USCG Electricity – Question Bank Book 12 (BK12) — page 9
1209 questions with correct answers from the official USCG question bank (2008 edition), book 12 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 801.To protect the rotor of a motor disassembled for maintenance or overhaul, it should be __________.
- 802.Ships requiring rapid maneuvering response with a high degree of main propeller shaft control are most often __________.
- 803.Main propeller shaft rotation of a DC diesel-electric ship is normally reversed by __________.
- 804.SCR power converters are used on DC diesel-electric drive ships to __________.
- 805.A four-pole induction motor, operating on three-phase 60 cycle current will operate at approximately __________.
- 806.One major advantage of a diesel electric propulsion plant is __________.
- 807.While standing an "at sea watch" onboard a AC diesel-electric drive ship, you notice that the kwatt load is at roughly 75% of capacity with a power factor less than 1. The reactive power (kvars) in the main power distribution would be __________.
- 808.Propulsion AC generators creating 4160 VAC use transformers to provide 119 volts to the automatic voltage regulator. The turns ratio of this transformer is __________.
- 809.Two AC generators are operating in parallel and both are equipped with automatic voltage regulators. While standing watch, one generator is noted as having a greater lagging kvar value. In order to equalize the kvars between the generators you should __________.
- 810.A conductor with a cross-sectional area of one circular mil would have a diameter of __________.
- 811.An equalizing connection between two compound-wound DC generators when paralleled, serves to __________.
- 812.If a D.C. motor hums, but does not run when energized, which of the listed conditions could exist?
- 813.Thermal strip heaters are provided in DC main propulsion motors to __________.
- 814.An AC diesel-electric propulsion system requires less maintenance than a DC diesel-electric system for which one of the following components?
- 815.Main shaft rotation on an AC diesel-electric propulsion vessel is normally reversed by __________.
- 816.A common method used to control the speed of the AC propulsion motor on a diesel-electric propulsion ship is by __________.
- 817.On electric propulsion drive ships, Silicon-Controlled Rectifiers can be used to control which of the following? I. DC propulsion motors II. AC propulsion motors
- 818.A ships main propulsion electric drive power converter panel circuit breaker may fail to close due to __________.
- 819.The major advantage of a diesel electric propulsion plant is __________.
- 820.An open in the armature of a DC motor is suspected, but is not found by visual inspection of the commutator. The next step in troubleshooting this problem is to __________.
- 821.If a small electric motor is immersed in salt water it should be __________. I. washed in fresh water and thoroughly dried II. initially started with reduced voltage
- 822.An autotransformer is equipped with a 50% tap, a 65% tap, and an 80% tap. Which of the following statements is true concerning a load connected to the 50% tap?
- 823.If a small electric motor is immersed in salt water it should be __________. I. washed in fresh water II. thoroughly dried
- 824.The use of a high wattage soldering iron when soldering or de-soldering components on a printed circuit board may cause which of the following faults to occur?
- 825.When troubleshooting an amplifier, you measure an output of 30 volts. If the gain of the amplifier is 2, what must the input voltage be for the amplifier to work properly?
- 826.If an electric motor fails to start, you should FIRST check the __________.
- 827.Increasing the power source frequency in a capacitive circuit will __________.
- 828.Decreasing the power source frequency in a capacitive circuit will __________.
- 829.Which of the following conditions indicates a short circuited capacitor when checking its condition with an ohmmeter?
- 830.A shorted armature coil in a DC motor can be detected by __________.
- 831.Which of the following precautions should be taken when troubleshooting various power circuits using a VOM multimeter?
- 832.Coast Guard Regulations (46 CFR Part 112) state that a continuous trickle charge, supplied from the ship's service power system, is required for batteries supplying power to the __________.
- 833.Which of the following statements concerning nickel-cadmium batteries is true?
- 834.A battery is connected to a circuit containing three resistors in parallel. The values of the three resistors are 2 ohms, 3 ohms, and 6 ohms. What is the voltage of the battery if the total circuit current is 12 amps?
- 835.When two generators are on the line and are sharing the load equally, they are said to be operating in __________.
- 836.What is the rotor speed of a six pole, 60 cycle, induction motor operating at full load with 3% slip?
- 837.For practical purposes, in a simple series circuit employing two resistors, a drop of one half the source voltage will occur across one resistor if it has __________.
- 838.The formula for computing impedance in a series circuit containing resistance, capacitance, and inductance is __________. [ NOTE: the symbol * stands for 'multiplied by' ]
- 839.For practical purposes, in a simple series circuit employing two resistors, the largest voltage drop will occur across the resistor which has __________.
- 840.Prior to closing the circuit breaker when paralleling two DC generators, you must be certain that the __________.
- 841.A short in the shunt field of a DC motor is best located by __________.
- 842.In a three-wire, 230/115 volt DC system, the potential between neutral and negative is __________.
- 843.The main difference between a motor control circuit containing low voltage protection and low voltage release is that the latter contains __________.
- 844.Which of the following precautions should be taken when troubleshooting various power circuits using an electronic voltage tester?
- 845.Which of the following statements concerning Nickel-Cadmium batteries is true?
- 846.An electrical component is connected across a 120 volt 60 hertz AC supply. What is the current drawn by the component if the impedance is 200 ohms?
- 847.When rolling over a DC main propulsion motor in local emergency or throttle bypass mode, the variable rheostat must FIRST be turned __________.
- 848.Which of the methods listed is used to maintain the division of load between two compound-wound, DC generators operating in parallel?
- 849.Which of the following statements is true concerning the operation of modern marine electric drive DC propulsion motors?
- 850.A carbon resistor operating in electrical equipment that is NOT properly cooled will __________.
- 851.While on watch in the engine room, you are setting up to parallel alternators. The switchboard has a synchroscope and synchronizing lamps. If the synchroscope is broken, which of the steps listed is the most essential before an alternator can be paralleled with the bus?
- 852.While paralleling two alternators, the synchronizing lamps remain lit as the synchroscope pointer approaches the 0°. This would indicate that the__________.
- 853.Which of the following statements is correct regarding the use of a multimeter when directly measuring current?
- 854.A lamp has a source voltage of 110 volts and a current of 0.9 amps. What is the resistance of the lamp?
- 855.Which of the following precautions should be taken when troubleshooting various power circuits using an electronic solenoid type voltage tester?
- 856.Which of the listed conditions might contribute to very rapid wearing of a DC machine's commutator bars?
- 857.With regard to the maintenance of electrical generating machines with pedestal insulated bearings it is important to never __________.
- 858.A coil is wound with 200 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms?
- 859.If a D.C. motor does not run when energized, which of the listed conditions could exist?
- 860.When a megohmmeter is used to test the winding insulation of a large motor, an initial dip of the pointer toward 'zero' is caused by __________.
- 861.What is the significance of having an indicated power factor of 0.8 when describing the output of a generator?
- 862.The term "volt" describes __________.
- 863.A 4160 Volt AC generator is loaded to 2850 kW with a 0.85 power factor. What is the approximate kVAR load on the generator?
- 864.A 120 volt battery is rated at 800 amp-hours for a continuous 50 kW load. Approximately how long will the fully charged battery be able to supply a continuous 50 kW load before the battery rating is exceeded?
- 865.The prime mover of an AC two pole main propulsion generator drives the generator at 3600 RPM. If the main propulsion motor has 80 poles, what will be the propeller speed?
- 866.If the field current of a paralleled AC generator is increased above normal, what will be the net result to the VAR's and power factor?
- 867.When two generators are operating in parallel, what will first occur if the engine driving generator #1 suddenly loses power?
- 868.An AC generator operating in parallel loses its excitation without tripping the circuit breaker. This will __________.
- 869.A coil is wound with 400 feet of No. 16 tinned copper wire and connected to a 12 volt battery. What is the current if the resistance per 1000 feet of No. 16 tinned copper wire is 4.26 ohms?
- 870.The recommended method used to resurface an eccentric DC motor commutator is to __________.
- 871.Sparking at the brushes of a running motor could be an indication of __________.
- 872.Regarding an induction motor, the output power developed is related to the __________.
- 873.While standing an "at sea watch" onboard a DC diesel-electric drive ship you notice the transformer core temperature slowly rising. You should first __________.
- 874.A three-phase alternator operates at 450 volts with a 0.8 power factor. If the ammeter indicates 250 amperes, what should be the KW meter reading?
- 875.The difference between the synchronous speed of a three phase induction motor and its operating speed may be correctly expressed as ________.
- 876.Electrical failures in motors are caused by the breakdown of insulation, which may be caused by __________.
- 877.The safest time to close the ships main switchboard "shore power" circuit breaker would be __________.
- 878.What current is required to light two 75 watt lamps and one 40 watt lamp when connected in parallel to a 120 volt power source?
- 879.Upon failure of the ships normal electrical power supply, the emergency generator should automatically start and supply power to the emergency switchboard through the __________.
- 880.You are in the process of paralleling two AC generators and the synchroscope pointer has stopped at a position other than 0°. This indicates that __________.
- 881.An operational amplifier, as used in today's consoles, has a calculated gain of 5. This means that when the input changes __________.
- 882.Voltage will always lead current in a/an __________.
- 883.What will be the frequency of a three-phase, 16 pole, AC generator operating at 3000 revolutions per minute?
- 884.When testing the rotor of a synchronous motor for short circuits, a low voltage source is applied across the rotor coils through the collector rings. A coil having a short circuit will be indicated by a __________.
- 885.If the synchronous speed of a 12 pole, polyphase, induction motor operating at 60 Hz were 600 RPM, how many poles will be required in a similar motor operating at the same frequency but having a synchronous speed of 900 RPM?
- 886.A magnetic relay is most commonly used to __________.
- 887.If a single-phase induction motor fails to start, the problem may be __________.
- 888.One method of providing an input speed signal for an electric analog tachometer on an engine control panel would be by using a ________.
- 889.A load is connected to the secondary of a power transformer and the current through the load is 10 amps. If the transformer has a step-up ratio of 10 and the input voltage to the primary is 110 VAC, what will be the current flow through the primary?
- 890.When charging a 100 amp-hour lead-acid battery, __________.
- 891.A 125 volt DC motor is rated at 10 kW. What is the current rating of the motor?
- 892.The difference between the synchronous speed of an three phase induction motor and its operating speed is called slip and may be correctly expressed as _________.
- 893.A four-pole, 60 cycle, squirrel-cage motor has a full load speed of 1725 RPM. What will be the percent of slip at full load?
- 894.Which of the meters listed should only be used after a circuit has been electrically de-energized?
- 895.A single-phase induction motor starts, comes up to about 75% rated speed, slows down to a lower speed, and accelerates again. The problem is most likely in the __________.
- 896.The circuit power factor of an AC generator operating singularly is determined by the __________.
- 897.When a fluorescent lamp has reached the end of its useful life, it should be replaced immediately, or the resultant flashing may __________.
- 898.Voltage generated by modern revolving field AC generators is fed to the bus by means of __________.
- 899.Engine RPM can be indicated on a engine control panel by measuring the voltage from a ________.
- 900.Capacitors are commonly used on power supply circuits for engine room automation consoles to __________.