F4 Marine Engineering — Management Level — Page 5
704 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 401.The compression process in Marine ICE is a thermodynamic process which is affected by:
- 402.How does the indicated specific fuel consumption of the Marine ICE change as the excess air ratio increases to about 3?
- 403.How does the indicated specific fuel consumption of the Marine ICE change with an increase in the excess air ratio from approximately 3.5 upwards?
- 404.How does the indicated specific fuel consumption of Marine ICE change with a decrease in the duration of combustion?
- 405.How does the indicated specific fuel consumption of Marine ICE change when combustion starts earlier?
- 406.What must be measured to determine on board the effective specific fuel consumption?
- 407.How does the effective specific consumption of Marine ICE change as the excess air ratio increases to about 3?
- 408.How does the effective specific fuel consumption of Marine ICE change as the excess air ratio increases from approximately 3.5 upwards?
- 409.How does the effective specific fuel consumption of Marine ICE change with a decrease in the duration of combustion?
- 410.How does the effective specific fuel consumption change in modern main ICE when combustion starts earlier?
- 411.What is the condition for obtaining a speed limit characteristic of a main ICE?
- 412.What is the condition for obtaining a speed characteristic of a main ICE along the smoke limit:
- 413.What is the condition for obtaining the maximum speed characteristic of a main ICE:
- 414.What must be measured to determine on board the indicated specific fuel consumption?
- 415.In Marine ICE , the main bearings are located between:
- 416.In which of the specified systems of Marine ICE heat exchangers are most often used:
- 417.The cooling water of a main ICE is used in the fresh water generator as:
- 418.With two-stroke marine ICE, the working cycle for one cylinder is carried out every:
- 419.The scavinging ports of a low-speed two-stroke ICE are opened and closed by:
- 420.If a 4-stroke diesel engine is started with direct air in the cylinders, the piston in the cylinder must be in which position:
- 421.What is the hydrodynamic efficiency of a free propeller?
- 422.What is the hydrodynamic efficiency of a propeller mounted on a ship:
- 423.When is the hydrodynamic efficiency of the propeller maximum?
- 424.The propeller curve is a curve of:
- 425.The main ICE works at points of the same propeller curve when:
- 426.The process of removing moisture from the air is known as:
- 427.The advantages of the impulse system for pressure charging of the marine ICE are:
- 428.The difference between a pulse system and a constant pressure system in turbochargers is in:
- 429.What can cause turbocharger surging?
- 430.What effect will the late fuel injection and high exhaust temperature have on a turbocharger:
- 431.What could be the reason for the appearance of vibrations in turbocharger:
- 432.At full load of the main engine, the RPM of the turbocharger is too low. What could be the reason?
- 433.A two-stroke engine usually has an auxiliary blower, which is used:
- 434.A high exhaust gas temperature on all cylinders in a 4-stroke trunk piston engine can occur due to:
- 435.The speed of rotation of the turbocharger depends on:
- 436.One of the functions of the air receiver of marine internal combustion engine is:
- 437.Which of the following turbocharging systems has the lowest turbine side efficiency?
- 438.Is it possible to have the same size turbocharger fitted to different power engines?
- 439.Can we represent the mean indicated pressure as the work done per unit of volume?
- 440.Which parameter of the marine internal combustion engine is essential in the operation of the propulsion system according to external characteristics?
- 441.When is boiling possible in the downcomers of a natural circulation water tube boiler?
- 442.When is cavitation possible in the downcomers of a water tube boiler?
- 443.The property of a metal to resist the penetration of solid bodies into it is:
- 444.The diagram of the two-component iron-carbon system, which serves to determine the characteristic structures of iron alloys, is called:
- 445.The bound carbon in cast irons is found in the form of:
- 446.Main marine diesel engine, controlled by a properly working governor with a load limiter, when it cannot reach the set RPM, works on:
- 447.The fuel injection in the marine diesel engines is fully released after:
- 448.The thrust created by the propeller is greatest when the ship:
- 449.The speed of the propeller slip is defined as the difference between:
- 450.The thrust created by the propeller is greatest when the propeller slip is:
- 451.The propeller slip is maximum when the propeller is rotating and the ship:
- 452.The power of mechanical losses of marine internal combustion engine remains almost constant when we change:
- 453.Main marine diesel engine, equipped with a speed governor, with a constant setting of the governor and a change in the external resistance, works on:
- 454.How can we determine what type of freon is poured in a freon bottle without a label?
- 455.How can it be determined that a refrigeration compressor is running wet?
- 456.in ordert to exclude the influence of the hydraulic resistance of the evaporator, it is necessary after throttling in the thermo-regulating valve to have:
- 457.What process takes place with the refrigerant in the distributor placed between the thermo-regulating valve and the evaporator?
- 458.By tightening or untightening the thermo-regulating valve spring, the following is adjusted:
- 459.In the case of horizontal installation of a steam-filled balloon, where should the thermo-regulating valve be located?
- 460.How can be checked that the temperature sensing system of a dismounted thermo-regulating valve is operational?
- 461.If the evaporator is correctly filled with freon, the reason for a higher than desired temperature in the cooled room can be:
- 462.Which definition of entropy is most implausible (unlikely)?
- 463.In the ports of the European Union, the sulfur content of the fuels without consecuent treatment used on the ship cannot exceed:
- 464.How is the term "latent heat" defined?
- 465.How do we define the term "modulus of elasticity" for machine elements?
- 466.What is the temperature of the working medium at the beginning of the compression process compared to the temperature of the cylinder walls?
- 467.In the process of compression during its movement to TDC, the temperature of the working medium in a marine diesel engine:
- 468.What is the name of the thermodynamic process in which the parameters of the working medium change at a constant volume?
- 469.Which parameter remains constant in the adiabatic process?
- 470.To simplify the thermodynamic calculation of the actual cycles in marine diesel engines, we assume that the polytropy index is:
- 471.If, with constant fuel supply, we reduce the engine speed, what changes in the engine parameters will we notice?
- 472.Which mechanism controls the opening of the marine diesel engine starting valves?
- 473.The purpose of turning the crankshaft of a diesel engine manually or with a shaft turning gear is:
- 474.The purpose of the marine diesel engine air distributor is:
- 475.What is the number of starting valves in a marine diesel engine?
- 476.Is the main starting valve a mandatory component in the marine diesel engine starting system?
- 477.The connection of the starting system with the compressed air bottles is carried out by:
- 478.Reversal of marine diesel engine is required in case of:
- 479.What should we change when reversing a marine diesel engine?
- 480.Are four-stroke marine diesel engines reversible?
- 481.What is the purpose of the interlocks (blocking devices) in the reversing system of a marine diesel engine?
- 482.Which element of the air starting system is used for the repeated start of the engine in case of open compressed air cylinders?
- 483.At what minimum temperature in the engine room the main engine can be started?
- 484.How is forced circulation carried out in marine steam boilers?
- 485.Marine steam boilers that have their own combustion chamber are called:
- 486.The indicator that characterizes the load of the boiler during operation is called:
- 487.What are the main parameters of the steam produced by the marine steam boilers?
- 488.When a marine ICE is controlled by an all-speed governor, with steady operating mode, its operating point is the intersection of:
- 489.When a marine diesel engine is manually controlled by the local station, with steady mode of operation, its operating point is the intersection between:
- 490.When a marine diesel engine is controlled by an all-speed speed governor, at bad wheather condition, the operating points are located on:
- 491.When a marine diesel engine is manually operated by the local station, in case of bad wheather, the operating points are located on:
- 492.With a light propeller curve, the operating point of the marine diesel engine can be located in the short-time overload area when:
- 493.Witha light propeller curve can the marine diesel engine be loaded to the rated power:
- 494.Carbon is a graphite-forming element. Most often, its amount in cast iron is:
- 495.The substance that increases the brittleness of cast iron, its tendency to form gas bubbles and cracks is called:
- 496.Which properties of cast iron depend on the size of graphite additives?
- 497.What is done to the leading edge of steam turbine blades to increase their corrosion and erosion resistance and reduce inlet losses.
- 498.Bandaging the blades in their upper part serves:
- 499.The sealings used in steam turbines are:
- 500.The bearings that absorb all the radial forces of the rotor and serve to center the rotor to the turbine body are called: