknown resistance with an ohmmeter, you should __________.
- 377.The governor control switch of an alternator is moved to the 'raise' position. This action will __________.
- 378.Which of the following statements is true concerning the operating characteristics of a basic squirrel-cage induction motor?
- 379.A transformer in an electric circuit serves to __________.
- 380.As an armature revolves within a magnetic field, friction is developed between the rotated magnetized particles as they pass through each magnetization cycle. This results in __________.
- 381.To test fuses in an energized circuit, you should use a __________.
- 382.The main purpose of an electric space heater installed in a large AC generator is to __________.
- 383.The speed of a squirrel-cage induction motor is determined by the __________.
- 384.Magnetic controller contacts may become welded together during operating conditions as a result of __________.
- 385.When a transformer is used to step down voltage, the low voltage winding is __________.
- 386.The proper way to mix the electrolyte for a battery is to add __________.
- 387.Prior to starting an AC generator prime mover, the voltage regulator selector switch should be placed in the __________.
- 388.A loud buzzing noise at the contacts of a magnetic controller could indicate __________.
- 389.An AC circuit has capacitance arranged in series. If the line voltage remains constant, the capacitive reactance value can be varied by changing the __________.
- 390.The total voltage of a series circuit is the __________.
- 391.When mixing electrolyte for a lead-acid storage battery, __________.
- 392.When securing an AC generator, you should FIRST __________.
- 393.The speed of a squirrel-cage motor is usually changed by __________.
- 394.Excessive humming of AC contactors may be caused by __________.
- 395.Decreasing the frequency in a capacitive circuit while maintaining a constant circuit voltage, will result in a/an __________.
- 396.Caution must be exercised during the charging of lead-acid storage batteries as __________.
- 397.When the current flow through a copper wire increases, its __________.
- 398.Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor?
- 399.The cycles per second developed by the alternator aboard your vessel is determined by __________.
- 400.The counter EMF produced in the windings of a DC motor is 'zero' when the __________.