F4 Marine Engineering — Management Level — Page 4
704 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 301.How does the heat stress of Marine diesel engine change with an increase in the excess air ratio?
- 302.At what excess air ratio do modern marine main engines operate at rated power:
- 303.Why is the excess air ratio in modern marine main engines high at rated power:
- 304.What should be measured to determine the indicated efficiency in ship conditions?
- 305.How does the indicated efficiency of the Marine diesel engine (MDE) change as the excess air ratio increases to about 3?
- 306.How does the indicated efficiency of the Marine diesel engine (MDE) change as the excess air ratio increases from approximately 3.5 upwards?
- 307.How does the indicator efficiency of the Marine diesel engine (MDE) change with a reduction in the duration of combustion:
- 308.How does the indicator efficiency of the Marine diesel engine (MDE) change when combustion starts earlier:
- 309.What should be measured to determine in ship conditions the effective efficiency of the Marine diesel engines (MDE):
- 310.How does the effective efficiency of the Marine diesel engine (MDE) change as the excess air ratio increases to about 3?
- 311.How does the effective efficiency of the Marine diesel engine (MDE) change as the excess air ratio increases from approximately 3.5 upwards?
- 312.How does the effective efficiency of the Marine diesel engine (MDE) change with a decrease in the duration of combustion?
- 313.How does the effective efficiency of modern main Marine diesel engines (MDE) change when combustion starts earlier?
- 314.The reduction of the maximum fuel injection pressure when operating the main Marine diesel engines (MDE) in maneuvering modes is due to:
- 315.What is the maximum temperature range of the piston crowns in Marine diesel engines (MDE) at nominal operating mode?
- 316.The opening of an automatic starting valve of Marine diesel engines (MDE) is carried out by the:
- 317.Flow regulators for fluids serve to:
- 318.The starting valve with an angle-divider balanced characteristic opens when:
- 319.The effect of counterair supply during maneuvering is best in:
- 320.Crankshaft deflection of the Marine diesel engines (MDE) gives information about:
- 321.To which main type of characteristics does the limit characteristic of Marine diesel engines (MDE) belong:
- 322.What is the limiting characteristic of Marine diesel engines (MDE) according to the maximum permissible load for continuous operation?
- 323.How long can the Marine diesel engine (MDE) work continuously at a point located on the limiting characteristic according to the maximum permissible load for continuous operation:
- 324.How the HPFP of the distributing type meters the amount of fuel to be injected when the engine is running?
- 325.The main purpose of the discharge valve of the HPFP of marine diesel engines is:
- 326.Unlike the exhaust valves, the intake valves of some Marine diesel engines may be made of low-alloy steel because:
- 327.With a PGA type of governor, when using oil with a viscosity other than that recommended by the manufacturer, it is necessary:
- 328.The tendency of diesel fuels to ignite /with normally operating fuel equipment/ is caused by:
- 329.The cooling of the air after the turbocharger units results in:
- 330.The bearings in the compressor side of the VTR series turbocharger units are:
- 331.Could the surging be the result of causes outside the turbocharger unit?
- 332.Which pressure charging system has a higher efficiency on the turbine side?
- 333.The turbine wheels used in turbocharger units are:
- 334.When replacing a nozzle unit, should the modification of the turbocharger be known?
- 335.Which of the following fluids has the highest density?
- 336.Which of the following fluids has the lowest density?
- 337.Chlorine is added to the cooling fresh water of marine ICE to:
- 338.Insufficient cooling water for the refrigeration condenser will result in:
- 339.The main purpose of the marine steam boiler superheater vent valve is to:
- 340.Which statement about sealing rings for sealing the water space of cylinder liners is not true?
- 341.Marine ICE safety valves are mandatory for cylinder bores equal to and greater than:
- 342.The exhaust gas temperatures of a four-stroke Marine ICE engine:
- 343.Which of the following can cause the temperature in the refrigerator to rise?
- 344.The first two digits from right to left of the main designation of the rolling bearings determine:
- 345.Which of the following types of speed governors does not have a regulating function, but only protects the engine from overrun?
- 346.Which of the listed bearings are most widely used as main and flywheel bearings in Marine ICE?
- 347.The expansion tank in a closed loop freshwater cooling system is designed to maintain a constant system pressure and:
- 348.Which of the following methods is commonly used to lubricate the bearings of a Marine ICE?
- 349.If the color of the surface layer of the main bearing white metal is black and has increased hardness, with scratches on the crankshaft journal, what is the likely cause?
- 350.What effect does the increased concentration of calcium in the boiler water cause?
- 351.What is the most likely cause of overheating of the main bearings?
- 352.Which of the following principles does not apply to heat transfer in a marine steam boiler?
- 353.Special periscopes in the boilers are installed to observe:
- 354.Which of the statements is Carnot's theorem?
- 355.Which of the following physical processes is used to produce cold in a compressor freon refrigeration system?
- 356.The condensation temperature of the refrigerant mainly depends on:
- 357.Refrigerant supercooling causes:
- 358.Natural supercooling takes place in:
- 359.Refrigerant vapor overheating:
- 360.If the overheating of the refrigerant vapor in the refrigerating chamber is increased with a direct connection between the evaporator and the compressor, the evaporation temperature:
- 361.The cooling ratio is:
- 362.Which of the following thermodynamic processes is not included in the theoretical cycle for a real compressor freon refrigeration system?
- 363.In pressure charged Marine ICE, the parameters used to denote the fresh charge are:
- 364.What does the coefficient of residual gases in Marine ICE indicate?
- 365.What heats the fresh charge of air when it enters the cylinder of a Marine ICE with turbocharger?
- 366.What is the temperature of the working medium at the end of the pressure charging process in two-stroke pressure charged Marine ICE?
- 367.Degree of compression in Marine ICE is called the ratio between the volumes:
- 368.Under "degree of pressure increase" "λ" in Marine ICE we understand the relationship between:
- 369.The use of heat in the ideal cycle is characterized by:
- 370.The cycle of Otto Beau de Roche is a cycle of gasoline Marine ICE. It is characterized by:
- 371.On which thermodynamic cycle do low-speed Marine ICEs work?
- 372.Why is vapor freon topping up recommended?
- 373.In a wet sump ICE oil system, the oil pressure in the system is usually:
- 374.In the high pressure oil system of Marine ICE the number of oil pumps is most often:
- 375.The pumps in the high pressure oil system of Marine ICE are called:
- 376.The main bearings of the Marine ICE are lubricated by the oil system through:
- 377.The oil temperature in the low-pressure oil system of a crosshead Marine ICE is:
- 378.Marine ICE oil filters are:
- 379.The purpose of the separators in the Marine ICE oil system is:
- 380.The presence of water in the oil in the system of ICE leads to:
- 381.Is the lubricator system mandatory for crosshead main engine?
- 382.The purpose of the lubricator pump in Marine ICE is:
- 383.The lubricator pump in a crosshead engine is:
- 384.The telescoping pipe connection in some crosshead engines serves to:
- 385.When is compressed air supplied to the cylinder when starting the main engine?
- 386.How is compressed air supplied for starting the main engine?
- 387.Are four-stroke ICE's started with compressed air?
- 388.At what time when starting Marine ICE is fuel injected?
- 389.What is the compressed air pressure in the air cylinders?
- 390.What should be the environmental conditions in order for the Marine ICE to work for an unlimited time at a point located on the limiting characteristic of the maximum permissible load for continuous operation:
- 391.Can the operating point be located above the limiting characteristic of the maximum permissible load for continuous operation, if the Marine ICE has a mechanical regulator with a load limiter:
- 392.The load limiter built into the mechanical speed governor of Marine ICE limits the operation of the engine to:
- 393.Who should limit the operation of the Marine ICE in the short-term overload area?
- 394.Who should limit the operation of the Marine ICE in the area of permissible excess of RPM?
- 395.Which of the indicated powers of modern Marine ICE is the greatest?
- 396.Where is fuel and air mixed in diesel engines?
- 397.At what movement of the piston does the compression of the working media in Marine ICE take place?
- 398.What is the purpose of the compression in Marine ICE?
- 399.What would an excessive rise in temperature at the end of the compression lead to in carbureted ICE?
- 400.How will a vortex movement of the air affect the quality of the compression process in Marine ICE?