F6 Maintenance and Repair — Management Level — Page 3
507 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 201.How is the refrigeration compressor protected from water hammer?
- 202.What is the purpose of a differential pressure switch in air conditioning systems?
- 203.Which of the following hydraulic machines work only as pumps and cannot work as hydraulic motors?
- 204.Settling tanks on ships are an element of:
- 205.The ways to clean fuels on board are:
- 206.The permissible water content of marine fuel shall not exceed:
- 207.settling is a method which.................. in fuel cleaning:
- 208.Coarse cleaning filters are filters for:
- 209.The retention of mechanical impurities and water is a principle of fuel cleaning through:
- 210.Which of the listed damages leads to soot deposition and clogging of the nozzle holes of the fuel valves of marine diesel engines?
- 211.During the operation of the ME on CSR, on one of the cylinder groups the temperature of the exhaust gases rises sharply and the turbocharger begins to surge. What could be the reason?
- 212.The earlier start (1 to 3 degrees advance) of fuel injection in the main marine engines causes:
- 213.In what cases a ship's main engine can operate with an earlier start (1 to 3 degrees advance) of fuel injection:
- 214.During a routine check we notice a slight circular light between the carbon brushes and the rotor contact rings at 70% generator load. What will we do?
- 215.When the maintenance of an air compressor is complete and we are ready for test run it, it is important to:
- 216.Some engines use copper gaskets between the fuel valves and cylinder heads . Why is it important that these gaskets are original?
- 217.When testing fuel valves for opening pressure, the bench pump must be handled carefully. How?
- 218.Due to inspection or repair, the boiler has to be emptied. If we have enough time, how will we conduct this operation?
- 219.What is the most likely cause of the main bearings overheating?
- 220.Which of the following operations is not recommended in the event of a fire in the water economizer?
- 221.The radial oil clearance in the bearings of the turbocharger units is measured at turbocharger:
- 222.In which of the indicated failures does the indicated efficiency increase in modern engines?
- 223.Axial damping packages in turbocharger units serve to:
- 224.Radial damping packages in turbocharged units serve to:
- 225.The axial clearance between the compressor wheel and the air-outlet housing is about:
- 226.Radial clearances for labyrinth grooves are around:
- 227.The gear oil pumps that lubricate the turbocharger units of the VTR series are attached to:
- 228.After installing the oil pump of the turbocharger unit, should the radial and bore be checked?
- 229.With a constant position of the unit controling the cycle portion of the high pressure fuel pump - the changing over from light to heavy fuel during operation of the marine diesel engines occurs:
- 230.The influence of which of the phases of fuel injection can be compensated by setting the high pressure fuel pump?
- 231.The follow-up mechanism for electrohydraulic steering gears:
- 232.Will the rotational frequency of a running wound-rotor induction motor change if the resistance in its rotor circuit is increased?
- 233.How should the passage of electric cables through watertight partitions be structurally implemented?
- 234.Damage to contacts inside cargo winch control stations caused by condensation can be reduced (preventatively avoided) by:
- 235.Which of the following valves closes first during a prolonged shutdown of the refrigeration plant?
- 236.Which of the following valves is closed during refrigeration compressor start-up?
- 237.The probability of water entering the system of a refrigeration plant during charging with liquid freon is greatest when:
- 238.What is the first step in reducing carbon deposits on air compressor discharge valves?
- 239.What is the main purpose of gas analysis in marine steam boiler?
- 240.When is cavitation possible in the downpipes of water pipe marine steam boilers?
- 241.Which statement is false about regenerative air heaters?
- 242.The temperature in the area of the screen tubes in water-tube boilers is up to (1500-1700)°C, and the metal melts at (1200-1300)°C. Why does the metal not plasticize in this?
- 243.Which type of corrosion is most common in marine steam generators?
- 244.What is the main type of corrosion on waste heat boilers?
- 245.What is the main cause of circulation failure in marine steam boilers?
- 246.In what cases is it permissible for a ship's main engine to operate with a later start of injection (delay)?
- 247.The later start (delay) of injection in the main marine engines causes:
- 248.When operating on light fuel versus operating on heavy fuel, the mechanical stress is:
- 249.When operating on heavy fuel with a higher preheat temperature, the mechanical stress is:
- 250.When operating on heavy fuel with a higher preheat temperature, the thermal stress is:
- 251.When operating on light fuel with a higher cetane number compared to operating on heavy fuel, the heat stress is:
- 252.Which of the following indicators change significantly during the changing over from light fuel to heavy fuel and vice versa:
- 253.The changing over from light to heavy fuel and vice versa is done as slowly as possible in order to:
- 254.If the color of the surface layer of the main bearing cap is black and has increased hardness, and there are scratches on the main journal of the crank shaft, what is the possible cause?
- 255.Where in centrifugal pumps is the surging possible and where is the cavitation possible?
- 256.Which of the following causes does not increase the temperature of an air reciprocating compressor?
- 257.Ship fuel oil separators are mainly:
- 258.By water interface of the separator we mean:
- 259.Does the use of untreated fuel affect the operation of the marine diesel engines?
- 260.Can fuel separation replace fuel filtration?
- 261.Which of the following malfunctions can cause the engine to smoke?
- 262.If the coolant temperature at the outlet of an auxiliary engine is lower than normal, the most likely cause is:
- 263.What will be the effect on the lube oil cooled piston if you stop the oil pump immediately after stopping the engine?
- 264.During the unmanned operation of the main engine, the revs of turbo compressor increased during the night. The reason for this could be:
- 265.The turbo compressor (at constant pressure) makes a "coughing" noise. What could be the reason?
- 266.After how many running hours should the bearings/rolling/of the turbo compressor be replaced, even if they appear to be in good condition?
- 267.To prevent moisture condensing from the air in the diesel generator air cooler it is recommended:
- 268.An increase in which stage of fuel injection of the marine diesel engine decreases the efficiency of the combustion process the most:
- 269.The pressure in the condenser of a refrigeration system is mainly determined by:
- 270.When the temperature in the refrigerating chambers reaches the set value, the compressor works with:
- 271.When we bleed the system, the compressor is:
- 272.The presence of air in the refrigeration system:
- 273.Where do we release the air or other gases from the refrigeration system?
- 274.With the compressor stopped, how can we determine the amount of freon in the system if there is no sight glass on the condenser?
- 275.With the compressor running, how can we determine the amount of freon in the system if there is no sight glass on the condenser?
- 276.With a small shortage of refrigerant, the cooling performance of the evaporator:
- 277.With a small shortage of refrigerant, the temperature in the refrigerating chamber:
- 278.With a small shortage of refrigerant, the cooling performance of the compressor:
- 279.Refrigerator compressor, which is controlled by a pressure switch, in case of a small shortage of refrigerant:
- 280.Why is it necessary that the height of the water column above the inlet edge of the pipe in the steam manifold does not fall below the level established by the manufacturer?
- 281.What is the main problem of hydraulic tests of steam boilers carried out without dismantling the mountings?
- 282.Which nozzles are started first when the fire tube boilers are heated?
- 283.During the operation of the steam boilers, we find that the water level is not noticeable, when blowing, it appears, but immediately rises. What is the reason?
- 284.What is the visual indication of overheating of fuel oil?
- 285.After boiler cleaning, what are the most correct actions when heating up a cold boiler?
- 286.In waste heat boilers, low-temperature corrosion of the heating surfaces occurs at low engine loads. This is due to the presence of:
- 287.Before starting the boiler burner, which of the following actions is most important?
- 288.What is the main purpose of boiler bottom blowdown?
- 289.The safety valve of the auxiliary steam boiler must:
- 290.What action will you take if the pH of the boiler water is below 7?
- 291.What action will you take if the pH of the boiler water is more than 11?
- 292.What are the most likely consequences of oil contamination of boiler water?
- 293.Performing a hydraulic test through the feed pumps of the steam boiler shall be:
- 294.The preparation of the turbo gear unit for operation must ensure:
- 295.Which preventive action should we take as a priority before starting the turbine warm-up?
- 296.Which of the methods for warming up the turbine is carried out as a priority in marine steam turbines?
- 297.For which turbo gear units should passing through the critical revolutions be as fast as possible?
- 298.Which parameter is critical in finalizing turbine warming up?
- 299.Which parameter is critical when warming up the turbines?
- 300.How often are the rotors of the turbines turned /with working oil systems/ in case of prolonged inactivity of the turbines?