F4 Marine Engineering — Management Level
704 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 1.With a steady mode of operation of the Main MDE connected directly to a propeller, the operating points can be located:
- 2.In the case of transient mode of operation of the Main MDE connected directly to a propeller, the operating points can be located above the bollard pull line:
- 3.When reversing a Main MDE with counter air from ahead to astern, fuel is supplied to the cylinders when:
- 4.When reversing a Main MDE with counter air, from ahead to astern if the line of constant speed of the ship on which the reversal begins crosses the power limit line at RPM lower than the minimum sustainable
- 5.Reversing of the Main MDE with counter air, from ahead to astern must begin:
- 6.What determines the portion of fuel per cycle/the height of the useful plunger stroke/ in the HPFP of the distribution type /BOSCH type/ for MDE?
- 7.Which of the following cross-section profiles of supporting beams has the largest moment of inertia?
- 8.With incorrect setting of the engine indicator drive, the length of the indicator diagram:
- 9.With correct setting of the engine indicator drive, if the fuel supply to the MDE cylinder stops:
- 10.With correct setting of the engine indicator drive,, if the fuel supply to the MDE cylinder is stopped, the mean indicated pressure is:
- 11.At a constant load with an increase in the RPM, the mechanical efficiency of a main low-speed engine:
- 12.An indirect indicator of the concept of "load" of MDE can be:
- 13.How the indicated engine efficiency changes when the fuel supply pressure after opening the fuel valve is higher than normal:
- 14.The mean fuel pressure at late fuel injection for a modern marine main engine:
- 15.With constant cycle portion of fuel, which of the following increases the most with increasing the RPM?
- 16.With a constant cycle portion with increasing RPM, which phase of combustion changes the most measured as per crankshaft angle of rotation?
- 17.When changing the first phase of combustion delay of self-ignition), which of the indicated parameters changes the most
- 18.At a constant rotational speed with an increase in the cycle fuel portion, which of the following phases of combustion does not change?
- 19.What is usually the cause of corrosion of MDE bearings:
- 20.If the RPM of the Marine ICE and the beginning of fuel supply is constant, with an increase in the cetane number of the fuel, the mechanical stress:
- 21.What is the main form in which combustion develops during its second phase in Marine ICE:
- 22.What is the main form in which combustion develops during its third phase in Marine ICE:
- 23.What is the main form in which combustion develops during its fourth phase in Marine ICE:
- 24.What is the reason for the specific noise of diesel engine operation?
- 25.The area of the closed normal indicator diagram of Marine ICE corresponds to
- 26.The mean indicated pressure in Marine ICE:
- 27.Which of the following indicators can be used to determine the effective power of the marine ICE more precisely:
- 28.Most precisely, the effective power of the marine ICE is determined by:
- 29.The mean indicated pressure of early fuel supply for a modern marine main engine:
- 30.The mean indicated pressure of late fuel supply for a modern marine main engine decreases as much as …..... decreases:
- 31.The mean indicated pressure of early fuel supply for a modern marine main engine increases as much as ….... increases:
- 32.The mean indicated pressure of early fuel supply for a modern marine main engine increases as much as …... decreases:
- 33.Why the indicated engine efficiency increases when the fuel supply pressure after opening the fuel valve is higher than normal:
- 34.How the indicated engine efficiency changes when the fuel supply pressure after opening the fuel valve is lower than normal:
- 35.Which of the listed power plants requires the shortest time to safe loading from starting modes to nominal load mode?
- 36.What is the probable cause of the high temperature of the exhaust gases of marine main ICE?
- 37.What is the likely cause of the high exhaust gas temperature on one cylinder?
- 38.The effective power of the marine ICE can be indirectly determined by:
- 39.By what percentage is the overload power of the marine ICE greater than its nominal power:
- 40.By what percentage is the overload power of the marine ICE greater than its maximum power:
- 41.In what cases is a long-term excess of rotation speed of marine main ICE permissible:
- 42.Increasing which phase of the marine ICE fuel delivery most degrades the efficiency of the combustion process?
- 43.The engine efficiency indicator is at its highest value when combustion starts:
- 44.In which of the following cases does the indicated efficiency of modern marine main engines increase?
- 45.When the maximum pressure is kept constant with a decrease in the RPM:
- 46.Why is additional lubrication of the Marine diesel engines (MDE) cylinder liner required?
- 47.In which Marine diesel engines (MDE) it is necessary to supply additional oil to the cylinder liner?
- 48.In which part of the cylinder liner are the passages of the lubricaion system of a crosshead Marine diesel engines (MDE) drilled?
- 49.The zone of zero fuel discharge of the fuel injection pumps in internal combustion ship engines provides
- 50.Fuel discharge should stop when the racks of the fuel injection pumps in internal combustion ship engines
- 51.The individual increase of the effective stroke of the plunger in the fuel injection pumps of internal combustion ship engines
- 52.The uneven distribution of fuel cycle portions per cylinder, with a constant position of the lever system for controlling the fuel injection pumps, with a decrease in the RPM:
- 53.The uneven distribution of the fuel cycle portions per cylinder, with reduced position of the lever system for controlling the fuel injection pumps,with a constant RPM of internal combustion ship engines:
- 54.The maximum fuel discharge pressure, at constant RPM of internal combustion ship engines, with increased position of the lever control system:
- 55.The maximum fuel discharge pressure, at a constant position of the lever system for controlling the fuel injection pumps, with an increase in the RPM:
- 56.According to the speed curve of the fuel injection pumps, when the cyclic fuel portion decreases with a reduction in RPM, the steadiness of the operation mode of internal combustion ship engines:
- 57.When the cyclic fuel portion according to the speed curve of the fuel injection pumps increases with a reduction in RPM, the steadiness of the operation mode of internal combustion ship engines:
- 58.A sudden drop in pressure in the circulating oil system may be due to:
- 59.What is the process of cold drawing called?
- 60.A sudden increase in pressure in the circulating oil system may be due to:
- 61.The temperature of the cooling water rises with all other normal parameters. The reason is:
- 62.What should be the length of the bearing shell relative to the length of the shaft journal?
- 63.What does the clearance between the bearing shell and the crankshaft arm depend on?
- 64.With MDE, what is the number of main bearings compared to the number of cylinders ?
- 65.How is the MDE crankshaft ensured against axial displacement of the crankshaft?
- 66.Where is the Mitchel bearing usually installed ?
- 67.How do we call the clearance between the bearing and the crankshaft journal?
- 68.What happens to the clearance when the main bearing are worn?
- 69.How is the crankcase of high power crosshead engines called?
- 70.How are the "A" frame columns of the main engine fabricated?
- 71.The setting of the MDE indicator drive affects the determination of:
- 72.The indicated power of MDE:
- 73.Periodic verification of the precision of measuring instruments is called:
- 74.The reason for the significant use of copper in engineering is:
- 75.What do the properties of metals and metal alloys depend on?
- 76.Which substances are called amorphous?
- 77.The process of converting metals and alloys from liquid to solid is called:
- 78.The diagrams that determine the quantitative state of metals in alloys and their dependence on temperature and concentration of components are called:
- 79.Metals that do not oxidize when heated are called:
- 80.Materials that retain their properties and structure at high temperatures are called:
- 81.The property of metals to resist the destructive action of external forces is called:
- 82.The property of a metal to assume its original shape is called:
- 83.To which stationary part of the MDE are the crosshead guides attached?
- 84.In which part of the internal space of the "A"-shaped column of the Marine ICE does the crankshaft and connecting rod mechanism move?
- 85.What material is the "A"-shaped column of a main engine made of?
- 86.What is the purpose of the crankcase doors on both sides of the "A"-shaped column of the main engine?
- 87.Which of the listed damages leads to soot deposits and clogging of the nozzle holes of the fuel valves of marine ICE?
- 88.What valve is installed on the crankcase doors of the "A"-shaped frame of the marine main ICE?
- 89.In which part of marine main ICE are the cylinder liners installed?
- 90.By what is the main marine ICE divided into two parts ?
- 91.What pasages should the cylinder blocks of two-stroke marine main engines have?
- 92.Which marine ICEs have scavinging ports?
- 93.What material are the cylinder blocks of marine main ICE made of?
- 94.Can cylinder blocks of marine ICE be a welded structure?
- 95.What loads are marine ICE cylinder liners subjected to during operation?
- 96.How is the cylinder liner mounted in the marine ICE cylinder block?
- 97.What is formed between the sealing arrangements the cylinder block and the outer walls of the cylinder liner?
- 98.Why should marine ICE cylinder liners be able to freely expand radially and axially?
- 99.How is the cylinder liner secured to the marine ICE cylinder block?
- 100.What is the temperature load distribution of the marine ICE cylinder liner?