F4 Marine Engineering — Management Level — Page 6
704 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 501.For the selection of steam turbine bearings, a preliminary calculation is made according to:
- 502.When is a turbine main bearing operating normally?
- 503.The operating modes of marine steam turbines depend on:
- 504.What does the power of a steam turbine depend on?
- 505.We have а throttle governing of the steam turbine when:
- 506.The governing of a steam turbine in which steam is supplied not only to the first stage, but also to the later stages is called:
- 507.What is the percentage of the power output of the astern turbine compared to the main ahead turbine?
- 508.In general, where are the astern stages of steam turbines placed?
- 509.Could there be a direct connection between the turbine shaft and the propeller?
- 510.When does compression actually start in four-stroke marine diesel engines?
- 511.In what limits varies the polytropy index of compression in low-speed marine diesel engines?
- 512.What does the polytropy index of the compression process depend on?
- 513.Why the compression ratio "ε" in marine diesel engines should not be higher than 18-20?
- 514.State which is the correct definition of the combustion process?
- 515.How is the fractional composition of the fuel expressed?
- 516.State what are the main elements of diesel fuels?
- 517.What is the difference between the chemical composition of gasoline and diesel fuels?
- 518.Why in the records of some of the chemical elements after the notation there is the number 2?
- 519.Give the correct equation for the chemical reaction of the oxidation of carbon:
- 520.Is it possible to plot a speed limit curve of marine Main Engine :
- 521.Is it possible to plot a speed curve of marine Internal combustion engine vs the smoke limit:
- 522.Is it possible to plot a maximum speed curve of Marine Internal combustion engine:
- 523.What is the requirement for taking nominal speed curve of Marine Internal combustion engine:
- 524.Which points of the rated speed curve of the Marine Internal combustion engine are acceptable for continuous operation:
- 525.Why is it not permissible to operate the Marine Internal combustion engine for a long time at points of the rated speed curve at a lower rotational speed than the rated one:
- 526.Why is it not permissible to operate Marine Internal combustion engine for a long time at points of the rated speed curve at higher rotational speed than nominal:
- 527.Which load curve can be used to determine the mechanical losses of Marine Internal combustion engine:
- 528.Marine Internal combustion engine working with a variable pitch propeller works on:
- 529.Futher opening of the compensation needle of the governor leads to:
- 530.How are a diesel generator/DG/ and a turbogenerator/TG set up for parallel operation?
- 531.The concept "Main Engine (ME) working mode " means:
- 532.The working mode of the Main Engine (ME) is considered to be "optimal" when:
- 533.Which of the listed indirect indicators most accurately reflects the power developed by Marine internal combustion engine?
- 534.What method of regulation of the amount of fuel is achieved with the high pressure fuel pump of the Main Engine (ME) equipped with Variable injection timing (VIT) system?
- 535.Marine internal combustion engine controlled by a mechanical all-speed governor with a load limiter and operating on a heavy propeller curve, if when setting a certain rotational speed, cannot reach it, its operating point is located on:
- 536.Marine internal combustion engine, controlled by a mechanical all-speed regulator without a load limiter and operating on a heavy propeller characteristic, if when setting a certain rotational speed it cannot reach it, its operating point is located on:
- 537.The turbine blades in turbocharger units are made of:
- 538.In steam boilers there is a risk of low-temperature corrosion of:
- 539.What is the cause of scale deposits in a steam boiler?
- 540.The capacity regulation of mechanical non-adjustable centrifugal burners in steam boilers in a wider range is done by:
- 541.Boiler water hardness is mainly due to:
- 542.The largest amount of salts in the water system of the boiler are contained in:
- 543.What is the purpose of the deaerator in the boiler feed water system?
- 544.Which of the following statements regarding water tube and fire tube boilers is true?
- 545.Which of the following statements describes the mechanism of a chemical process that takes place in the water during boiler operation?
- 546.What quality should the feed water have for normal operation of the boiler?
- 547.Why is it important to maintain the pH of the condensate of the boiler system within the permissible limits?
- 548.If the water level cannot be seen at the bottom of the boiler sight glass, which of the following actions should be taken immediately?
- 549.Can the mechanical loss coefficient /mechanical efficiency/ be used to switch from indicated to effective "P" parameters at all "n"?
- 550.Which high-tech materials have similar qualities and applications?
- 551.Which curve of Marine internal combustion engine diagram do we determine as speed curve?
- 552.Which statement is not true about propeller curves?
- 553.What is the permitted overspeed of the engine for sea trials under ballast?
- 554.By which relatively constant curve are obtained the operating points of the ship propulsion system when the propeller is with fixed pitch?
- 555.By which relatively constant curve are obtained the operating points of the propulsion system when the propeller is with variable pitch, without speed governor?
- 556.What is the purpose of the fuel separation process for Marine Internal combustion engines ?
- 557.The flash point of the marine fuel for Marine internal combustion engines must be used to determine:
- 558.The appearance of an emulsion in the Marine internal combustion engines lube oil system leads to:
- 559.Which hydrocarbon group provides the minimum self-ignition delay period for diesel fuels?
- 560.The motor properties of diesel fuels are determined by:
- 561.Lubricating properties of lube oils depend on:
- 562.The viscosity index of the lube oil means:
- 563.The temperature of the refrigerant in the evaporator depends on:
- 564.Which of the following effective parameters can be obtained by direct measurement?
- 565.Under what conditions is the load curve obtained?
- 566.A sudden drop in pressure in a steam boiler can lead to:
- 567.What is the purpose of the thermo- regulating valve of the refrigeration plant?
- 568.How should be installed the vapor-filled sensor bulb of the thermo-regulating valve?
- 569.Substances that oxidize cast iron, remove gases and have a beneficial effect on graphitization are called:
- 570.The chemical elements that are always found in the composition of steels are:
- 571.The most important element in steels is:
- 572.Which of the following chemical elements are harmful to steels?
- 573.What is the treatment of steels called, in which they are heated to a certain temperature for a strictly defined time, held at that temperature and cooled at a certain rate?
- 574.The process of removing internal stresses and improving the strength properties of steels is called:
- 575.What is the purpose of the annealing process in steels?
- 576.The chemical-thermal treatment consisting in enriching the surface layer of steels in order to improve their mechanical properties is called:
- 577.The process of prolonged heating of the steels /from 20÷80 hours/ at temperatures 480 ÷ 5,600 ºС in ammonia is called:
- 578.The process of simultaneous enrichment of the surface layer of steels with carbon and nitrogen is called:
- 579.In a pressure charging sytem with turbocharger and electrically-driven auxiliary centrifugal compressor, what is the most critical moment of surging?
- 580.In a pressure charging sytem with two turbochargers operating in parallel, one is contaminated. Which of the two is more at risk of surging?
- 581.On which types of ships are most often installed double-circuit steam boilers and why?
- 582.How will you define the concept " Straight-flow steam boiler with multi-pass circulation equal to unity "?
- 583.How is the heat output of the boiler measured?
- 584.The ratio of the amount of heat usefully used in the boiler, which is determined by the complete combustion of the fuel consumed for this time interval, is called:
- 585.The ratio of the amount of water that passes through the circuit to the steam generating capacity of the boiler for a certain time interval is called:
- 586.What happens when water circulation is disturbed in the Marine steam boiler?
- 587.What is the purpose of the screen pipes in the water tube marine steam boiler?
- 588.The introduction of an additional circuit in the steam boiler is done in order to:
- 589.In fire tube marine steam boilers, the exhaust gases move along:
- 590.What type of circulation do fire tube boilers have?
- 591.The boilers that use the heat of the exhaust gases of the Marine internal combustion engines are called?
- 592.What happens if the pressure in the boiler is suddenly reduced?
- 593.Which boilers have the greatest steam generating capacity, with equal indicators?
- 594.The place where water, steam and steam-water mixture is collected and distributed along the heating tubes is called:
- 595.The system in the boiler, through which excess salts are removed from the boiler is called:
- 596.What are the marine steam boilers attached to the ship hull with.
- 597.a Main Marine internal combustion engine , controlled by an electronic governor with the possibility of setting the limiting curve and working on a heavy propeller curve, if when setting a certain rotational speed, it cannot reach it, its operating point is located on:
- 598.What is the maximum allowable continuous operating rotational speed of the main engine when working on a light propeller curve?
- 599.What is the maximum allowable continuous operating rotational speed of the main engine when working on a heavy propeller curve?
- 600.At what propeller curves the Main Engine has a power reserve: