F6 Maintenance and Repair — Management Level — Page 2
507 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 101.With worn o-rings on a water-cooled air compressor cylinder liner, where is water most likely to appear when starting the compressor?
- 102.Sometimes a deposit forms on the high pressure discharge valves of the air compressor in a very short time, even with frequent replacement of the high pressure valves. What could be the reason?
- 103.What should be done if the lubricating oil acquires a yellowish-white color (emulsion)?
- 104.What action should be taken if the air compressor crankcase relief valve trips?
- 105.What actions will you take if you have an engine gas leak due to worn piston rings and the circumstances do not allow you to stop the engine and perform an engine overhauling:
- 106.In the event of a fire in the under piston compartment of the engine, which of the following components will suffer the most serious damage?
- 107.Why is it necessary to turn the engine before starting (slow turning with air)?
- 108.Which of the listed regulating indicators is measured when checking and adjusting the static phases of supply of the valve type high pressure fuel pump of the marine dieasel engine?
- 109.At the expense of which indicator are the newer generations of marine diesel engines less sensitive to the wear of their cylinder-piston groups?
- 110.How will the mechanical efficiency change as cylinder-piston group wear increases?
- 111.Which performance parameter is decisive in evaluating the thermal load of the cylinder liner?
- 112.What diagnostic information does the indicator diagram, expanded by the angle of rotation of the engine crankshaft, carry?
- 113.By what percentage does the specific effective fuel consumption increase for one degree delay in the start of fuel injection by the nozzles?
- 114.Distinction between leakage of the exhaust valve and wear of two or more piston rings can bе made by:
- 115.When two or more piston rings are worn, the increase in cylinder lubrication:
- 116.The rate of the pressure rising in the fuel line, before the fuel valve opens diagnoses:
- 117.What effect does the reduction in the rate of rising of pressure in the fuel line before the opening of the fuel valve have on the other indicators of fuel injection:
- 118.How does the indicated engine efficiency change when the rate of rise of pressure in the fuel line before opening the fuel valve decreases:
- 119.Lowering of the maximum fuel pressure Pj. max of the marine diesel engine during operation in maneuvering modes is due to:
- 120.The main reason for increasing the roughness of propellers during operation is
- 121.Which of the listed reasons causes a decrease in the elasticity of the piston rings of the marine diesel engine?
- 122.The check and implementation of static adjustment of the high pressure fuel pump of the marine diesel engine is carried out according to data from:
- 123.By periodically controlling the deflection of the marine diesel engine crankshafts, you can establish:
- 124.Low-temperature corrosion is caused by the presence in the boiler fuel of:
- 125.What operation is planish?
- 126.What does the mechanical efficiency depend on and how?
- 127.In what range does the effective efficiency of modern marine main engines run?
- 128.What oil temperature do we call "critical"?
- 129.Which of the listed reasons for increasing the temperature in the area of the first piston ring do we consider to be the most intense and the most dangerous?
- 130.In which of the following cases the drier can absorb the most moisture from the refrigerant?
- 131.What does the sign A1 mean added to the ship's class symbol?
- 132.Which operation must be started immediately before the loading operation and terminated immediately after its completion?
- 133.What daily rate of fresh water should we guaranteed in the voyage planning calculations?
- 134.What type of cargo system are VLCC/ULCC equipped with?
- 135.The ship PMS aims to:
- 136.What is the cause of cavitation damage to МЕ cylinder liners?
- 137.Which of the following indicators characterizes the wear of the fuel valve?
- 138.DG (ME) startup is permanently unblocked in the following cases:
- 139.In which of the following cases is the fuel injection unblocked?
- 140.Why is a DC motor connected to the main busbars through starting resistors?
- 141.Why should the starting resistors be switched off in a running mode of a DC motor?
- 142.What is the reason for a shorted rotor induction motor humming but not spinning (connected to the mains busbars) with a mechanically sound motor and working mains?
- 143.How can the direction of rotation of a three-phase induction motor be changed?
- 144.What insulation resistance of a working electric machine is considered normal?
- 145.Which fuel advance angle θ do we define as nominal?
- 146.For which engines is the Jet Shaker Cooling System developed and implemented to cool the pistons with oil?
- 147.For which engines and for what purpose is the VEC system developed?
- 148.The API class of oils reflects in letters of the English alphabet:
- 149.230/380 V is indicated on the nameplate of a three-phase Asynchronous motor. How will we connect the phases of its stator winding to connect it to a standard voltage of 380 V?
- 150.In which of the following accidents can a DC generator produce higher but also lower than normal voltage?
- 151.Why do we have to empty the overflow tank before bunkering?
- 152.During a routine check in UMS mode, the duty engineer notices an elevated level in the FO overflow tank. What should his actions be?
- 153.Before engaging the turning gear, you must:
- 154.Which of the consequences causes the clogging of the nozzle openings of the fuel-valves during the operation of the marine diesel engine?
- 155.What actions are necessary when the pH of the boiler water > 11?
- 156.Entry of oil into the water cooling system of the Ship ME will cause:
- 157.What is the normal operating limit of the isodrome needle on the UG-8 type governor?
- 158.How does the opening of the needle on the isodrome affect the performance of the revolutions automatic control system?
- 159.How does the free play in the linkage between the governor and the fuel racks affect the engine operation?
- 160.If the athomizer has 10 holes, at how many clogged holes it has to be replaced?
- 161.What will be the effect of nozzle leakage after the injection is finished?
- 162.The transition from heavy to light fuel must be carried out:
- 163.How do we recognize a leaking fuel valve during testing?
- 164.Which of the listed indicators is used when checking and adjusting the position of the cams of the high pressure fuel pump-valve type of marine diesel engine?
- 165.Which of the indicated indicators characterizes the degree of wear/deterioration of the hydrotightness/ of the high pressure fuel pump?
- 166.How many times will the heat load on the stator windings increase if the current load of an induction generator is doubled?
- 167.Maximum fuel pressure is a diagnostic indicator for:
- 168.When is it dangerous for the fuel injection pressure after opening the fuel valve to be higher than normal?
- 169.Why does the indicated engine efficiency decrease when the fuel injection pressure after opening the fuel valve is lower than normal:
- 170.What device can be used to measure the insulation resistance of the elements of the ship's electrical equipment?
- 171.In what range should the current be when charging a 12V 160Ah acid battery normally?
- 172.What should be the electrolyte density of an lead-acid battery in a fully charged state?
- 173.How many amperes is the power diode current in a three-phase rectifier if the load current is 60A?
- 174.In what range is the usual thyristor control voltage?
- 175.Observing the order of service of the separators is important. Why?
- 176.When should an oxygen analyzer be calibrated?
- 177.Which of the indicated parameters characterizes the wear of the fuel valves of the marine diesel engines?
- 178.The fuel nozzles are opened automatically by the fuel pressure set by high pressure fuel pump. The adjustment of the opening pressure is done by:
- 179.From a thermodynamic point of view, engine cooling:
- 180.What does the increased pressure in the crankcase of trunck-piston engines indicate?
- 181.When the pressure of a centrifugal seawater cooling pump rises, this is a signal for:
- 182.What propeller should we prefer for a vessel intended for towing?
- 183.What will happen if we run a centrifugal pump with the discharge valve closed?
- 184.Due to misalignment of the high pressure fuel pump drive, the advance angle of fuel injection has changed to increase, above the optimum. What will happen?
- 185.If a hydraulic pump of a hydraulic windlass overheats, the reason may be:
- 186.As a rule, the oil reservoir/tank/ in a hydraulic system at a normal level should have a volume of:
- 187.When sailing in ballast, the propeller curve are light and vibrations are noticeable in the ship's hull. By what parameter do we limit the load of the main marine diesel engine?
- 188.Oil deteriorates faster in refrigeration compressors with performance regulation through:
- 189.Why is it prohibited to add methylated spirits to the refrigeration system to remove moisture?
- 190.For gear pumps, the permissible radial clearance is in a wide range - from 0.003 to 0.2mm or δρ\>0.0015D of the gear wheel. What is the effect of increased clearance?
- 191.Which parts of the centrifugal pump are most subject to wear and are usually replaced at each scheduled maintenance?
- 192.What action will we take if the heat exchanger reduces the cooling rate, but the amount of heat to it and the flow rates of the fluids remain unchanged?
- 193.How will we protect the boiler from corrosion if it is not used for a long time?
- 194.How are we going to mount a press assembly rolling bearing to a centrifugal pump shaft?
- 195.A resistance of unknown value can be checked/measured using the voltmeter-ammeter method. How should the two devices be connected to the resistance?
- 196.What type of charger should be used to charge lead acid batteries to maintain a "full charge" provided they are not used for an extended period?
- 197.Steering gear overload protection:
- 198.When is it disadvantageous for the fuel injection pressure after opening the fuel valve to be lower than normal:
- 199.Low fuel valve opening pressure can be caused by:
- 200.What is common in the design of systems served by positive displacement pumps?