USCG Electricity – Question Bank Book 12 (BK12) — page 7
1209 questions with correct answers from the official USCG question bank (2008 edition), book 12 (Engine – USCG question bank, 2008 edition, Engine officers). Pass mark 70%. Click a question to see its answer.
Take the full practice test →Free USCG practice test with the real pass mark, no sign-up- 601.The most practical way to control the voltage output of an AC generator is to vary the __________.
- 602.Which of the instruments listed could be use to locate a grounded field coil in a synchronous motor?
- 603.You are attempting to parallel two AC generators and the synchroscope pointer stops at a position other than 0°. If you close the circuit breaker at this moment __________.
- 604.What type of electric motor is commonly used to start small auxiliary diesel engines?
- 605.Violent gassing developed by a lead-acid battery during charging indicates that the __________.
- 606.One important difference between wye-connected and delta-connected generators is that delta connections have __________.
- 607.You are attempting to parallel two AC generators, and the synchroscope pointer is revolving fast in the clockwise direction. This indicates that the frequency of the incoming machine is __________.
- 608.A 'dielectric' is a/an __________.
- 609.All of the following items can be used in the maintenance of a D.C. propulsion motor's commutator face EXCEPT __________.
- 610.A reverse-power relay will prevent AC generator motorization by __________.
- 611.When a battery is continuously exposed to low temperatures, the best procedure to keep it from freezing is to __________.
- 612.A galvanometer is an instrument used to measure __________.
- 613.Complete AC motor controller maintenance includes __________.
- 614.If a unloaded DC compound motor's shunt field were weakened by rheostat resistance or by an open circuit, the motor would __________.
- 615.The purpose of the reverse power relay, provided on a ship's service alternator panel, is to trip the circuit in the event of __________.
- 616.Which of the following conditions indicates that a lead-acid battery is being charged too rapidly?
- 617.A device which can be used to check the calibration of a circuit breaker is a __________.
- 618.Propulsion DC motor brush pressures can be calculated by __________.
- 619.How is a wattmeter electrically connected in a circuit?
- 620.The dielectric strength of a vacuum or dry air is approximately __________.
- 621.The operating torque of the upper induction disc-type element, or timer element, of an AC reverse power relay is obtained from __________.
- 622.Which of the following statements represents the action of a megohmmeter when testing a small capacitor in good condition?
- 623.A wattmeter is used to determine __________.
- 624.Which of the following statements is true concerning a step-down transformer in an operating AC power circuit?
- 625.When a megohmmeter is used to test the insulation of a large motor, the initial dip of the pointer toward 'zero' is caused by __________.
- 626.Which of the listed transformers uses a single winding to produce voltage transformation?
- 627.A capacitor is to be tested with a megohmmeter. If the meter is connected to a shorted capacitor, the meter pointer should __________.
- 628.The RPM of an AC generator can be measured with a/an __________.
- 629.The 'dielectric constant' is a numerical value indicating the effectiveness of a dielectric material in comparison to that of a standard, which is __________.
- 630.The air gap in an induction motor should be periodically checked with a feeler gage to prevent possible __________.
- 631.The hook-on AC volt-ammeter consists essentially of a split-core and a rectifier-type instrument connected to the secondary winding of a __________.
- 632.Which type of flux should be used when soldering electrical wire connections for electronic components on printed circuit boards?
- 633.If the pointer of the synchroscope is rotating in the slow direction (counterclockwise) as you are preparing to parallel two alternators, the __________.
- 634.The air gap in an induction motor should be checked periodically with a feeler gage to detect __________.
- 635.A shore power circuit breaker should be closed only __________.
- 636.When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide __________.
- 637.An internal resistance is placed in series with the meter movement of which of the following instruments?
- 638.When paralleling two alternators using three synchronizing lamps, the flickering of all three lamps becomes progressively slower and slower. This means the __________.
- 639.The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END AFT END Top .045 .049 Right Side .045 .047 Left Side .045 .047 Bottom .045 .041 Which of the following statements is true?
- 640.The 'dielectric constant' of dry air or a vacuum is __________.
- 641.You can determine if a circuit breaker is tripped by __________.
- 642.Proper maintenance of a D.C. motor's commutator includes __________.
- 643.AC voltmeters are generally calibrated to read the __________.
- 644.When paralleling two AC generators, the synchroscope selector switch and frequency meter switch should be set up to sense the frequency of the __________.
- 645.When the operating handle of a molded case circuit breaker is in the mid-position, it indicates the circuit breaker is __________.
- 646.If there is a reduction in the normally supplied frequency to a 120/240 volt, three-phase AC current motor from 60 hertz to 55 hertz, the motor would __________.
- 647.Which of the following electric meter movements uses a stationary permanent magnet and movable coil?
- 648.If a small electric motor has been submerged in saltwater for a short period of time, you should __________.
- 649.In a three-phase, open-delta connected transformer, the line current is equal to __________.
- 650.Most AC voltmeters are calibrated to indicate __________.
- 651.When paralleling two alternators the synchronizing lamps grow dim and are totally darkened as the synchroscope pointer approaches the 0° position. This indicates the __________.
- 652.D.C. motor brush adjustment includes attention to __________.
- 653.One of the generator or motor bearings is generally insulated from the end housing in order to prevent __________.
- 654.To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an __________.
- 655.Encrusted dirt accumulated inside a motor should be removed with a __________.
- 656.If all three ground-detection lamps continue to burn at equal intensity after the test button is depressed and released, which of the listed conditions is indicated?
- 657.One of the generator bearing shells is generally insulated from the end housing in order to prevent __________.
- 658.Electrostatic forces in high voltage circuits cause indicating instruments to give __________.
- 659.If a circuit breaker that utilizes built-in, current limiting fuses (CLF's) cannot be closed, the problem may be traced to __________.
- 660.To check the three line fuses of a three-phase system consisting of a three-phase motor, you must __________.
- 661.If the voltage applied to a moving disk frequency meter decreases, while the applied frequency remains the same, the frequency indication will __________.
- 662.You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should __________.
- 663.When paralleling two alternators, the synchronizing lamps remain lit as the synchroscope pointer approaches the 0°. This indicates the __________.
- 664.Which of the following procedures should be used to maintain a large electric motor during periods of inactivity?
- 665.When replacing a defective transformer in a paralleled transformer configuration, which of the following actions must be carried out to insure proper operation of the equipment it serves?
- 666.Which of the listed conditions could indicate the need for cleaning electrical insulation?
- 667.The reactive power drawn by a motor from an AC generator is the power which is __________.
- 668.A multimeter may be damaged by taking a __________.
- 669.When two AC generators are being paralleled, the breaker should be closed with the synchroscope pointer rotating in the __________.
- 670.The speed of a synchronous motor is varied by __________.
- 671.When working on electrical circuits containing large capacitors, in addition to de-energizing the circuit, which of the listed precautions should also be taken?
- 672.The most inefficient method of voltage reduction, from the standpoint of power loss, even when placed in series with the load, is the use of a/an __________.
- 673.When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and __________.
- 674.If two AC generators have just been placed in parallel, the kilowatt load is initially distributed evenly by __________.
- 675.Which of the following types of insulation will begin to deteriorate FIRST as a result of the heat generated in the conductor it surrounds?
- 676.Seating the brushes on a D.C. motor is first accomplished using __________.
- 677.Which of the following statements regarding the use of a current measuring instrument is correct?
- 678.How many possible states does a binary logic circuit have?
- 679.A multimeter (Simpson) can be used to measure __________.
- 680.The KW load is evenly distributed between two alternators operating in parallel by adjusting __________.
- 681.Which of the following problems will most likely occur if the starting winding of a split-phase induction motor failed to cutout once the motor was in continuous operation?
- 682.When insulation failure produces a low resistance current path between two conductors, the resulting condition is known as __________.
- 683.Which of the listed pairs of materials make the best insulators?
- 684.In a logic circuit, the NOT gate function __________.
- 685.Before using an all-purpose electric measuring instrument (multimeter) utilizing internal batteries to supply power for resistance measurements, you should FIRST __________.
- 686.When paralleling two AC generators, the frequency of the incoming machine immediately prior to closing its breaker should be __________.
- 687.A single-phase induction motor fails to start. The rotor is spun rapidly with the line switch closed. Having started by this method it is noted that the motor fluctuates between a very slow speed and half speed. The problem probably lies in the __________.
- 688.When disassembling electric motors for maintenance or overhaul, __________.
- 689.In a logic circuit the NOR and NAND gate functions __________.
- 690.Conductor resistance may be INDIRECTLY measured by using a/an __________.
- 691.If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the __________.
- 692.The true power indicated by a wattmeter depends on the current flow through the load, the magnitude of the potential across the load, and the __________.
- 693.When paralleling two AC generators, the frequency of the machine coming on-line, immediately prior to closing its breaker, should be __________.
- 694.A three-phase, squirrel cage, induction motor will run hot due to __________.
- 695.The ground indicating light on the main electrical switchboard is indicating a ground. The best procedure for locating the grounded circuit is to __________.
- 696.D.C. propulsion motor brush pressure depends on the brush grade used and in practice is set with a __________.
- 697.The unit 'hertz' is equivalent to __________.
- 698.The kilowatt load can be adjusted on a paralleled generator by using the __________.
- 699.A three-phase, squirrel cage, induction motor will run hot due to a/an __________.
- 700.Which of the listed pairs of materials make the best insulators?