USCG Electricity – Question Bank Book 12 (BK12) — page 5
1209 questions with correct answers from the official USCG question bank (2008 edition), book 12 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 401.A loud buzzing noise coming from the contacts in a magnetic controller can be caused by __________.
- 402.While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is __________.
- 403.The specific gravity of the electrolyte in a lead-acid battery is measured by a __________.
- 404.The frequency of an AC generator is adjusted by means of the __________.
- 405.The function of the commutator in a DC motor is to __________.
- 406.Humming or buzzing of electric contacts is a symptom of __________.
- 407.Capacitance in an AC circuit will __________.
- 408.An ohmmeter used to test for front-to-back resistance of a PN junction diode should produce roughly what ratio?
- 409.Which of the following activities occurs during the charging process of a lead-acid storage battery?
- 410.In a simple DC circuit, the resistance is held constant while the applied voltage is halved. Current flow, therefore, will __________.
- 411.When measuring AC current flow, you must always connect the meter __________.
- 412.To increase the frequency of an operating AC generator, you should __________.
- 413.The counter EMF of a DC motor is maximum when the __________.
- 414.Which of the following characteristics is most critical in determining the size of the cable to be used in a particular circuit?
- 415.To conduct an in-circuit test of a transistor, you should use a/an __________.
- 416.The specific gravity of the electrolyte solution in a lead acid battery __________.
- 417.In the flow of one cycle of single phase AC current past any given point in a circuit, the maximum current peak occurs __________.
- 418.AC and DC generators are similar in that they __________.
- 419.Shunt, series, and compound wound motors, are all DC motors designed to operate from __________.
- 420.Motor starter or controller contacts may become welded together if the contacts __________.
- 421.Which of the following statements concerning copper wire sized by AWG numbers is correct?
- 422.Normally, the FIRST step in troubleshooting a transistor circuit card is to __________.
- 423.During discharge of a lead-acid storage battery, which of the following actions occurs?
- 424.If the length of a wire is halved and the cross-sectional area is doubled, the resistance will be __________.
- 425.Prior to taking a resistance reading with a volt-ohm-milliammeter, the 'zero' setting must be adjusted. After clipping the two leads together, you find the adjustment knob will not return the pointer to 'zero'. This is most likely an indication of __________.
- 426.Which of the following devices are protected from being motorized by a reverse-power relay?
- 427.An advantage of DC motors over AC motors is that they __________.
- 428.If many turns of an alternating current coil for a contactor become short circuited, the coil __________.
- 429.Relative to the secondary winding of a step-up transformer, the primary winding will have __________.
- 430.Before using a volt-ohmmeter to measure resistance readings, you should __________.
- 431.To equalize the power factor of two alternators operating in parallel, the __________.
- 432.Which of the following operating characteristics for DC motors is considered to give high starting torque?
- 433.If a magnetic controller contactor fails to pick up when the coil voltage is applied to the contactor coil, the cause may be __________.
- 434.The total power used up in a series circuit is __________.
- 435.When the operating handle of a molded-case circuit breaker is in the mid-position, this indicates that the circuit breaker is __________.
- 436.When you check the specific gravity of the battery electrolyte with a hydrometer, it should be kept in mind that __________.
- 437.The total resistance of a parallel circuit is always __________.
- 438.Equal power factors on paralleled AC generators are maintained by an automatic __________.
- 439.If a magnetic controller contact fails to pick up when the operating coil is energized, one possible cause may be __________.
- 440.Which of the listed forms of water should be added to a lead-acid battery?
- 441.If the resistance of a circuit is cut in half and the applied voltage is kept constant, the current flow will be __________.
- 442.The power factor at which a paralleled AC generator operates is usually adjusted by the __________.
- 443.Which of the processes listed occurs during the charging of a lead-acid storage battery?
- 444.The primary function of an electric motor is to __________.
- 445.Current measuring instruments must always be connected in __________.
- 446.If the excitation is increased to one of two alternators operating in parallel, the __________.
- 447.In a series wound motor, the current passing through the field windings is also passing through the __________.
- 448.Which of the listed devices may be installed on a large diesel-electric alternating current propulsion generator?
- 449.The total power consumed in a parallel circuit is __________.
- 450.The resistance of electric wire will decrease as its __________.
- 451.Which of the instruments listed is generally connected in series in the circuit?
- 452.The speed of a series wound winch motor is controlled by __________.
- 453.The arc resulting from the tripping of a circuit breaker is prevented from damaging the contacts by __________.
- 454.When a lead-acid battery begins gassing freely while receiving a normal charge, the charging current should __________.
- 455.When the voltage remains constant and the resistance is increased in a series circuit, the flow of current __________.
- 456.An ammeter should be used to measure __________.
- 457.Why is it desirable to operate paralleled AC generators at the same power factor?
- 458.The charge of a lead-acid battery is checked with a __________.
- 459.When the voltage remains constant, and the resistance increases in a series circuit, current flow __________.
- 460.A DC ammeter is always connected __________.
- 461.The voltage output of an AC generator is accurately controlled by __________.
- 462.You can determine if a circuit breaker has tripped by __________.
- 463.An operational amplifier, as used in today's consoles, may have a calculated gain of 5. This means that as the input changes by __________.
- 464.Under which of the following conditions will a lead-acid battery be given a 'test discharge'?
- 465.Which of the formulas listed is correct for determining power?
- 466.Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement?
- 467.Which of the following statements describes what will happen when both the polarity of the field poles, and the direction of current to the brushes of a DC motor are reversed?
- 468.A slow continual loss of electrolyte level from one cell of a storage battery could be due to __________.
- 469.Nickel-cadmium batteries are superior to lead-acid batteries at high discharge rates because they __________.
- 470.When the operating handle of a molded-case circuit breaker is in the mid-position, the circuit breaker is indicated as being __________.
- 471.When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because __________.
- 472.The rate at which heat is produced in a direct current circuit is equal to __________.
- 473.Which of the following represents a characteristic of an ungrounded electrical distribution system?
- 474.What is the approximate voltage per cell produced by the nickel-iron (Edison) battery?
- 475.One horsepower is equal to __________.
- 476.An ammeter reads slightly above 'zero' when its leads are disconnected, this is a result of __________.
- 477.When an alternator is to remain idle for even a few days __________.
- 478.Proper storage battery maintenance includes __________.
- 479.Part of the insulation of practically all electrical machinery is in the form of organic compounds which contain some amount of __________.
- 480.When the current in a power transmission line is increased, the power loss __________.
- 481.Modern handheld non-contact digital tachometers operate by counting light pulses returned to the unit by __________.
- 482.To determine the state of charge of a nickel-cadmium battery, you would use a/an __________.
- 483.The true power indicated by the pointer movement of a wattmeter depends on the current flow through the load, the magnitude of the potential across the load, and the __________.
- 484.The shunt of a DC ammeter should be connected in __________.
- 485.The standard method of controlling the output voltage of a 440 volt, 60 Hz, AC generator is accomplished by adjusting the __________.
- 486.Common nickel-cadmium and nickel-iron storage batteries utilize __________.
- 487.Due to the operating characteristics of the system, time lag fuses (or dual-element fuses) are necessary for use in __________.
- 488.Loss of residual magnetism in an alternator or generator can be corrected for by __________.
- 489.An accidental path of low resistance which passes an abnormal amount of current is known as a/an __________.
- 490.A milliammeter, with a full scale deflection reading of 100 milliamps, is known to have an accuracy of plus or minus 2%. A meter reading of 10 milliamps would indicate a line current of between __________.
- 491.Which of the following materials is a good electrical insulator?
- 492.Cleaning of electrical insulation should be __________.
- 493.The plates of a wet cell NiCad storage battery are made of __________.
- 494.An "instantaneous-trip" type fuse will __________.
- 495.Basic electrical motor action depends on __________.
- 496.When mixing electrolyte, which of the following precautions should always be observed?
- 497.Which of the following statements about copper wire sized by the AWG rating is correct?
- 498.Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading?
- 499.Relative to the direction of rotation, a D.C. motor commutating pole has the same polarity as the __________.
- 500.One method of troubleshooting digital circuits in a console is to __________.